This is required for proper operation of the 8-bit data transfers.
This fixes transient errors seen on BeagleBone Black.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The MAC address is located at at the last 64K of SPI Flash, and
it's 6 bytes long. This patch corrects both the length and
starting byte of the MAC address.
Signed-off-by: Adam Ford <aford173@gmail.com>
commit 21af33ed03 ("ARM: davinci: omapl138_lcdk: Enable DM_MMC")
wanted to enable DM_MMC only for U-Boot and not for SPL.
But CONFIG_DM_MMC is defined for SPL build too. Because of this
MMC device was not getting registered for SPL causing MMC/SD
boot breakage.
Instead use CONFIG_IS_ENABLED(DM_MMC) which will remain false until
CONFIG_SPL_DM_MMC is defined.
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Peter Howard <phoward@gme.net.au> #omapl138_lcdk
This patch adds Microchip MPFS Icicle board support.
For now, NS16550 serial driver is only enabled.
The Microchip MPFS Icicle defconfig by default builds
U-Boot for M-Mode with SMP support.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since we have added the PCI support to the 'virt' target, enable
e1000 and NVME as alternate network and storage devices for these
virtio based devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Enable the new GEMGXL MGMT driver so that GEM 10/100 Mbps works now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Puma SoMs have a 4 MB SPI NOR flash.
Therefore we can move the environment to the end of the flash
(4 MiB - 16 kiB) in order to not overlap with SPL.
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add a short note about how to boot U-Boot on Nyan-big using tegrarcm.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
LS1028A is an ARMv8 implementation. LS1028ARDB is an evaluation
platform that supports the LS1028A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pull DRAM layout configuration code into rcar-common.c instead of
having it in multiple copies across board files. This poses no
change for Salvator-X/XS, ULCB and Ebisu boards, however it adds
a bit of extra code for Draak and Eagle boards, which now gain
the capability of being passed in the DRAM layout by the ATF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The gdsys gazerbeam board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 2x 10/100 Mbit/s Ethernet (optional)
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Replace the boolean parameter of io_check_status that controls whether
the status is printed or not with a documenting enum.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
More recent versions of IHS FPGAs feature a different memory layout.
Add a Kconfig option to differentiate between the legacy layout, and the
new layout (which is used on the upcoming "Gazerbeam" and later boards).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Future gdsys boards will switch from the legacy drivers in board/gdsys/common
to DM-based drivers.
Define a Kconfig option that disables the legacy drivers.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The "manual" RAM configuration should not be used if the DM RAM driver
is active, hence, disable the code if the CONFIG_MPC83XX_SDRAM config
variable is defined.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Move CONFIG_SYS_FPGA0_BASE, CONFIG_SYS_FPGA0_SIZE, CONFIG_SYS_FPGA1_BASE, and
CONFIG_SYS_FPGA1_SIZE to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since the gpio output status on MPC8xxx cannot be read back, it has to
be buffered locally.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The ppc4xx architecture was removed, and with it several old gdsys 44x
boards, but some "debris" from these purged boards was left over.
This patch removes these remnants (mostly entries in Makefiles, some now
superfluous data structures and some now obsolete config variables from
the whitelist).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The initialization sequence in the newest release notes of the 88e1518
phy omits two commands.
Remove them from the sequence.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
For the DM case, use the proper parameter for the regmap_init_mem call
(which is the ofnode, not the udevice).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
