With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Clear possible errors in MCSR resulting from data-eye-search.
If not done, then we could get an interrupt later on when
exceptions are enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
vxWorks expects in
TLB 0 a entry for the Machine Check interrupt
TLB 1 a entry for the RAM
TLB 2 a entry for the EBC
TLB 3 a entry for the boot flash
After changing the baudrate to 9600 I had no problems to boot the
vxWorks image as distributed by WindRiver (Revision 2.0/1 from
June 18, 2007)
Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Note: this patch changes the configuration of some GPIO registers:
Register Old Value New Value
--------------- ---------- ----------
DCR GPIO0_TCR 0x0000000F 0x0000F0CF
DCR GPIO0_TSRH 0x55005000 0x00000000
DCR GPIO1_TCR 0xC2000000 0xE2000000
DCR GPIO1_TSRL 0x0C000000 0x00200000
DCR GPIO1_ISR2L 0x00050000 0x00110000
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds the Denali SDRAM controller definitions to "ppc440.h".
It also fixes two typos in the definitions, so the board-specific
"sdram.h" files containing these definitions are also fixed to avoid
compiler warnings.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.
This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
The I2C bootstrap values that can be setup via the "bootstrap" command,
were setup incorrect regarding the generation of the internal sync PCI
clock. The values for PLB clock == 133MHz were slighly incorrect and the
values for PLB clock == 166MHz were totally incorrect. This could
lead to a hangup upon booting while PCI configuration scan.
This patch fixes this issue and configures valid PCI divisor values
for the sync PCI clock, with respect to the provided external async
PCI frequency.
Here the values of the formula in the chapter 14.2 "PCI clocking"
from the 440EPx users manual:
AsyncPCICLK - 1MHz <= SyncPCIClk <= (2 * AsyncPCIClk) - 1MHz
33MHz async PCI frequency:
PLB = 133:
=> 32 <= 44.3 <= 65 (div = 3)
PLB = 166:
=> 32 <= 55.3 <= 65 (div = 3)
66MHz async PCI frequency:
PLB = 133:
=> 65 <= 66.5 <= 132 (div = 2)
PLB = 166:
=> 65 <= 83 <= 132 (div = 2)
Signed-off-by: Stefan Roese <sr@denx.de>
The BCSR status bit for the 66MHz PCI operation was correctly
addressed (MSB/LSB problem). Now the correct currently setup
PCI frequency is displayed upon bootup.
This patch also fixes this problem on Rainier & Yellowstone, since these
boards use the same souce code as Sequoia & Yosemite do.
Signed-off-by: Stefan Roese <sr@denx.de>
The 440EPx has a problem when the PCI_CACHE_LINE_SIZE register is
set to non-zero, because it doesn't support MRM (memory-read-
multiple) correctly. We now added the possibility to configure
this register in the board config file, so that the default value
of 8 can be overridden.
Here the details of this patch:
o drivers_pci_auto.c: introduce CFG_PCI_CACHE_LINE_SIZE to allow
board-specific settings. As an example the sequoia board requires 0.
Idea from Stefan Roese <sr@denx.de>.
o board/amcc/sequoia/init.S: add a TLB mapping at 0xE8000000 for the
PCI IO-space. Obtained from Stefan Roese <sr@denx.de>.
o include/configs/sequoia.h: turn CONFIG_PCI_PNP back on and set
CFG_PCI_CACHE_LINE_SIZE to 0.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a board command to configure the I2C bootstrap EEPROM
values. Right now 533 and 667MHz are supported for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 533 nor ;to configure the board for 533MHz NOR booting
=> bootstrap 667 nand ;to configure the board for 667MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
This patch undoes the patch by Jeff Mann with commit-id ada4697d. As
suggested by AMCC it is not recommended to dynamically change the EBC
speed after bootup. So we undo this change to be on the safe side.
Signed-off-by: Stefan Roese <sr@denx.de>
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big
for the 4k NAND boot image so define bus_frequency to 133MHz here
which is save for the refresh counter setup.
Signed-off-by: Stefan Roese <sr@denx.de>
As provided by the AMCC applications team, this patch optimizes the
DDR2 setup for 166MHz bus speed. The values provided are also save
to use on a "normal" 133MHz PLB bus system. Only the refresh counter
setup has to be adjusted as done in this patch.
For this the NAND booting version had to include the "speed.c" file
from the cpu/ppc4xx directory. With this addition the NAND SPL image
will just fit into the 4kbytes of program space. gcc version 4.x as
provided with ELDK 4.x is needed to generate this optimized code.
Signed-off-by: Stefan Roese <sr@denx.de>
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
