As seen with codesourcery compiler 2010q1, the buf pointer in
usb_request structure is not aligned on 4 bytes boundary causing
data aborts in eth_setup -> conf_buf -> usb_gadget_config_buf.
Make it as align access to fix this issue.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
[voice.shen@atmel.com: add commit message]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
As seen on GCC 4.6 Linaro compiler, control_req buffer is not aligned
on 4 byte boundaray causing data aborts in eth_setup -> conf_buf
during dhcp boot over usb_ether. Fix the issue my aligning control_req
buffer using DEFINE_CACHE_ALIGN_BUFFER.
Tested on am335x_evm platform (beaglebone).
Applies on 2013.10-rc1 branch.
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Joel Fernandes <joelf@ti.com>
This patch makes required changes to make use
of I2S0 channel instead of I2S1 channel on exynos5250.
Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
This patch makes the necessary changes for making use of
I2S0 channel instead of I2S1 channel on smdk board. This
changes are done to maintain the uniformity to use I2S0 channel.
Signed-off-by: Dani Krishna Mohan <krishna.md@samsung.com>
if phy_connect() did not find a phy, phydev is NULL and
following code in cpsw_phy_init() crashes. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
The patch fixes the improper read and write of sdhci
host control register for sdma transfer.
The problem comes when reading and writing 1 byte long
host control register with the sdhci_readl() and
sdhci_writel(). The misuse of these functions overwrite
the value of the next registers which are in 4 bytes boundary.
This patch replaces four byte register read/write functions
with one byte read/write ones. Beside, it eliminates
unnecessary bit operation. i.e. or-ing zero against a variable.
Signed-off-by: Juhyun (Justin) Oh <Juhyun_Oh@sigmadesigns.com>
This fixes two issues:
* a descriptor was allocated for every block, while a descriptor can
take 8 blocks
* there was an off-by-one error in the descriptor preparation: there
were two last descriptors, one with length==0
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
In dwmci_prepare_data, the descriptors are allocated for DMA transfer.
These are allocated using the ALLOC_CACHE_ALIGN_BUFFER. This macro uses
the stack to allocate these descriptors. This becomes a problem if the
DMA transfer continues after the processor leaves the function in which
the descriptors were allocated.
Therefore, I have moved the allocated of the buffers up one level, to
dwmci_send_cmd(). The DMA transfer should be complete when leaving this
function.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
For SPL builds this is just dead code since we'll only need to read.
Eliminating it results in a significant size reduction for the SPL
binary, which may be critical for certain platforms where the binary
size is highly constrained.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Performing tftp transfers on mx28 results in random timeouts.
Hector Palacios and Robert Hodaszi analyzed the root cause being related to the
wrong alignment of the 'buff' buffer inside fec_recv().
Benoît Thébaudeau provided an excellent analysis of the alignment bug that is
present on older versions, such as GCC 4.5.4:
http://marc.info/?l=u-boot&m=137942904906131&w=2
Use ALLOC_CACHE_ALIGN_BUFFER() to avoid alignment issues from older GCC
versions.
Reported-by: Hector Palacios <hector.palacios@digi.com>
Tested-by: Oliver Metz <oliver@freetz.org>
Tested-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Similarly as mx25 and mx53, mx6solo-lite needs to setup the MII gasket for RMII
mode.
Add support for mx6solo-lite.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a driver for the TPS65910 PMIC that is found in the AM335x GP EVM,
AM335x EVM SK and others.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
[trini: Split and rework Avinash's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a driver for the TPS65217 PMIC that is found in the Beaglebone
family of boards.
