Add support for the gmac ethernet interface to pinctrl. This hardcodes
the setup to match that of the firefly and Radxa Rock2 boards, using the
RGMII phy mode for gmac interface and GPIO4B0 as the phy reset GPIO.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
SDMMC-PWREN is a pin to control voltage for SDMMC IO, it may
be high active or low active, the dwmmc driver always assume
the sdmmc-pwren as high active.
Kernel treat this pin as fixed regulator instead of a pin from
controller, and then it can set in dts file upon board schematic,
that's a good solution, we can also do this in u-boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK818 PMIC contains a charger. Add very basic charger functionality
to be able to regulate the USB input current and charger shutdown limits.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enabling CONFIG_SPL_POWER_SUPPORT will cause a compiler warning:
‘get_ldo_reg’ defined but not used [-Wunused-function]
Let's wrap get_ldo_reg(), rk808_ldo and rk818_ldo with ENABLE_DRIVER
which is only set for non SPL builds.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use dev_read_bool() instead of fdt_getprop() to get the property
from DTS. And add a comment for "hnp-srp-disable" property to
fully describe its effect.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change migrates the USB_DWC2 configuration item to Kconfig
and runs moveconfig to adjust header files and defconfig.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Split off into a separate patch:
Ran moveconfig to migrate other boards:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use fixed regulator to control the voltage of vbus. Enable vbus
supply when usb start and disable vbus supply when usb stop.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The xhci-rockchip driver depends on DM_REGULATOR and DM_USB.
So add dependent features for xhci-rockchip driver in Kconfig.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some address relevant varibable is defined originally as u64. To
compatible with arm32, this patch change them to uintptr_t type.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The origin patch get rockchip dwmmc by name 'ciu', which lead
to the SPL not able to remove 'clock-names' node in dts.
I'm not saying this is not correct, but I would prefer to handle
this in dts or clock driver to save memory for SPL.
For example the rk3288 SPL size has out of memory if not enable
BACK_TO_BROM option, there are many other SoCs has less internal
memory than rk3288.
This reverts commit 480a9b834c.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency for
all rockchip SoC dwmmc controller.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip rk322x sysreset is much like rk3036 and other Rockchip SoCs,
only difference is that the target register address is different.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the serial driver (ns16550 and compatible) used for the
Rockchip devices.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the Gigabit Ethernet MAC (i.e. common designware driver and
rockchip-specific wrapper).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the dw_mmc and sdhci wrapper drivers for Rockchip.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This change covers the USB3 (xhci) driver for the Rockchip devices.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This change covers the rk_spi.c (SPI driver) used in Rockchip devices.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This change covers the pinctrl drivers for the Rockchip devices.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ARCH_OMAP2 has been renamed ARCH_OMAP2PLUS in commit a93fbf4a78
("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
To set wait state, a hard coded value is used instead of using
latency parameter. stm32_flash_latency_cfg() is currently used
in arch/arm/mach-stm32/stm32f4/clock.c and in
drivers/clk/clk_stm32f7.c with, in both case, "5" as parameter.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This driver is used in another board; remove board information from
the driver debug log.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
set_state_ops is kept under PINCTRL_FULL flag in order
to decrease memory footprint in some configuration.
PINCTRL_FULL can be enabled for debug purpose.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
There is no need to duplicate same option with different name.
Kill HW_WATCHDOG_TIMEOUT_MS in favor of WATCHDOG_TIMEOUT_MSECS.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add missing static to serial_stub_puts().
Unexport serial_stub_{getc,tstc} because they are used locally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
fix warnings:
drivers/usb/gadget/at91_udc.c:1344:12: warning: 'at91rm9200_udc_init' defined but not used [-Wunused-function]
drivers/usb/gadget/at91_udc.c:1379:13: warning: 'at91rm9200_udc_pullup' defined but not used [-Wunused-function]
drivers/usb/gadget/at91_udc.c:1476:12: warning: 'at91sam9263_udc_init' defined but not used [-Wunused-function]
Signed-off-by: Heiko Schocher <hs@denx.de>
After the commit SHA1: 842778a091 - the serial number descriptor is only
visible when we have non zero length of g_dnl_serial.
However, on some platforms (e.g. Siemens) the serial number is set at
g_dnl_bind_fixup(), so with the current code we will always omit the
serial (since it is not set).
This commit moves the g_dnl_bind_fixup() call before the g_dnl_serial
length test.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These are only used in drivers/mis/i2c_eeprom.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix warnings reported by sparse:
- ... was not declared. Should it be static?"
- cast to restricted __be32
While fixing those, the type conflict of cci500_init() was found.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
According to rk3036 TRM, pll_con1[12] should be set to '1' for the pll
integer mode, while the '0' means the frac mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
fix menutext for the options SPL_DM_SERIAL and TPL_DM_SERIAL.
Both have the same text as DM_SERIAL, which is
confusing.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
commit dfe64e2c89
Author: Sergey Lapin <slapin@ossfans.org>
Date: Mon Jan 14 03:46:50 2013 +0000
mtd: resync with Linux-3.7.1
modified onenand_block_markbad to call mtd_block_markbad,
but as _block_markbad function pointer used by mtd_block_markbad
to do actual job is by default pointing back to
onenand_block_markbad there is no way this function ever
finishes its job.
Fix it by changing function body according current (4.12-rc6)
linux implementation.
