Commit graph

497 commits

Author SHA1 Message Date
Simon Glass
691d719db7 common: Drop init.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
4d72caa5b9 common: Drop image.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Chen-Yu Tsai
533f2433ff sunxi: Add Libre Computer ALL-H5-CC H5 board
The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

  - Gigabit Ethernet via external RTL8211E Ethernet PHY
  - 16 MiB SPI NOR flash memory
  - PoE tap header
  - Line out jack removed

Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.

The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:13:55 +05:30
Chen-Yu Tsai
986b5e8c4a sunxi: Add Libre Computer ALL-H3-IT H5 board
The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

  - H2, H3, or H5 SoC from Allwinner
  - 2 DDR3 DRAM chips
  - Realtek RTL8821CU based WiFi module
  - 128 Mbit SPI-NOR flash
  - micro-SD card slot
  - micro HDMI video output
  - FPC connector for camera sensor module
  - generic Raspberri-Pi style 40 pin GPIO header
  - additional pin headers for extra USB host ports, ananlog audio and
    IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

The device tree was synced over from the Linux kernel, along with other
H3/H5 changes, in a previous patch. Thus only the defconfig and an entry
to the MAINTAINERS file is added.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: drop CONFIG_SYS_SPI_U_BOOT_OFFS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:09:47 +05:30
Simon Glass
29a4a9f105 common: Move hang() to the same header as panic()
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-24 23:06:49 +05:30
Simon Glass
91527c9a30 common: Move RAM-sizing functions to init.h
These functions relate to memory init so move them into the init
header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-24 23:06:49 +05:30
Diego Rondini
e7c15b7ab8 sun8i: h3: Support H3 variant of Orange Pi Zero Plus 2
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.

H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply

Sync dts from linux v5.2 commit:
"ARM: dts: sunxi: h3/h5: Remove stale pinctrl-names entry"
(sha1: 75f9a058838be9880afd75c4cb14e1bf4fe34a0b)
Commit:
"ARM: dts: sun8i: h3: Refactor the pinctrl node names"
(sha1: a4dc791974e568a15f7f37131729b1a6912f4811)
has been avoided as it breaks U-Boot build.

Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-12-18 20:14:16 +05:30
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Simon Glass
3db7110857 crc32: Use the crc.h header for crc functions
Drop inclusion of crc.h in common.h and use the correct header directly
instead.

With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:08 -05:00
Sunil Mohan Adapa
4ed293ae79 arm64: dts: sun50i: Add support for A64 OLinuXino (with eMMC)
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

The Linux kernel upstream has chosen to create and use a separate device tree
for the eMMC variants instead of adding eMMC support existing device tree. These
changes to Linux kernel are queued for Linux 5.4.

commit <02bb66b347ff8115f53948f86b884e008ba385b9> ("arm64: dts:
allwinner: a64: Add A64 OlinuXino board (with eMMC)")

This patch has been tested on A64-OLinuXino-1Ge16GW and is based on Linux
device-tree and a64-olinuxino_defconfig.

Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
[jagan: updated linux-next commit details]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 14:15:49 +05:30
Maxime Ripard
9bd9b2bcbe MAINTAINERS: Update my email address
I'm not at bootlin anymore, and my mail address doesn't work any longer.

Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-10-06 15:20:53 -04:00
Simon Glass
f3998fdc4d env: Rename environment.h to env_internal.h
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.

Rename this file and add a comment at the top to indicate its internal
nature.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-11 19:27:31 -04:00
Simon Glass
c7694dd483 env: Move env_set_hex() to env.h
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-08-11 16:43:41 -04:00
Marcus Cooper
a9e19b8ff7 sun8i: h3: Add support for the Beelink-x2 STB
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.

Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-15 12:25:32 +05:30
Jonas Smedegaard
997b857ae3 sun50i: a64: Add Olimex A64-Teres-I board initial support
Olimex A64-Teres-I board is a mainboard (the only one so far)
for Olimex Teres-I DIY laptop kit.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- MicroSD Slot
- 16GB eMMC Flash
- eDP LCD display
- HDMI
- USB Host
- Battery management
- 5V DC power supply
- Certified Open Source Hardware (OSHW)

Works:
- i2C
- MMC/SD
- PWM backlight

Known broken:
- Internal keyboard (seems to be because the keyboard firmware loads a
bootloader first, and then disconnects bootloader and connect real
keyboard). External ones connected to the USB port work fine.