Signed-off-by: Greg Guyotte <gguyotte@ti.com>
[trini: Split and rework Greg's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling s3c44b0_rtc.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling serial_s3c44b0.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling s3c44b0_i2c.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
Acked-by: Heiko Schocher <hs@denx.de>
If we don't have CONFIG_SPL_LIBCOMMON_SUPPORT defined then stdio
& *printf functions are unavailable & calling them will cause a link
failure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enable 8-bit host capability for HSMMC2 and/or HSMMC3. CONFIG_HSMMC2_8BIT
(for OMAP4/5/DRA7xx) and/or CONFIG_HSMMC3_8BIT (for DRA7xx only) must be
defined in the board header if an 8-bit eMMC device is connected to the
corresponding port.
Fix the "No status update" error that appeared for eMMC devices by
inserting a 20 us delay between writing arguments and command. This
solution has been proposed by Michael Cashwell <mboards@prograde.net>.
A minor cosmetic fix in a comment as well.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
"mmc_send_cmd: timeout: No status update" error sometimes happens in
omap_hsmmc driver func mmc_send_cmd() when the MMC controller card
identification and selection sequence is executed for eMMC on OMAP4
boards.
It happens due to incorrect execution of CMD line reset procedure
for OMAP4. Because CMD(DAT) lines reset procedures are slightly
different for OMAP3 and OMAP4(AM335x,OMAP5,DRA7xx).
According to OMAP3 TRM:
Set SRC(SRD) bit in MMCHS_SYSCTL register to 0x1 and wait until
it returns to 0x0.
According to OMAP4(AM335x,OMAP5,DRA7xx) TRMs, CMD(DATA) lines reset
procedure steps must be as follows:
1. Initiate CMD(DAT) line reset by writing 0x1 to SRC(SRD) bit in
MMCHS_SYSCTL register (SD_SYSCTL for AM335x).
2. Poll the SRC(SRD) bit until it is set to 0x1.
3. Wait until the SRC(SRD) bit returns to 0x0
(reset procedure is completed).
Unfortunately, at present omap_hsmmc driver has support only for
OMAP3. And as result step #2 is missing for OMAP4(AM335x,OMAP5,DRA7xx).
This sometimes leads to the fact that the waiting loop which is
required in step #3 does not executed, because SRC bit does not set
yet (at the moment of checking a condition of a loop execution).
And as a result this can cause to timeout error when sending a
next command.
In the particular case (working with eMMC witch do not respond to
some SD specific command) due to incorrect reset sequence after
command SD_CMD_SEND_IF_COND which finished with CTO flag within
64 clock cycles, the next command MMC_CMD_APP_CMD leads to a
timeout error within 1s.
So, extend CMD(DATA) lines reset procedure in func
mmc_reset_controller_fsm() by adding the missing step #2 for
OMAP4+/AM335x boards.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Do not call a memset for unused variable backup every time.
Remove unused variable from function.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
On a board with an i.mx28 and a Micron MT29F4G08ABAEAH4, Linux says:
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAH4),
512MiB, page size: 4096, OOB size: 224) the ECC strength is 16.
root@(none):/sys/devices/virtual/mtd/mtd0# for i in ecc_strength oobsize subpagesize; do echo $i = `cat $i`; done
ecc_strength = 16
oobsize = 224
subpagesize = 4096
The ECC strength was not properly discovered by U-Boot causing the data
written by Linux to return an -74 (EBADMSG) when read from U-Boot. This
patch fixes mxs_nand_get_ecc_strength() to function in case of a NAND
flash with page_data_size = 4096 and page_oob_size= 224.
Signed-off-by: Elie De Brauwer <eliedebrauwer@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.
This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
Based on Linux libata code, most drives are less than 10 sec, but some
need up to 20 sec.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
Some Intel SSDs can send a COMINIT after the initial COMRESET. This causes
the link to go down and we need to re-initialize the link.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Move the link bring-up handling to a separate weak function in order to
allow platforms to override it. This is needed on highbank platform which
needs special phy handling.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
gcc 4.7 will generate unaligned accesses to local char arrays, so make
them static to avoid that.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
The AHCI driver was incorrectly using the Capabilities register NP (number
of ports) field to determine which ports to activate. This commit changes
it to correctly use the PORTS_IMPL register as a port map.
