Most Chromebooks support chain-loading U-Boot but instructions are
somewhat scattered. Add a README to hold this information within the
U-Boot tree. Also add the standard developer keys to simplify the
instructions, since they are small.
For now this only supports nyan-big.
Signed-off-by: Simon Glass <sjg@chromium.org>
Send patch to Kever Yang instead of Lin Huang for Rockchip patches,
for Lin is not always working on upstream U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changed , to : in subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present lpe/lpss-sio/scc FSP properties are all boolean, but in
fact for "enable-lpe" it has 3 possible options. This adds macros
for these options and change the property from a boolean type to
an integer type, and change their names to explicitly indicate what
the property is really for.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce various meaningful macros for FSP settings and switch over
to use them instead of magic numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
"serial-debug-port-address" and "serial-debug-port-type" settings
are actually reserved in the FSP UPD data structure. Remove them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_JFFS2 for both the filesystem and its command, we
should have a separate option for each. This allows us to enable JFFS2
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far we were not using the FIT image format to its full potential:
The SPL FIT loader was just loading the first image from the /images
node plus one of the listed DTBs.
Now with the refactored loader code it's easy to load an arbitrary
number of images in addition to the two mentioned above.
As described in the FIT image source file format description, iterate
over all images listed at the "loadables" property in the configuration
node and load every image at its desired location.
This allows to load any kind of images:
- firmware images to execute before U-Boot proper (for instance
ARM Trusted Firmware (ATF))
- firmware images for management processors (SCP, arisc, ...)
- firmware images for devices like WiFi controllers
- bit files for FPGAs
- additional configuration data
- kernels and/or ramdisks
The actual usage of this feature would be platform and/or board specific.
Also update the FIT documentation to mention the new SPL feature and
provide an example .its file to demonstrate its features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lokesh Vutla <lokeshvuta@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that we have ACPI S3 support on Intel MinnowMax board, document
some generic information of S3 and how to test it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds documentation on the u-boot,spl-payload-offset property
(which overrides CONFIG_SYS_SPI_U_BOOT_OFFS during the SPI loading in
the SPL stage, if present).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
This driver is a simplified version of linux/drivers/leds/leds-bcm6358.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is a simplified version of linux/drivers/leds/leds-bcm6328.c,
simplified to remove HW leds and blink fallbacks.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In some boards like the Raspberry Pi the initial bootloader will pass
a DT to the kernel. When using U-Boot as such kernel, the board code in
U-Boot should be able to provide U-Boot with this, already assembled
device tree blob.
This patch introduces a new config option CONFIG_OF_BOARD to use instead
of CONFIG_OF_EMBED or CONFIG_OF_SEPARATE which will initialize the DT
from a board-specific funtion instead of bundling one with U-Boot or as
a separated file. This allows boards like the Raspberry Pi to reuse the
device tree passed from the bootcode.bin and start.elf firmware
files, including the run-time selected device tree overlays.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the steps to manually (re)build a Quartus FPGA project,
generate the required BSP glue, and update u-boot handoff files for
mainline SPL support. Requires Quartus toolchain and current U-Boot.
Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a section describing the secure boot image used on
Keystone2 secure devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sort rk3288 boards in alphabetical order.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 does not have any boot selection pins and the BootROM probes
the boot interfaces using the following boot-order:
1. SPI
2. eMMC (sdhci in DTS)
3. SD card (sdmmc in DTS)
4. USB loader
For ease of deployment, the SPL stage should mirror the boot order of
the ROM and use the same probing order (assuming that valid images can
be detected by SPL) unless instructed otherwise. The boot-order can
then be configured via the 'u-boot,spl-boot-order' property in the
chosen-node of the DTS.
While this approach is easily extensible to other boards, it is only
implemented for the RK3399 for now, as the large SRAM on the RK3399
makes this easy to fit the needed infrastructure into SPL and our
production setup already runs with DM, OF_CONTROL and BLK in SPL.
The new boot-order property is expected to be used in conjunction with
FIT images (and all legacy image formats disabled via Kconfig).
