Pick R-Car Gen3 R8A77961 M3W+ power domain header from Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Update commit message
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
Synchronize R-Car device tree headers with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
This is only a copyright and SPDX identifier update, no
functional change.
The following script has been used for the synchronization:
$ for i in $(cd include/dt-bindings/clock/ ; ls -1 r8a*) ; do cp /linux-2.6/include/dt-bindings/clock/$i include/dt-bindings/clock/ ; done
$ for i in $(cd include/dt-bindings/power/ ; ls -1 r8a*) ; do cp /linux-2.6/include/dt-bindings/power/$i include/dt-bindings/power/ ; done
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The HiFive Unmatched board has a M2 slot for NVME and a PCIe slot that
can also be used for NVME. Enable support for a second NVME device, so
that software RAID-1 configurations can be supported at the u-boot
level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Original OpenSBI (without FW_PIC) will relocate itself
from 0x1000000 to 0x0. After OpenSBI added FW_PIC codes,
it will not relocate any more and always run at 0x1000000.
Hence, it may overlap with Kernel memory region. So it is
necessary to change OpenSBI address from 0x1000000 to 0x0.
More details can refer to commit cb052d7712
("riscv: qemu: spl: Fix booting Linux kernel with OpenSBI 1.0+")
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Add src and dst address checking, if they
are the same address, just return and don't
copy data anymore.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When fit image boots from ram, the payload will
be prepared in the address of SPL_LOAD_FIT_ADDRESS.
In spl fit generic flow, it will malloc another
memory address and copy whole fit image to this
malloc address. But it is un-necessary for booting
from RAM.
This patch improves this flow by declare the
board_spl_fit_buffer_addr() to replace the original one.
The larger image size (eq: Kernel Image 10~20MB), it
can save more booting time.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
CCTL operations are available to Supervisor/User-mode
software under the control of the mcache_ctl.CCTL_SUEN
control bit. Enable it to support Supervisor(and User)
CCTL operations.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Priv ISA states:
"In systems without U-mode, the mcounteren register should
not exist."
Check U-Mode is present in MISA before writing to counteren, otherwise
we endup with Illegal Instruction exception on systems without U-Mode.
Also make checking MISA default for M-Mode.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Unlike in Linux, -supply is not automatically appended to regulator
requests. Add it.
Fixes: 2645bc0e12 ("arm: layerscape: Add sfp driver")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To improve startup times when booting from QSPI flash, the QSPI frequency
can be configured very early in the boot process [1] to reduce loading
times of U-Boot itself. This patch adds an option to disable setting the
frequency to a default value during SoC initialization.
[1] https://www.nxp.com/docs/en/application-note/AN12279.pdf
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/qoriq/qoriq-components/rcw:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP RCW github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
NXP tested imx8mn-ddr4 with firmware version 201810 only. Use this
version for all imx8mn targets with DRAM DDR4.
Fixes: 93c4c0e4dd ("arm: dts: imx8mn-u-boot: Create common imx8mn-u-boot.dtsi")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The 'commit 864ac2cf38 ("board: imx8mp: Add Engicam
i.Core MX8M Plus EDIMM2.2 Starter Kit")' has changed the imx8mp evk ram
settings from 6GB ram to 2GB.
This changeset reverts the above change.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reported-by : Peter Bergin <peter@berginkonsult.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
When routing UART4 using the ECSPI2 pads, register
IOMUXC_UART4_RXD_SELECT_INPUT (offset 0x050C) should be changed only
when dealing with RX, as its name suggests.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
SCFW has fixed a overflow issue in sc_rm_is_pad_owned API. This
requires u-boot to update API implementation, since it will cause
compatible issue. Otherwise all pad checking will have problem and
cause pad setting not continue.
Due to the compatible issue, the new u-boot only works with new
SCFW (API version: 1.21 and later).
old scfw + old u-boot: API overflow issue
old scfw + new u-boot, or new scfw + old u-boot: API compatible issue
new scfw + new u-boot: Working
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Jason Liu <Jason.hui.liu@nxp.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The imx8mn-beacon SOM has a QSPI part on it connected to the
FlexSPI controller. Add a defconfig option which supports
booting from the QSPI NOR flash instead of sd/mmc.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
In some situations the GSC firmware where the EEPROM containing the
model and DRAM configuration may not be ready by the time the SoC
is ready to talk to it over I2C.