Signed-off-by: Richard Gibbs <richard.gibbs@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
The PMECC use BCH algorithm to correct error. In BCH algorithm, the
primitive polynomial value is GF(2^13) for 512-bytes sector size. And it is
GF(2^14) for 1024-bytes sector size.
This patch will choose correct degree of the remainders (13 or 14) for
different sector size.
Tested in AT91SAM9X5-EK with MLC nand flash.
More detail can be refered to section 5.4.1 of:
AT91SAM ARM-based Embedded MPU Application Note
<http://www.atmel.com/Images/doc11127.pdf>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch add new functions to pmic max77686 to set voltage and mode.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The chipselect must be written into the CTRL0 register after the SSP
block is reset, otherwise the block will always use ChipSelect #0.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The 'enable' argument can be better expressed as boolean.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Currently we have the following behavior in ehci_hcd_init()
- Read csmr1 register, clear bit 26 and then set bit 26.
However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The manufacturer and product IDs are dynamically assigned when gadget is
bind.
Now the IDs aren't assigned at struct g_dnl_string_defs definition.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
USB composite gadget (g_dnl) supports only one configuration. Due to that
the corresponding field - bConfigurationValue has been changed.
Moreover more descriptive names were chosen for relevant fields.
Windows XP setup:
- Thesyscon USB Descriptor Dumper
- zadig_xp program for WinUSB installation (which is required by dfu-util)
- dfu-util for windows (version 0.6)
- TRATS target connected via USB hub to test Win XP machine.
Tested at: Trats - Exynos4210
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Egli, Samuel" <samuel.egli@siemens.com>
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Enable support for high-capacity eMMC and MMC cards. The MXS MMC
driver has no problem with those.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Amaury Pouly <amaury.pouly@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
add gpio common API support for gpio command
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[fix unnecessary cast]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix code to use pointer for pio port as the warning message suggested
remove the warning message
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
ecc minimum requirement in ONFI parameter.
a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
Driver will display a WARNING if the values are different from ONFI
parameters.
b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
the value from ONFI parameters.
* If ONFI ECC parameters are in ONFI extended parameter page, since we
are not support it, so assume the minimum ecc requirement is 2 bits
in 512 bytes.
* For non-ONFI support nand flash, also assume the minimum ecc
requirement is 2 bits in 512 bytes.
2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
and CONFIG_PMECC_SECTOR_SIZE.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
In this way, the pmecc corraction capbility can change in run time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since kernel code current use many dev_xxx() instead of using printk. To
compatible, move those dev_xxx from usb driver to linux/compat.h. Then all
driver code can use dev_err, dev_info and dev_vdbg.
This patch also removed duplicated macro definitions in usb driver.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
fix the following building warning
---8>---
macb.c: In function 'macb_init':
macb.c:400:14: warning: 'phydev' may be used uninitialized in this function
macb.c:377:21: note: 'phydev' was declared here
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Without this change, the following message is generated:
Warning: FEC using MAC address from net device
See doc/README.enetaddr for details.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions.
because of this code checkpatch script generates "WARNING: Avoid CamelCase".
Convert variables name to normal naming convention and modify board, driver
files with updated the new structure.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
After introduction of unified i2c model, the I2C_SET_BUS() macro is regarded
as obsolete.
Hence it is replaced with i2c_set_bus_num() function call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files: the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.
Insert a GPL-2.0 SPDX-License-Identifier to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
1. Reformat tx/rx descriptor as an uniform struct.
2. Replace uint32_t[2] with uint64_t for descriptor control.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.
To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch adds support for the SMSC9500 with product id 0x9900 which is
equipped in the "EXSYS USB 2.0" etherner USB adapter.
Tested on omap3_beagle.