A boot-sequence with probing and fallthroughs from SPI via eMMC to SD
card (i.e. &spiflash, &sdhci, &sdmmc) has been validated on the RK3399-Q7.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Building sd images for rk3188 requires more steps due to the needed split
into TPL and SPL as loaders. Describe how to build an image for it in a
separate paragraph in the READER.rockchip file.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).
For this purpose we introduce a new phy-driver, called "Fixed PHY".
Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.
Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).
During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds documentation on the u-boot,efi-partition-entries-offset
property (which overrides CONFIG_EFI_PARTITION_ENTRIES_OFF, if
present).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves the description of the /config node from README.fdt-control
into a separate file doc/device-tree-bindings/config.txt.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
This driver uses the same pin control binding as that of linux, binding
document of this patch is copied from linux. One addition done is for
GPIO input and output mode configuration which was missing.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add basic clock driver support for stm32f7 to enable clocks required by
the peripherals.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RK3399 support DDR3, LPDDR3, DDR4 sdram, this patch is porting from
coreboot, support 4GB lpddr3 in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Right now the u-boot,dm-pre-reloc flag will make each marked node
always appear in both spl and tpl. But systems needing an additional
tpl might have special constraints for each, like the spl needing to
be very tiny.
So introduce two additional flags to mark nodes for only spl or tpl
environments and introduce a function dm_fdt_pre_reloc to automate
the necessary checks in code instances checking for pre-relocation
flags.
The behaviour of the original flag stays untouched and still marks
a node for both spl and tpl.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Since commit c0efc3140e ("ARM: uniphier: change CONFIG_SPL_PAD_TO
to 128KB"), the u-boot.bin should be burned at the offset 0x20000.
I missed to update README.uniphier in that commit. Now updating.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The patch implements secure booting for the mvebu architecture.
This includes:
- The addition of secure headers and all needed signatures and keys in
mkimage
- Commands capable of writing the board's efuses to both write the
needed cryptographic data and enable the secure booting mechanism
- The creation of convenience text files containing the necessary
commands to write the efuses
The KAK and CSK keys are expected to reside in the files kwb_kak.key and
kwb_csk.key (OpenSSL 2048 bit private keys) in the top-level directory.
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.
Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig. Almost all
of the defines will go away.
I see only two exceptions:
configs/blanche_defconfig
configs/sandbox_noblk_defconfig
They define CONFIG_GENERIC_MMC, but not CONFIG_MMC. Something
might be wrong with these two boards, so should be checked later.
Anyway, this is the output of the moveconfig tool.
This commit was created as follows:
[1] create a config entry in drivers/mmc/Kconfig
[2] tools/moveconfig.py -r HEAD GENERIC_MMC
[3] manual clean-up of garbage comments in doc/README.* and
include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Commit 6e1f4d2652 ("arm: imx-common: add SECURE_BOOT option to
Kconfig") moved the CONFIG_SECURE_BOOT option to Kconfig, so update
the mxc_hab README file to reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Move all of the status LED feature to drivers/led/Kconfig.
doc/README.LED updated to reflect the Kconfig implementation.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Add support for signing with the pkcs11 engine. This allows FIT images
to be signed with keys securely stored on a smartcard, hardware security
module, etc without exposing the keys.
Support for other engines can be added in the future by modifying
rsa_engine_get_pub_key() and rsa_engine_get_priv_key() to construct
correct key_id strings.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Enable support for loading a splash image from within a FIT image.
The image is assumed to be generated with mkimage -E flag to hold
the data external to the FIT.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Now that ethernet support works, it can be dropped from the rockchip
TODO
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all. Remove.
Also, clean-up the README.socfpga. CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c27269953b
("mmc: complete unfinished move of CONFIG_MMC"). I see no grep hit
for the others.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
First, update the code snippet referenced in the README file. And
since there are only two boards that override flash_cmd_reset(),
might as well show them both.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
To being able to sign created binaries, we need to know the HAB Blocks
for that image. Especially for the imximage type the HAB Blocks are
only available during creation of the image. We want to preserve the
information until we get to sign the files.
In the verbose case we still get them printed out instead of writing
to log files.
Cc: sbabic@denx.de
v2-Changes:
- No usage of MKIMAGEOUTPUT_$(@F) macro.
- Predefine default value /dev/null in every involved Makefile.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Przemyslaw didn't maintain the PMIC anymore.