This patch enables support for the A64-Teres-I board to u-boot,
including enabling screen backlight (lacking from Linux device-tree).

Linux commit details about the sun50i-a64-teres-i.dts sync:
"arm64: dts: allwinner: a64: Rename uart0_pins_a label to uart0_pb_pins"
(sha1: d91ebb95b96c8840932dc3a10c9f243712555467)

Cosmetic warnings regarding whitespace and placement of SPDX notice for
dts file was ignored.

config and .dtsi file are adapted from pinebook files.

Tested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: move board entry in MAINTAINERS file at proper position]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-09 00:44:13 +05:30
Clément Péron
517ee64205 arm: dts: h6: Add Beelink GS1 initial support
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)

Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-18 22:14:34 +05:30
Andre Przywara
f8c8669760 sunxi: update SATA driver to always use DM_SCSI
It seems like the Allwinner SATA driver is already quite capable of
using the driver model, so we can force this on all boards and can
remove support for a non-DM_SCSI build.
This removes the warning about boards with SATA ports not being
DM_SCSI compliant.

It also takes the opportunity to move the driver out of the board/sunxi
directory to join its siblings in drivers/ata, and to make it a proper
Kconfig citizen.

The board defconfigs stay untouched.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: select DM_SCSI separately]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 14:34:45 +05:30
Jagan Teki
cbb9cdc7aa board: sunxi: Add R40 sata compatible
Add sata compatible for R40.

Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 14:34:45 +05:30
Jagan Teki
99a8a3114f board: sunxi: gmac: Remove Ethernet clock and reset
Since Ethernet clock and reset is now handling via
CLK and RESET frameworks via driver API's remove
explicit ccm writes.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-16 16:29:01 +05:30
Tom Rini
216800acf1 Merge branch 'master' of git://git.denx.de/u-boot-spi
Conflicts:
	arch/arm/dts/armada-385-amc.dts
	arch/arm/dts/armada-xp-theadorable.dts
	arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-14 00:03:06 -04:00
Jagan Teki
59aea29a31 MAINTAINERS: Change Jagan's email address
Missed few mails from openedev, since most of the day I look at
amarulasolutions mail so update the same.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-12 18:47:16 +05:30
Jagan Teki
1692c73ccb sun50i: a64: Add Oceanic 5205 5inMFD initial support
Oceanic 5205 5inMFD is a 5 inch Multi function display baseboard
designed to mount SoPine SOM.

Key features:
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 2GB DDR3 RAM
- SD Slot
- SPI-NOR flash
- EMAC, RTL8211E
- MCP2515 CAN
- 4-lane, MIPI-DSI panel
- Goodix 911 CTP
- USB Host
- 12V DC power supply

Linux commit details about the sun50i-a64-oceanic-5205-5inmfd.dts sync:
"arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support"
(sha1: 00f7980a3bd53d12abc34f68146a8eed0e894248)

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-10 15:25:38 +05:30
Chen-Yu Tsai
da95ed58c4 sunxi: Add Bananapi M2+ H5 board
As the H5 is pin compatible with the H3, vendors tend to upgrade their
existing H3 products with an H5 SoC swap. This is the case with the
Bananapi M2+ H5.

Add the following to support it:

  - device tree file: synced from Linux v5.0-rc1,
  - defconfig: copy of bananapi_m2_plus_h3_defconfig with only SoC
	       family and default device tree file name changed
  - MAINTAINERS entry

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-18 14:46:53 +05:30
Chen-Yu Tsai
268ae65487 sunxi: Rename Sinovoip BPI M2 Plus to Bananapi M2 Plus H3
The brand Sinovoip is used for Sinovoip's original VOIP products, while
the Bananapi brand is for the single board computers they produce. This
has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
used.

To support the H5 variant of this board, the "H3" suffix is added to
the defconfig name.

Also add myself as one of the board maintainers.

As the device tree files were already correctly named, they do not
require any changes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[jagan: removed unneeded message from commit body]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-02-18 14:44:06 +05:30
Andre Przywara
a7ae159978 sunxi: board: do MMC pinmux setup for DM_MMC builds
Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.

However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.

When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.

Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-29 23:46:14 +05:30
Aleksandr Aleksandrov
7d659573ce board: sun50i-h5: Add Emlid Neutis N5 support
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.

- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board

Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-01-18 22:19:08 +05:30
Stefan Mavrodiev
da1ae5905e sunxi: board: Add i2c initialization for sun50i
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.

This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.

Tested with A64-SOM204 board.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-01-18 22:19:08 +05:30
From: Karl Palsson
44c214dc27 Revert "sunxi: board: Print error after power initialization fails"
Commit a8011eb84dfa("sunxi: board: Print error after power initialization
fails") moved the DRAM init after the increase of the CPU clock
frequency. This lead to various DRAM initialisation failures on some
boards (hangs or wrong size reported, on a NanoPi Duo2 and OrangePi
Zero, for instance). Lowering the CPU frequency significantly (for instance
to 408 MHz) seems to work around the problem, so this points to some timing
issues in the DRAM code.

Debugging this sounds like a larger job, so let's just revert this patch
to bring back those boards.
Beside this probably unintended change the patch just moved the error
message around, so reverting this is not a real loss.

This reverts commit a8011eb84d.

Tested-By: Priit Laes <plaes@plaes.org>
Signed-off-by: Karl Palsson <karlp@tweak.net.au>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-12-30 00:57:17 +05:30
Tom Rini
48d299a799 Merge branch 'master' of git://git.denx.de/u-boot-usb
- DWC3 and UDC cleanup
2018-12-10 07:15:12 -05:00
Philipp Tomsich
a740ee913e lib: merge CRC16-CCITT into u-boot/crc.h
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure.  Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-12-08 20:18:32 -05:00
Andre Przywara
8a6121ea07 sunxi: update README.sunxi64
Now that the Allwinner port in the official mainline ARM Trusted
Firmware repository has reached feature parity with the "legacy" ATF
port, let's use the opportunity to update the Allwinner 64-bit build
instructions. This changes:
- Update ATF build instructions to use the mainline repo.
- Add quick command lines for TL;DR people.
- Mention Allwinner H6 build target.
- Mention pre-built FEL binaries.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-12-07 22:30:19 +05:30
Olliver Schinagl
a8011eb84d sunxi: board: Print error after power initialization fails
Currently during init, we enable all power, then enable the dram and
after that check whether there was an error during power-up.

This makes little sense, we should enable power and then check if power
was brought up properly before we continue to initialize other things.

This patch moves the DRAM init after the power failure check.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-12-07 22:24:33 +05:30
Jean-Jacques Hiblot
0131162439 dm: usb: create a new UCLASS ID for USB gadget devices
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.

Also move the generic DM code for USB gadgets in a separate file for
clarity.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:45 +01:00
Tom Rini
ad890cace3 sunxi: Update MAINTAINERS file for recent boards
Add entries for the pine64-lts and pinebook configs.

Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-11-16 16:52:01 -05:00
Jagan Teki
e6b16e7852 board: allwinner: sun50i-h6: Add Orangepi Lite2 support
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-11-13 22:13:09 +05:30
Vasily Khoruzhick
31a4ac4d79 sun50i: A64: add support for R_I2C controller
Allwinner A64 has a I2C controller, which is in the R_ MMIO zone and has
two groups of pinmuxes on PL bank, so it's called R_I2C.

Add support for this I2C controller and the pinmux which doesn't conflict
with RSB.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-11-13 22:09:10 +05:30
Jun Nie
7bb0d212f2 sunxi: add support for Banana Pi M2 Zero board
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-10-31 12:13:02 +05:30
Andre Przywara
5776610e9e sunxi: store DRAM size in SPL header
At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.

As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.

Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Andre Przywara
cff5c13849 sunxi: board.c: refactor SPL header checks
So far we have two users which want to look at the SPL header. We will
get more in the future.
Refactor the existing SPL header checks into a common function, to
simplify reusing the code.
Now that this is easy, add proper version checks to the DT name parsing.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Andre Przywara
55d481d201 sunxi: Extend SPL header versioning
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.

Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.

[1] https://semver.org

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Icenowy Zheng
c6c2c85e4b sunxi: disable Pine A64 model detection code on other boards
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.

Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.

On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:07 +05:30
Priit Laes
df4ad94d05 sunxi: docs: Mention CONFIG_NAND requirement
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Priit Laes
297963f5b5 sunxi: Fix typos of spelling Allwinner
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-24 22:02:15 +05:30
Jagan Teki
d8024074e4 board: sunxi: Remove unused local variables
variables buf from board_mmc_init, and ret from misc_init_r
were unused on the functions, so remove it.

Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2018-08-20 18:10:43 +05:30
Jagan Teki
89a897fc4d board: sun50i: h6: Add OrangePi One Plus initial support
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-07-31 20:50:01 +05:30
Icenowy Zheng
a8407b5642 sunxi: add support for Pine H64 board
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.

Add support for it.

The device tree is from Linux next-20180720.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Icenowy Zheng
42956f1b85 sunxi: add MMC support for H6
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.

Add MMC support for H6. EMCE support is not added yet.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Icenowy Zheng
0a21fdd62b sunxi: change ATF position for H6
H6 has different SRAM A2 address, so the ATF load address is also
different.

Add judgment code to sunxi 64-bit FIT generation script. It will judge
the SoC by the device tree's name.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Hauke Mehrtens
76d69eb01d sun50i: h5: Add initial Orange Pi Zero Plus support
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.

H5 Orangepi Zero Plus has
 - Quad-core Cortex-A53
 - 512MB DDR3
 - micrSD slot
 - 16MBit SPI Nor flash
 - Debug TTL UART
 - 1GBit/s Ethernet (RTL8211E)
 - Wifi (RTL8189FTV)
 - USB 2.0 Host
 - USB 2.0 OTG + power supply

The device tree file is copied from the Linux kernel 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16 14:52:42 +05:30
Hauke Mehrtens
a6580dfd46 sun8i: h2: Add initial Orange Pi R1 support
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.

H2+ Orange Pi R1 has
 - Quad-core Cortex-A7
 - 256MB DDR3
 - micrSD slot
 - 128MBit SPI Nor flash
 - Debug TTL UART
 - 100MBit/s Ethernet (H2+)
 - 100MBit/s Ethernet (RTL8152B)
 - Wifi (RTL8189ETV)
 - USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.

The device tree file is copied from the Linux kernel 4.17.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-06-16 14:52:42 +05:30
Jagan Teki
2e8dbe14e7 board: sun50i: Add Amarula A64-Relic initial support
Amarula A64-Relic is A64 based IoT device, which support
- Allwinner A64 Cortex-A53
- Mali-400MP2 GPU
- AXP803 PMIC
- 1GB DDR3 RAM
- 8GB eMMC
- AP6330 Wifi/BLE
- MIPI-DSI
- CSI: OV5640 sensor
- USB OTG
- 12V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-06-04 18:09:25 +05:30
Jagan Teki
f5871a66fd sunxi: Drop legacy usb_phy.c
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
237050fc62 board: sunxi: Use generic-phy for board_usb_cable_connected
Allwinner PHY USB code is now part of generic-phy framework,
so use it in board_usb_cable_connected.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Tom Rini
e8f80a5a58 Merge git://git.denx.de/u-boot-sunxi 2018-05-09 12:58:06 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Jagan Teki
f3df7758b5 board: sunxi: sun8i-v40: Add Bananapi M2 Berry support
Banana Pi BPI-M2 Berry is a quad-core mini single board computer
built with Allwinner V40 SoC. It features
- Quad Core ARM Cortex A7 CPU V40
- 1GB of RAM .
- microSD/SATA port..
- onboard WiFi and BT
- 4 USB A 2.0 ports
- 1 USB OTG port
- 1 HDMI port
- 1 audio jack
- DC power port

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-05-07 11:33:19 +05:30
Chen-Yu Tsai
e9392b373a sunxi: Add Libre Computer Board ALL-H3-CC H5 ver.
This patch adds a device tree file for the H5 version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H5 SoC, and
has 4Gb DDR3 chips instead of 2Gb ones.

The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-01 10:15:58 +05:30
Chen-Yu Tsai
ad34951708 sunxi: Add Libre Computer Board ALL-H3-CC H2+ ver.
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H2+ SoC, and
has only two 2Gb DDR3 chips instead of four.