Instead of a hard delay, poll the I2C lines to wait until they are
released to avoid the I2C drivers 'Arbitation lost' error message.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add I2C GPIO bus recovery support by adding scl-gpios and sda-gpios for the
various I2C busses on Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/imx/imx-atf:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP ATF github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cleanup some dangling comments left by automated migration
processes that are no longer value.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Synchronizing the device tree with linux introduced a regression.
The U-Boot specific dtsi mustn't override the alias settings for
the eMMC/SD interfaces.
Without this U-Boot cannot access the eMMC and boot the kernel.
Fixes: c21b61bff1 ("colibri-imx6ull/-emmc: synchronise device tree with linux")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
All Apalis iMX8 variants have 2nd RGMII on SoC, so add the address
for 2nd ethernet.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Implement basic PSCI provider to let OS turn CPU cores off and on,
power off and restart the system and determine PSCI version. This
is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following Kconfig options:
# CONFIG_PSCI_RESET is not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=y
CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y
CONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4
CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is the PSCI provider, it is necessary to correctly
program CSU and TZASC registers. Those are poorly documented, so
push in the correct values.
Signed-off-by: Marek Vasut <marex@denx.de>
The common code used to bring up secondary cores requires a final
jump location to be stored in some sort of memory location, define
this memory location to be the start of OCRAM, since it is available.
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is a PSCI provider, map RAM explicitly as NS,
otherwise secondary cores crash with SError when attempting
to access RAM mapped as secure in EL2.
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM pointers are in fact populated by the ATF BL31 blob, in case
U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence
ignore the ROM pointers.
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot itself if the PSCI provider on i.MX8M, do not
require the ATF BL31 blob, as at that point the blob is useless
and would interfere with U-Boot operation.
Signed-off-by: Marek Vasut <marex@denx.de>
The custom lowlevel_init implementation is no longer necessary, since
it is responsible for routing and trapping SErrors in U-Boot in EL2,
which is implemented in common code since commit:
6c7691edd5 ("armv8: Always unmask SErrors")
Signed-off-by: Marek Vasut <marex@denx.de>
The RESET2 hook is a PSCI v1.1 functionality, rename the macro accordinly.
Add missing handler for the RESET2 hook, so it can be implemented by U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
In commit d0399a46e7, the device tree was
synchronized from linux and the aliases were dropped.
They need to be kept so that the mmc cards are in the right order.
Without the aliases, u-boot reports:
MMC: FSL_SDHC: 2, FSL_SDHC: 3
With the aliases, u-boot reports:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
The upstream linux device tree does not contain the same aliases than
u-boot (It keeps the devices order with /dev/mmcblk2 and /dev/mmcblk3).
Because this board has been using different aliases in u-boot
and linux, a imx6q-sabrelite-u-boot.dtsi file is added to be
automatically included in imx6q-sabrelite.dts.
This way, linux and u-boot each keep their own aliases and there
is no breakage on current installations.
This should never be done for new boards as we want to keep linux and
u-boot with the same aliases as much as possible.
This patch is only necessary to avoid breaking existing setups.
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The introduction of CONFIG_FSL_QSPI_AHB_FULL_MAP as default in:
def88bce09 ("spi: fsl_qspi: Support to use full AHB space on i.MX")
broke the SPI NAND read access on the Kontron SL i.MX6UL/ULL boards.
Reading data from the flash returns garbage instead of the actual
content. Fix this for now by disabling the introduced option.
In the long run this should be fixed globally.
Fixes: def88bce09 ("spi: fsl_qspi: Support to use full AHB space on i.MX")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The highest register on ACT8846 is 0xf5, so set the number of registers
to 0xf6, ensuring that the pmic read/write commands are able to access
all of the supported registers (and many that are not valid, since the
register space is quite sparse).
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for HS400 in mode2timing array.
Add a quirk for Versal NET platform to indicate that HS400 is supported
through bit63 of capability register.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
HS400 is indicated in bit63 of capability register in few IP's.
Add a quirk to check this and add HS400 to host capabilities.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Check if the low level driver supports config_dll callback function and
call it if it does. Call with dll disable before calling set_clock and
with dll enable after it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>