Update the pmic maintainer from Przeymyslaw to me.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to handle enable-active-high DT property. This property is
used to drive the gpio controlling fixed regulator as active high when
claiming gpio line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix the MMU mapping for A8K device family:
- Separate A7K and A8K memory mappings
- Fix memory regions by including IO mapping for all
3 PCIe interfaces existing on each connected CP110 controller
Add A8K memory mapping documentation with all regions
configured by Marvell ATF.
Change-Id: I9c930569b1853900f5fba2d5db319b092cc7a2a6
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Add pin control nodes to APN806, CP-master, CP-slave and
Armada-7040 and Armada-8040 boards DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add a DM port of Marvell pin control driver.
The A8K SoC family contains several silicone dies interconnected
in a single package. Every die is normally equipped with its own
pin controller unit.
There are 2 pin controllers in A70x0 SoC and 3 in A80x0 SoC.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for mvebu bubt command for flash image
load, check and burn on boot device.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
With the acquisition of Altera by Intel, my Altera email may be going
away soon. Update the contact to a more reliable address.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add a README with a brief guide to porting i2c drivers over to use driver
model.
Add a timeline also. All I2C drivers should be converted by the end
of June 2017.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This is not used by any boards. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
Reviewed-by: Jagan Teki <jagan@openedev.com>
To help automate the loading of custom image types we add the ability
to define custom handlers for the loadable section types. When we find
a compatible type while loading a "loadable" image from a FIT image we
run its associated handlers to perform any additional steps needed for
loading this image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To be able to represent the skip-init platdata element with OF_CONTROL,
it needs to be read from the device tree as well and put into the platform data.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device tree support for the bcm283x mini-uart driver.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device tree support for the bcm2835 GPIO driver.
Signed-off-by: Fabian Vogt <fvogt@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
P2010 is a single-core version of P2020. There is no P2010 target
configured. Drop related macros. P2010 SoC is still supported.
Signed-off-by: York Sun <york.sun@nxp.com>
P1014 is a variant of P1010. There is no P1014 target configured.
Drop related macros. P1014 SoC is still supported.
Signed-off-by: York Sun <york.sun@nxp.com>
P1013 is a single-core version of P1022. There is no P1022 target
configured. Drop related macros. P1022 SoC is still supported.
Signed-off-by: York Sun <york.sun@nxp.com>
P1012 is a single-core version of P1021. There is no P1012 target
configured. Drop related macros. P1012 SoC is still supported.
Signed-off-by: York Sun <york.sun@nxp.com>
Add Jagan and Maxime as Maintainers for SUNXI
Signed-off-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now the flash params table as renamed to spi_flash_ids structure,
so rename the sf_params.c to spi_flash_ids.c and remove the legacy.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Enable this so that EFI applications (notably grub) can be run under U-Boot
on x86 platforms.
At present the 'hello world' EFI application is not supported for the
qemu-x86_efi_payload64 board. That board builds a payload consisting of a
64-bit header and a 32-bit U-Boot, which is incompatible with the way the
EFI loader builds its EFI application. The following error is obtained:
x86_64-linux-ld.bfd: i386 architecture of input file
`lib/efi_loader/helloworld.o' is incompatible with i386:x86-64 output
This could be corrected with additional Makefile rules. For now, this
feature is disabled for that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[agraf: drop hello kconfig bits]
Signed-off-by: Alexander Graf <agraf@suse.de>
It is useful to have a basic sanity check for EFI loader support. Add a
'bootefi hello' command which loads HelloWord.efi and runs it under U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Fix documentation, add unfulfilled kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which
supports multiple options for bus type, clocking and reset structure, and
feature list.
This patch imports the binding from the Linux kernel, including my V3
patch to extend the binding to cover the Tegra186, which is applied for
next-20160912. So far, my changes have been acked by Lars Persson, the
original author of the binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds -i option that allows specifying a ramdisk file to be added to the
FIT image when we are using the automatic FIT mode (no ITS file).
This makes adding Depthcharge support to LAVA much more convenient, as
no additional configuration files need to be kept around in the machine
that dispatches jobs to the boards.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Neil Williams <codehelp@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Rephrase the toolchains section. Leave only Linaro toolchains
since it is the most tested these days.