The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-05-01 10:15:58 +05:30
Andre Przywara
35debf8a45 sunxi: README.sunxi64: Add hint about non-debug of ARM Trusted Firmware
As we are running into issues where the final U-Boot FIT image file is
exceeding our size limit, add a hint to the README.sunxi64 file
to point out the possibility of building non-debug versions of the ATF
binary. These are about 12KB smaller than the standard debug build, and
so allow successful U-Boot builds for many boards with the Allwinner H5
SoC.
Please note that under normal circumstances the debug build is still
recommended, as it gives valuable clues in case something goes wrong in
the ATF.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04 11:31:35 +05:30
Miquel Raynal
136e325933
sunxi: spl: remove DMA related settings of the NAND controller
Code has been changed to do not use DMA anymore with the NAND
controller, instead PIO is used. Then, DMA-specific initialization may
be dropped.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:48 +02:00
Miquel Raynal
ba1c98bae2
sunxi: spl: deassert the NAND controller reset line
Ensure the NAND controller reset line is deasserted before use.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-04-03 12:11:32 +02:00
Stefan Mavrodiev
d682cff440 sunxi: Add A20-SOM204-EVB-eMMC board
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired
to MMC2 slot.

This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 22:40:35 +05:30
Stefan Mavrodiev
8dd6497d9c sunxi: Add A20-SOM204-EVB board
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.

Base features of A20-SOM204 board includes:
	* 1GB DDR3 RAM
	* AXP209 PMU
	* KSZ9031 Gigabit PHY
	* AT24C16 EEPROM
	* Status LED
	* LCD connector
	* GPIO connector

There will be variants with the following options:
	* Second LAN8710A Megabit PHY
	* 16MB SPI Flash memory
	* eMMC card
	* ATECC508 crypto device

The EVB board has:
	* Debug UART
	* MicroSD card connector
	* USB-OTG connector
	* Two USB host
	* RTL8723BS WiFi/BT combo
	* IrDA transceiver/receiver
	* HDMI connector
	* VGA connector
	* Megabit ethernet transceiver
	* Gigabit ethernet transceiver
	* SATA connector
	* CAN driver
	* CSI camera
	* MIC and HP connectors
	* PCIe x4 connector
	* USB3 connector
	* Two UEXT connectors
	* Two user LEDs

Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.

This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 22:38:58 +05:30
Tuomas Tynkkynen
b0b0d22f1a ARM: sunxi: Build u-boot-sunxi-with-spl.bin on ARM64 as well
In README.sunxi64 we tell the user how to optionally create
u-boot-sunxi-with-spl.bin by manually running cat. Instead, have the
build system create the file automatically just like it does for 32-bit
sunxi boards.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 20:36:51 +05:30
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Maxime Ripard
bf8f4c4400 MAINTAINERS: Update email address for Maxime Ripard
Free Electrons is no more and is now known as Bootlin, change my email
address accordingly.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-02-04 19:21:00 -05:00
Maxime Ripard
b39117cad9 sunxi: Transition from the MMC to a FAT-based environment
The current environment has been hardcoded to an offset that starts to be
an issue given the current size of our main U-Boot binary.

By implementing a custom environment location routine, we can always favor
the FAT-based environment, and fallback to the MMC if we don't find
something in the FAT partition. We also implement the same order when
saving the environment, so that hopefully we can slowly migrate the users
over to FAT-based environment and away from the raw MMC one.

Eventually, and hopefully before we reach that limit again, we will have
most of our users using that setup, and we'll be able to retire the raw
environment, and gain more room for the U-Boot binary.

Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2018-01-27 09:23:22 -05:00
Andre Przywara
8837af154c sunxi: arm64: correct usage of DT node address in FIT generation
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Adjust the FIT build script for 64-bit Allwinner boards to remove the
bogus addresses from the node names and avoid the warnings.
This avoids a warning with recent versions of the dtc tool.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2018-01-15 18:29:21 -07:00
Maxime Ripard
3afdfd8ddc sunxi: maintainers: Add myself for the TBS A711
Support for that board got introduced recently without the maintainers
part. Let's fix that.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2018-01-10 11:30:49 +05:30
Chen-Yu Tsai
afe2754412 sunxi: Add support for Libre Computer Board ALL-H3-CC H3 ver.
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.

Raspberry Pi B+ like peripherals supported on this board include:

  - Power input through micro-USB connector (without USB OTG)
  - Native 100 Mbps ethernet using the internal PHY, as opposed to
    USB-based on the RPi
  - 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
    being connected through a USB 2.0 hub on the RPi
  - TV and audio output on a 3.5mm TRRS jack
  - HDMI output
  - Micro-SD card slot
  - Standard RPi B+ GPIO header, with the standard peripherals routed to
    the same pins.

