Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is a sync with kernel mainline dts.
The U-Boot eMMC does not need to care about the power for Rockchip
SoCs, because if the board is using eMMC, the power will default on
(for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
vcc5v0_host and usbhub_enable share gpio4 RK_PA3,
which is a problem during probing (the second probe
will trigger a -EBUSY, when trying to get the gpio handle).
An analysis of the situation shows, that both regulators
are actually describing the same supply.
This patch removes the (currenlty not successful probing)
regulator vcc5v0_host from the DTS and adds the pinctrl-*
setting to usbhub_enable.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Phiilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various
drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x
driver for Poplar platform, because the platform falls into the
following strategy category made by the commit.
Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Before the commit lands, Poplar platform works by statically declaring
pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set
in the driver. But since Poplar also supports device configuration from
device tree, the commit practically drops the flag for Poplar, and hence
breaks the platform from booting.
This patch changes platform code and device tree to initiate pl011
serial device from device tree rather than static declaration, so that
above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore
the reported boot failure gets fixed.
Reported-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fixes: 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers")
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When DM_USB is used, either the USB controllers are bound when the DTB
is parsed (when OF_CONTROL is enabled) or they are bound using the
U_BOOT_DEVICES() macro.
In the later case, the platform data is passed in a struct ti_musb_platdata
because it cannot be read from the DTB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
USB1 can be used by the romboot on all am4372 platforms to download a
firmware (SPL in our case).
It makes sense to enable USB1 in the SPL to download u-boot.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This file is used to override the values found in am4372.dtsi
Use it to fix the "compatible" options for the controllers used
to support the USB (parent bus and syscons).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present these parameters are hard-coded in the sdl interface code.
Allow them to be specified by the driver instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update sandbox's device tree and config to use driver model for sound. Use
the double buffer for sound output so that we don't need to wait for the
sound to complete before returning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow setting the i2s pinmux correctly on exyno5420 so that i2c can be
used on that SoC. Also rename EXYNOS_AUDSS to something consistent with
other naming.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current dev_read...() functions use s32 and u32 which are convenient
for device tree but not so useful for normal code, which often wants to
use normal integers for values.
Add a helper which supports returning an unsigned int. Also add signed
versions of the unsigned readers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use a single buffer for sound which means we cannot be
playing one sound while queueing up the next. This wouldn't matter except
that a long sound (more than a second) has to be created as a single
buffer, thus using a lot of memory. To better mimic what real sound
drivers do, add support for double buffering in sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s bus is commonly used with audio codecs. It provides a way to
stream digital data sychronously in both directions. U-Boot only supports
audio output, so this uclass is very simple, with a single tx_data()
method.
Add a uclass and a test for i2s.
Signed-off-by: Simon Glass <sjg@chromium.org>
An audio codec provides a way to convert digital data to sound and vice
versa. Add a simple uclass which just supports setting the parameters for
the codec.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot sound system provides basic support for beeping. At present it
does not use driver model, but it needs to be converted. Add an option to
enable driver model for sound. For now it is not connected to anything.
Future work will add drivers which use this option. It will then be
removed once everything is converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.
Signed-off-by: Felix Brack <fb@ltec.ch>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
Now that we have FAN53555 support, we can enable the regulators in our
DTS. To make these easier to identify on the U-Boot commandline, we
rename them to the names of the voltage rails they control.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRA7 platforms requires that the dtb used in the SPL really matches the
platform to have the best MMC performances.
To detect the board type/version an I2C EEPROM is read. This requires that
DM is initialized before the detection. As a consequence we must reset the
DM after the board detection is a new dtb would better match the platform.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. The goal is to eventually remove DM_I2C_COMPAT
when all I2C "clients" have been migrated to use the DM API.
This a step in that direction for the TI based platforms.
Build tested with buildman:
buildman -dle am33xx ti omap3 omap4 omap5 davinci keystone
boot tested with:
am335x_evm, am335x_boneblack, am335x_boneblack_vboot (DM version),
am57xx_evm, dra7xx_evm, k2g_evm, am437x_evm
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to use DM_I2C, we need to move the board detection after the
early SPL initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If DM_I2C is used , the I2C controllers must be registered as U_BOOT_DEVICE
because OF_CONTROL is not used in the SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