- Add build instruction for ARMv8 SoC boards
- Add information about "ddrmphy" command
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For some unknown reason, coreboot framebuffer driver never works on
QEMU since day 1. It seems the driver only works on real hardware.
Document this issue.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add device model enabled PMIC driver for Ricoh RN5T567 PMIC used
on Colibri iMX7.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This should be CONFIG_SYS_MAX_NAND_DEVICE. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This option is not used now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The only content of this file is CONFIG options which are no-longer present
in U-Boot. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This issue covered by this doc appears to be fixed, so let's remove the
README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
There appear to be neither implemented nor used. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a section describing the additional boot types used on AM33xx
secure devices.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
In both DOS and ISO partition tables the same code to create partition name
like "hda1" was repeated.
Code moved to into a new function part_set_generic_name() in part.c and optimized.
Added recognition of MMC and SD types, name is like "mmcsda1".
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add special target "mbr" (otherwise configurable via CONFIG_FASTBOOT_MBR_NAME)
to write MBR partition table.
Partitions are now searched using the generic function which finds any
partiiton by name. For MBR the partition names hda1, sda1, etc. are used.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch introduces support for building U-Boot to run on the MIPS
Boston development board. This is a board built around an FPGA & an
Intel EG20T Platform Controller Hub, used largely as part of the
development of new CPUs and their software support. It is essentially
the successor to the older MIPS Malta board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Use environment variable "kernel_addr_r" to indicate the location
in RAM where FIT image will be stored.
Use label command "kernel" to indicate which <path> the FIT image at.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
When enabling a fixed regulator, it may take some time to rise to the
correct voltage. If we do not delay here then subsequent operations
will fail.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This feature is not supported. Document this, and add some details on how it
might be implemented.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
UEFI is commonly used on x86. Add a reference to U-Boot's support for this
in the x86 README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The README indicates that this is not supported, but this is no-longer true.
Update the text to indicate this and describe the FIT changes required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The debug FSP image is bigger in size than the normal FSP image. This
patch adds a small description on how to use this FSP debug version
by changing CONFIG_FSP_ADDR.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Xtensa processor architecture is a configurable, extensible,
and synthesizable 32-bit RISC processor core provided by Cadence.
This is the first part of the basic architecture port with changes to
common files. The 'arch/xtensa' directory, and boards and additional
drivers will be in separate commits.
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bring in required device tree file and bindings from Linux.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
TI's PCF8575 is a 16-bit I2C GPIO expander.The device features a
16-bit quasi-bidirectional I/O ports. Each quasi-bidirectional I/O can
be used as an input or output without the use of a data-direction
control signal. The I/Os should be high before being used as inputs.
Read the device documentation for more details[1].
This driver is based on pcf857x driver available in Linux v4.7 kernel.
It supports basic reading and writing of gpio pins.
[1] http://www.ti.com/lit/ds/symlink/pcf8575.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
In Tegra186, the BPMP (Boot and Power Management Processor) owns certain
HW devices, such as the I2C controller for the power management I2C bus.
Software running on other CPUs must perform IPC to the BPMP in order to
execute transactions on that I2C bus. This binding describes an I2C bus
that is accessed in such a fashion.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The BPMP implements some services which must be represented by separate
nodes. For example, it can provide access to certain I2C controllers, and
the I2C bindings represent each I2C controller as a device tree node.
Update the binding to describe how the BPMP supports this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra BPMP (Boot and Power Management Processor) is a separate
auxiliary CPU embedded into Tegra to perform power management work, and
controls related features such as clocks, resets, power domains, PMIC I2C
bus, etc. These bindings dictate how to represent the BPMP in device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
It is confusing to mention MAKEALL when it is not the normal way of building
U-Boot anymore. Update the documentation to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.
If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.
Loading sequence after rework:
bootrom ==> spl ==> bootrom ==> u-boot
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip:
Signed-off-by: Simon Glass <sjg@chromium.org>
Booting a payload out of NAND FLASH from the SPL is a crux today, as
it requires hard partioned FLASH. Not a brilliant idea with the
reliability of todays NAND FLASH chips.