    * 5V, 3.3V power, and ground
    * I2C0 on the H3 is routed to I2C1 pins on the RPi header
    * I2C1 on the H3 is routed to I2C0 pins on the RPi header
    * UART1 on the H3 is routed to UART0 pins on the RPi header
    * SPI0 on the H3 is routed to SPI0 pins on the RPi header,
      with GPIO pin PA17 replacing the missing Chip Select 1
    * I2S1 on the H3 is routed to PCM pins on the RPi header

  - Additional peripherals from the H3 are available on different pins.
    These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3

In addition, there are a number of new features:

  - Console UART header
  - Consumer IR receiver
  - Camera interface (not compatible with RPi)
  - Onboard microphone
  - eMMC expansion module port
  - Heatsink mounting holes

This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.

Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2018-01-10 11:27:41 +05:30
Stefan Mavrodiev
aba3924927 sunxi: Fix A20-OLinuXino-MICRO LAN8710 support
>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-12-07 10:57:23 +05:30
Antony Antony
6130b1f6bc sun50i: h5: Add NanoPi Neo Plus2 DT initial support
Add initial DT for NanoPi NEO Plus2 by FriendlyARM
- Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
- 1 GB DDR3 RAM
- 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
- micro SD card slot
- Gigabit Ethernet (external RTL8211E-VB-CG chip)
- 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
- 2x USB 2.0 host ports

Signed-off-by: Antony Antony <antony@phenome.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-21 19:11:57 +05:30
Werner Böllmann
8e2c2d413c sunxi: SATA link timeout fix
After updating u-boot from v2016.01 to 2017.09, issue with
"SATA link 0 timeout." on my Cubietruck board.

mdelay milled after moving satapwr code to board.
"sunxi: Turn satapwr on from board_init"
(sha1: 9fbb0c3aa4)

After adding the "mdelay(500);"
line that was lost in the path the error is gone.

Signed-off-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
[Rebased and updated change and commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-10 19:21:24 +05:30
Tom Rini
79df00fdb4 MAINTAINERS: Add missing boards and config entries
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time.  As part of that, address a number of
missing MAINTAINERS entires.  In the case of a missing file, I have put
the original submitter down.  In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-06 09:58:51 -05:00
Icenowy Zheng
e6ee85a689 sunxi: only init USB Ethernet gadget when it's enabled
If the USB Ethernet gadget is not yet enabled, the call of
usb_ether_init in board/sunxi/board.c will lead to undefined reference
error when building.

Fix this problem.

Fixes: 50ddbf1199a0 ("sunxi: Register usb_ether")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Jagan Teki
ea5b1e1efb sun7i: a20: Add Bananapi M1 Plus support
Banana Pi M1 Plus is an open-source single-board computer
that adds more connectivity to the classic board using
Allwinner A20 SOC.

Bananapi M1-Plus features:
- A20 Dual-core 1.0GHz
- 1 GB DDR3 SDRAM
- MicroSD
- 10/100/1000 Ethernet RJ45
- WiFi b/g/n
- 5V DC Micro USB power-supply

For dts file,
Sync with Linux commit f92ca09("Merge branch 'akpm/master'").

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
de86fc3859 sunxi: Remove the MMC index hack
The current code, if there's both an eMMC and an MMC slot available on the
board, will swap the MMC indices based on whether we booted from the eMMC
or the MMC. This way, the MMC we're supposed to boot on will always have
the index 0.

However, this causes various issues, for example when using other
components that base their behaviour on the MMC index, such as fastboot.

Let's remove that hack, and take the opposite approach. The MMC will always
have the same index, but the bootcmd will pick the same device than the one
we booted from. This is done through the introduction of the mmc_bootdev
environment variable that will be filled by the board code based on the
boot device informations we can get from the SoC.

In order to not introduce regressions, we also need to adjust the fastboot
MMC device and the environment device in order to set it to the eMMC, over
the MMC, like it used to be the case.

Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
f4c3523c98 sunxi: Use sunxi_get_boot_device
Our current board code duplicates a bit the sunxi_get_boot_device logic.
Now that we can use that function in the full-flavoured U-Boot, remove that
duplication and call the function instead.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Maxime Ripard
90dd2f19d6 sunxi: Register usb_ether
Call the function to register the usb_ether gadget in the board.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Maxime Ripard
3a61b080ac musb: sunxi: switch to the device model
The device model was implemented so far using a hook that needed to be
called from the board support, without DT support and only for the host.

