Use "setter" functions instead of flags, cleaner and more flexible.
It also fixes the problem noted by Timur Tabi that the ethernet MAC
addresses were all being set incorrectly to the same MAC address.
The config value for:
* CFG_ACR_PIPE_DEP
* CFG_ACR_RPTCNT
* CFG_SPCR_TSEC1EP
* CFG_SPCR_TSEC2EP
* CFG_SCCR_TSEC1CM
* CFG_SCCR_TSEC2CM
Were not being used when setting the appropriate register
Added:
* CFG_SCCR_USBMPHCM
* CFG_SCCR_USBDRCM
* CFG_SCCR_PCICM
* CFG_SCCR_ENCCM
To allow full config of the SCCR.
Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349
that were just bogus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, this patch
updates ftp_cpu_setup() to write the MAC address to mac-address if it exists.
This function already updates local-mac-address.
Signed-off-by: Timur Tabi <timur@freescale.com>
The code supply fixed and SPD initialization for MPC83xx DDR2 Controller.
it pass DDR/DDR2 compliance tests.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8360E rev2.0 have new spridr,and PVR value,
The MDS board for MPC8360E rev2.0 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8349E rev3.1 have new spridr,and PVR value,
The MDS board for MPC8349E rev3.1 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo<X.Xie@freescale.com>
The code that is ifdef'd with CONFIG_MPC8349 is actually applicable to all
MPC834X class processors. Change the protections from CONFIG_MPC8349 to
CONFIG_MPC834X so they are more generic.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
Put the version (and magic) after the HRCW. This puts it in a fixed
location in flash, not at the start of flash but as close as we can get.
Signed-off-by: Jerry Van Baren <vanbaren@cideas.com>
For better format and style, I streamlined the 83xx head files,
including immap_83xx.h and mpc83xx.h. In the old head files, 1)
duplicated macro definition appear in the both files; 2) the structure
of QE immr is duplicated in the immap_83xx.h and immap_qe.h; 3) The
macro definition put inside the each structure. So, I cleaned up the
structure of QE immr from immap_83xx.h, deleted the duplicated stuff and
moved the macro definition to mpc83xx.h, Just like MPC8260.
CHANGELOG
*streamline the 83xx immr head file
Signed-off-by: Dave Liu <daveliu@freescale.com>
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
The 834x rev1.x silicon has one CPU5 errata.
The issue is when the data cache locked with
HID0[DLOCK], the dcbz instruction looks like no-op inst.
The right behavior of the data cache is when the data cache
Locked with HID0[DLOCK], the dcbz instruction allocates
new tags in cache.
The 834x rev3.0 and later and 8360 have not this bug inside.
So, when 834x rev3.0/8360 are working with ECC, the dcbz
instruction will corrupt the stack in cache, the processor will
checkstop reset.
However, the 834x rev1.x can work with ECC with these code,
because the sillicon has this cache bug. The dcbz will not
corrupt the stack in cache.
Really, it is the fault code running on fault sillicon.
This patch fix the incorrect dcbz operation. Instead of
CPU FP writing to initialise the ECC.
CHANGELOG:
* Fix the incorrect dcbz operation instead of CPU FP
writing to initialise the ECC memory. Otherwise, it
will corrupt the stack in cache, The processor will checkstop
reset.
Signed-off-by: Dave Liu <daveliu@freescale.com>
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
Hello,
Attached is a patch implementing multiple I2C buses on the MPC834x CPU
family and the MPC8349EMDS board in particular.
This patch requires Patch 1 (Add support for multiple I2C buses).
Testing was performed on a 533MHz board.
/*** Note: This patch replaces ticket DNX#2006083042000027 ***/
Signed-off-by: Ben Warren <bwarren@qstreams.com>
CHANGELOG:
Implemented driver-level code to support two I2C buses on the
MPC834x CPU family and the MPC8349EMDS board. Available I2C bus speeds
are 50kHz, 100kHz and 400kHz on each bus.
regards,
Ben
CHANGELOG:
* Errata DDR6, which affects all current MPC 834x processors, lists changes
required to maintain compatibility with various types of DDR memory. This
patch implements those changes.
Signed-off-by: Timur Tabi <timur@freescale.com>
CHANGELOG:
* On 83xx systems, use the CFG_FLASH_SIZE macro to program the LBC local access
window registers, instead of using a hard-coded value of 8MB.
Signed-off-by: Timur Tabi <timur@freescale.com>
Incorporated the common unified variable names and the changes in preparation
for releasing mpc8360 patches.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
- Removed MPC8349ADS port
- Added PCI support to MPC8349ADS
- reworked memory map to allow mapping of all regions with BATs
Patch by Kumar Gala 20 Apr 2006
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