The upstream UBI + UBI fastmap implementation which is about to
brought to u-boot is too heavy weight for SPLs as it provides way more
functionality than needed for a SPL and does not even fit into the
restricted SPL areas which are loaded from the SoC boot ROM.
So this provides a fast and lightweight implementation of UBI scanning
and UBI fastmap attach. The scan and logical to physical block mapping
code is developed from scratch, while the fastmap implementation is
lifted from the linux kernel source and stripped down to fit the SPL
needs.
The text foot print on the board which I used for development is:
6854 0 0 6854 1abd
drivers/mtd/ubispl/built-in.o
Attaching a NAND chip with 4096 physical eraseblocks (4 blocks are
reserved for the SPL) takes:
In full scan mode: 1172ms
In fastmap mode: 95ms
The code requires quite some storage. The largest and unknown part of
it is the number of fastmap blocks to read. Therefor the data
structure is not put into the BSS. The code requires a pointer to free
memory handed in which is initialized by the UBI attach code itself.
See doc/README.ubispl for further information on how to use it.
This shares the ubi-media.h and crc32 implementation of drivers/mtd/ubi
There is no way to share the fastmap code, as UBISPL only utilizes the
slightly modified functions ubi_attach_fastmap() and ubi_scan_fastmap()
from the original kernel ubi fastmap implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds information regarding SPL handling validation process of main u-boot
image on power/mpc85xx and arm/layerscape platforms.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Revise the content based on the v2 additions. This is kept as a separate
patch to avoid confusing those who have already reviewed the v1 series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Adds information regarding SPL handling the loading and processing of
secured u-boot images as part of the second stage boot the SPL does.
Introduces the description of a new interface script in the TI SECDEV
Package which handles the creation and prep of secured binary images.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If MAC is directly connected to another MAC (like a switch for example)
we don't need to probe for a phy, autoneogation and so on. We simply
have to setup speed.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that platform-specific ACPI global NVS is added, pack it into
ACPI table and get its address fixed up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for standard type SCI (without FIFO) port.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
When building a FIT with external data (-E), U-Boot proper may require
absolute positioning for executing the external firmware. To acheive this
use the (-p) switch, which will replace the amended 'data-offset' with
'data-position' indicating the absolute position of external data.
It is considered an error if the requested absolute position overlaps with the
initial data required for the compact FIT.
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
DISTRO_DEFAULTS is intended to mirror / replace
include/config_distro_defaults.h.
The intend is for boards which include this file to select this from
their Kconfig files and when moving setting to Kconfig which are #define-ed
in config_distro_defaults.h to select this from DISTRO_DEFAULTS so that
boards which have selected DISTRO_DEFAULTS will keep the same configuration
as before without needing any defconfig file changes.
The initial list of selected things matches all settings recently removed
from config_distro_defaults.h because they have been converted to Kconfig,
with the exception of CMD_ELF and CMD_NET, which have a default of y, if
the default of these ever changes they should be selected by DISTRO_DEFAULTS
too.
For testing and example purposes this commit also converts ARCH_SUNXI
to use DISTRO_DEFAULT instead of selecting everything it needs itself.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some drivers are still directly accessing the chip->mtd field. Patch
them to use nand_to_mtd() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
nand torture currently works on exactly one nand block which is specified
by giving the byteoffset to the beginning of the block.
Extend this by allowing for a second parameter specifying the byte size
to be tested.
e.g.
==> nand torture 1000000
NAND torture: device 0 offset 0x1000000 size 0x20000 (block size 0x20000)
Passed: 1, failed: 0
==> nand torture 1000000 40000
NAND torture: device 0 offset 0x1000000 size 0x40000 (block size 0x20000)
Passed: 2, failed: 0
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
[scottwood: fix usage to show size as optional, and add misssing braces]
Signed-off-by: Scott Wood <oss@buserror.net>
A reset controller is a hardware module that controls reset signals that
affect other hardware modules or chips.
This patch defines a standard API that connects reset clients (i.e. the
drivers for devices affected by reset signals) to drivers for reset
controllers/providers. Initially, DT is the only supported method for
connecting the two.