Switch to probing both in peripheral and host mode through the DT.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Dave Prue
6ff005cf19 sunxi: Fix CONFIG_SUNXI_GMAC references
SUNXI_GMAC was still used to configure the code where as the
same has been renamed and moved to Kconfig in below commit
"sunxi: Move SUNXI_GMAC to Kconfig"
(sha1: 4d43d065db)

Signed-off-by: Dave Prue <dave@prue.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
[Tweek commit message, config_whitelist.txt, build-whitelist.sh]
Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-09-01 20:48:27 +05:30
Tom Rini
ceff355a5f Merge git://git.denx.de/u-boot-sunxi
Update A20-OLinuXino-Lime2-eMMC_defconfig to include CONFIG_SCSI

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:40 -04:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Simon Glass
fd1e959e91 env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()
Rename this function for consistency with env_set().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:56 -04:00
Simon Glass
018f530323 env: Rename common functions related to setenv()
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:32 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Jagan Teki
585bf8ae6f sun50i: a64: Add A64-OLinuXino initial support
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.

OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply

Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-15 11:30:59 +05:30
Jagan Teki
f322657204 sun50i: a64: Add initial NanoPi A64 support
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.

Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-08-15 11:30:19 +05:30
Olliver Schinagl
335d30050b sun7i: Add support for Olimex A20-OLinuXino-LIME2-eMMC
This patch adds support for the Olimex OLinuXino Lime2 with eMMC flash
storage.
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME2-eMMC/

It is a assembly variant of the regular Lime2 but featuring eMMC for
storage.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-11 15:16:39 +05:30
Simon Glass
cf7b2e10c9 dm: sata: sunxi: Add support for driver model
Adjust SATA setup to support driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-01 11:58:01 +09:00
Simon Glass
74daf94a23 dm: sunxi: sata: Don't build sata support into SPL
This is not used in SPL so we do not need to compile it. Make this change
before adding driver-model support to the driver, to avoid build errors.
With driver model we define a U_BOOT_DRIVER() which would otherwise be
present in SPL and not be garbage-collected when building.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-01 11:58:01 +09:00
Jagan Teki
2b1a33213e sun50i: h5: Add initial NanoPi NEO2 support
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.

NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-14 20:25:56 +05:30
Jagan Teki
bdf9577355 sun50i: a64: Add initial Orangepi Win/WinPlus support
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.

A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-14 15:58:39 +05:30
Jagan Teki
d6b1d7d81b sun50i: h5: Add initial Orangepi Zero Plus 2 support
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-14 15:52:19 +05:30
Icenowy Zheng
84580628b8 sunxi: add a defconfig for SoPine w/ official baseboard
The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).

The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.

Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 22:37:55 +05:30
Jagan Teki
b0174c39b3 sun8i: h3: Add initial NanoPi M1 Plus support
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.

NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-08 21:48:23 +05:30
Simon Glass
5d9828563f arm: Include asm/setup.h explictly
Include this header where needed so we do not need to rely on common.h.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-05 11:02:37 -04:00
Jagan Teki
868e37159e sun50i: h5: Add initial Orangepi Prime support
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.

H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT

Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology

CPU:   Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   phy interface7
eth0: ethernet@1c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-02 13:28:07 +00:00
Jagan Teki
2dbe9c1362 sun50i: a64: Add initial Banana Pi M64 support
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.

BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply

For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").

Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE:  BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE:  Configuring SPC Controller
NOTICE:  BL3-1: v1.0(debug):aa75c8d
NOTICE:  BL3-1: Built : 18:28:27, May 24 2017
NOTICE:  Configuring AXP PMIC
NOTICE:  PMIC: setup successful
INFO:    BL3-1: Initializing runtime services
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9

U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology

CPU:   Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM:  2 GiB
MMC:   SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot:  0

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-06-01 09:26:05 +00:00
Mylene JOSSERAND
a647ea172a sunxi: Add support for NanoPi M1
NanoPi M1 is a board based on Allwinner H3 CPU.

This commit adds the support for this platform with:
   - an include device tree which enables UART, LEDs, GPIO key switch,
   1 USB host ports and the SD-card as a dtsi file.
   - a device tree specific to this board that enables the
   2 additional USB ports
   - a defconfig file for minimal support
   - a section in MAINTAINERS (add myself)

Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-30 11:05:09 +05:30