Tested on IGEPv2 board with Muxed OneNAND(DDP) 512MB containing
several unerasable blocks this function marked bad.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Current implementation is unable to access second half of
DDP OneNAND flash (reads first half mirrored). Use block
and bufferram address calculations from onenand_base to
fix this.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
The variables gpll_init_cfg and apll_init_cfg are unused in this file,
remove them.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In armada_37xx_gpiochip_register, the return value of fdtdec_get_bool
should be true when gpio-controller is found; current codes makes a
wrong inverse return value judgement, this patch fixes it.
Signed-off-by: Ken Ma <make@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
If north bridge selection register bit1 is clear, pins [10:8] are for
SDIO0 Resetn, Wakeup, and PDN while if bit1 is set, pins [10:8]are for
GPIO; when bit1 is clear, pin 9 and pin 10 can be used for uart2 RTSn
and CTSn, so bit1 should be added to uart2 group and it must be set
for both "gpio" and "uart" functions of uart2 group.
Signed-off-by: Ken Ma <make@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The driver currently does not reset bit 5 of the hostctl register even if
the MMC stack requests it. Then means that once a bus width of 8 is
selected it is not possible to change it back to 1. This breaks
'mmc rescan' which needs to start off with a bus width of 1.
The problem was surfaced by enabling CONFIG_DM_MMC_OPS on tegra. Without
this option the MMC stack fully reinits the driver on a 'mmc rescan'.
But with this option driver model does not re-probe a driver once it has
been probed once.
Fix the driver to honour the request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Chubb <peter.chubb@data61.csiro.au>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move the only use of CONFIG_SF_DUAL_FLASH to defconfig. This makes the
associated topic_miamiplus.h header obsolete, so remove that as well.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reuse invoke_smc() routine which is already defined
instead of duplicating same at multiple places.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop include of netdev.h as it's a SATA driver not a network driver.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
With gcc-6 and later we see warnings that at91sam9263_udc_caps and
at91rm9200_udc_caps are unused.
Fixes: 620197670a ("usb: gadget: at91_udc: add at91_udc into U-Boot")
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
Current implementation doesn't allow utilization of platform-specific
reads and writes.
But some arches or platforms may want to use their accessors that do
some extra work like adding barriers for data serialization etc.
Interesting enough OHCI accessors already do that so just aligning
EHCI to it now.
This is a resend of http://patchwork.ozlabs.org/patch/726714/
Back in the day this patch broke some PPC and Sandbox boards
as they we missing inclusion of "asm/io.h". Those missing items were
fixed with:
1) http://patchwork.ozlabs.org/patch/751397/
2) http://patchwork.ozlabs.org/patch/771099/
So now it should be safe to apply this patch.
FWIW TravisCI builds everything with all 3 patches in place,
see https://travis-ci.org/abrodkin/u-boot/builds/239563813
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
In current code, after running the command of "usb start", the controller
will keep in otg mode and can't switch to host mode if not support
SNP/SRP capability. So add the property of "hnp-srp-disable" in the DTS
to config the contrller work in force mode of host.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Commit a058052c changed the generic phy_reset() to clear all bits in
BMCR. This inevitably clears the ANEG bit. m88e1145 requires any
change to ANEG bit to be followed by a software reset. This seems to
be different from other PHYs. Implement read-modify-write procedure
for this PHY init.
Signed-off-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simplify baud rate register formula and use the oversampling
uart feature.
This code is aligned with what is implemented in kernel driver
drivers/tty/serial/stm32-usart.c since kernel v4.9.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
stm32x7.c driver is dedicated for STM32F7.
In kernel, "st,stm32-usart" and "st,stm32-uart" compatible
strings are dedicated for STM32F4.
To keep U-boot and kernel aligned, replace the serial compatible
string from "st,stm32-usart", "st,stm32-uart" to
"st,stm32f7-usart", "st,stm32f7-uart" specific for STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
Detect with a previous boot loader has already set up the clocks and set
them up again so that U-Boot gets what it expects.
Signed-off-by: Simon Glass <sjg@chromium.org>
Shifted masks are the standard approach with rockchip since it allows
use of the mask without shifting it each time. Update the definitions and
the driver to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
On reset the standby bit is clear, but if U-Boot is chain-loaded from
another boot loader it may be set. Clear it before starting up video so
that it works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby':
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add remove() methods for EDP and VOP so that U-Boot can shut down the
video on exit. This avoids leaving DMA running while booting Linux which
can cause problems if Linux uses the frame buffer for something else.
It also makes it clear what is needed to shut down video.
While we are here, make rkvop_enable() static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby':
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If U-Boot is the secondary boot loader, or has been run from itself, the
SOR may already be powered up. Powering it up again causes a hang, so
detect this situation and skip it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
For devices that need a delay between SPI transactions we seem to need an
additional delay before the first one if the CPU is running at full speed.
Add this, under control of the existing setting. At present it will only
be enabled with the Chrome OS EC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file does not report a few possible errors and one message is missing
a newline. Fix these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There is some inconsistency between uses of CONFIG_RTC_DS13xx and
CONFIG_SYS_RTC_DS13xx. Address this by dropping the "SYS" from
these variables.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With overrun enabled, serial port console freezes & stops receiving data with
overun error if we keep sending data.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
Documents the externally visible functions shared between the VOP
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documents the externally visible functions shared between the HDMI
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the warning,
---8<---
CACHE: Misaligned operation at range [3fdffff0, 3fdffffc]
---<8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.
Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to avoid future confusion with similary named files, rename
tve.c to tve_common.c. New name better represents the fact that this file
holds code which can be and will be shared between multiple drivers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage
enable/disable functions for lp87565 family of PMICs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