The DT binding specification (reset.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/reset/reset.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This updates the device-tree-bindings doc for x86-pinctrl driver:
- clarify "gpio-offset" is required only when "mode-gpio" is set
- correct property name "pull-strength"
- use tab instead of space at several places
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
on the shc board we see when booting in net boot mode,
that the ROM bootloader sends "AM335x ROM" as
vendor-class-identifier. U-Boots doc says "DM814x ROM".
So, add the info to the doc, that there is also
"AM335x ROM" possible.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
Tegra186's GPIO controller register layout is significantly different from
previous chips, so add a new driver for it. In fact, there are two
different GPIO controllers in Tegra186 that share a similar register
layout, but very different port mapping. This driver covers both.
The DT binding is already present in the Linux kernel (in linux-next via
the Tegra tree so far).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # v1
Signed-off-by: Tom Warren <twarren@nvidia.com>
For odroid-c2 (arch-meson) for now disable designware eth as meson
now needs to do some harder GPIO work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
lib/efi_loader/efi_disk.c
Modified:
configs/odroid-c2_defconfig
Adds doc/README.ti-secure file to explain in generic terms
how boot images need to be created for secure devices from
Texas Instruments.
Specific details for creating secure boot images for the
AM43xx, DRA7xx and AM57xx secure devices from Texas
Instruments are also provided in the README file.
Secure devices require a security development package (SECDEV)
package that can be downloaded from:
http://www.ti.com/mysecuresoftware
Login is required and access is granted under appropriate NDA
and export control restrictions.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove the warning from the Makefile, since boards that do not use generic
board will no longer build. Also update documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
A mailbox is a hardware mechanism for transferring small message and/or
notifications between the CPU on which U-Boot runs and some other device
such as an auxilliary CPU running firmware or a hardware module.
This patch defines a standard API that connects mailbox clients to mailbox
providers (drivers). Initially, DT is the only supported method for
connecting the two.
The DT binding specification (mailbox.txt) was taken from Linux kernel
v4.5's Documentation/devicetree/bindings/mailbox/mailbox.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
This will allow a driver's bind function to use the driver data. One
example is the Tegra186 GPIO driver, which instantiates child devices
for each of its GPIO ports, yet supports two different HW instances each
with a different set of ports, and identified by the udevice_id .data
field.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the device tree bindings and the accompanying documentation
for the TI DP83867 Giga bit ethernet phy driver.
The original document was from:
[commit 2a10154abcb75ad0d7b6bfea6210ac743ec60897 from the Linux kernel]
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add FIT_FPGA_PROP that user can identify an optional
entry for fpga.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Windows might cache system information and only detect ACPI changes
if you modify the ACPI table versions.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As of now, U-Boot can support installing and booting Ubuntu/Windows
with the help of SeaBIOS. Update the documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Document how to make SeaBIOS load and run the VGA ROM of Intel
IGD device when loaded by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently U-Boot environment address is at offset 0x7fe00 of a 8MB
SPI flash. When creating a partial u-boot.rom image without flash
descriptor and ME firmware, U-Boot actually occupies the last 1MB
of the flash, and reprograming U-Boot causes previous environment
settings get lost which is not convenient during testing.
Adjust the environment address to 0x6ef000 instead (before the MRC
cache data region in the flash).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove ACPI from the TODO list and add a new section to document
current ACPI support in U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This updates the doc for the following places:
- Mention CRB for Bayley Bay
- Mention Congatec QEVAL 2.0 & conga-QA3/E3845
- Limit part of the QEMU paragraphs to 80 cols
- Correct some typos (drive, it's, Ubuntu)
- Add description for "console=ttyS0,115200"
- Remove CONFIG_BOOTDELAY description which is already
in x86-common.h
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default SCI is disabled after power on. ACTL is the register to
enable SCI and route it to PIC/APIC. To support both ACPI in PIC
mode and APIC mode, configure SCI to use IRQ9.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This patch add a compatible spi driver for ath79 series SOC.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add support for ar933x serial.
Signed-off-by: Wills Wang <wills.wang@live.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The getopt(3) optstring '-' is a GNU extension which is not available on BSD
systems like OS X.
Remove this dependency by implementing argument parsing in another way. This
will also change the lately introduced '-b' switch behaviour.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