Signed-off-by: Stefan Roese <sr@denx.de>
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Use default_serial_puts() instead of its own implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
There are many musb prints in SPL and U-Boot log.
These prints are required only during musb debug.
So replacing printk with pr_debug in musb_core.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tegra recently moved to the new I2C framework, which sets up I2C prior to
relocation, and prior to calling i2c_init_board(). This causes a crash on
Tegra boards.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Register arm_dcc with drivers/serial/serial.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removed stdio structure ops support on arm_dcc
driver, and need to register with serial core
so-that it can access like remianing serial drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch have changed mipi dsi write functions' parameters correctly
so that type cast operations were removed. And mipi dsi payload is
composed with array of panel commands to improve readability.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Some versions of the Zynq first stage boot loader enable PCAP loopback
during boot regardless of whether or not the boot image includes PL
configuration. This behavior only appears in certain boot modes (notably
QSPI boot). Attempting to configure the PL with the loopback bit set
will result in timeouts and will prevent successful configuration.
In order to avoid this problem, and to avoid dependency on the version
of the FSBL used to boot the system, ensure that the loopback enable bit
is cleared when loading the driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
than 1sec, hence increased the program time by 4sec to
sync' all soc's.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add an option to skip cfb console init for boards
who want to show a logo, but not use the cfb console. This is
needed for the siemens boards, which have a bmp bootlogo, but
do not need the cfb console.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: use '__weak int board_cfb_skip(void)']
Signed-off-by: Anatolij Gustschin <agust@denx.de>
without this patch the bdinfo command shows:
U-Boot# bd
arch_number = 0x000010DC
[...]
sp start = 0x8EF32F20
FB base = 0x00000000
with this patch it shows the address where the framebuffer
for this video driver start:
arch_number = 0x000010DC
[...]
sp start = 0x8EF32F20
FB base = 0x8EF3C788
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
to use this driver also on am335x based boards, the following
changes are made:
- struct lcd_ctrl_config lcd_cfg is now configurable
through board code
- controller base is configurable through define
DA8XX_LCD_CNTL_BASE. To be compatible with older
da8xx based boards: If this define is missing, the
DAVINCI_LCD_CNTL_BASE is used
- Determine LCD IP Version, and make the driver
working on lcd revision register values:
Version 1:
0x4C100102
Version 2:
0x4F200800
0x4F201000
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
the da8xx-fb driver works also on am335x boards. So move
the da8xx-fb.h file from arch/arm/include/asm/arch-davinci
to drivers/video, so this driver can used from am335x
based boards. Also add WVGA panel_type.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
This is u-boot driver for L5F31188 panel.
I tested it in the board based on MIPI DSI with EXYNOS4 series, and it worked well.
Changes in V2:
- Replaced license header by SPDX-License-Identifier.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Donghwa Lee <dw09.lee@samsung.com>
[agust: sort Makefile entry alphabetically]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The cfb_console can't handle 4-bit wide font properly, since with
4-bit wide font, all 8 bits are drawn. Unbreak the video_drawchars()
function to correctly render 4-bits only on such fonts.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
The LCDIF interface doesn't give us any means to do continuous refresh
when driving a SmartLCD. To work this around, we produce a special
circular DMA descriptor, which only writes the HW_LCDIF_CTRL0 register
and sets the RUN bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add hook that allow configuring SmartLCD attached the MXS LCDIF
controller operating in System-Mode. This hook can be overriden
by a platform-specific SmartLCD programming routine, which writes
the SmartLCD specific values into it's registers.
Also, this patch makes sure the SYNC signals are off for the
SmartLCD case.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allocate the framebuffer aligned so it can be flushed
and the flush_dcache_range() function won't complain.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Add special function that executes a specially crafted circular
DMA descriptor. The function doesn't wait for the descriptor to
finish the transfer, since the descritor never finishes. This is
useful when operating a SmartLCD through the LCDIF interface, as
the LCDIF does not give us any means to have continuous refresh
of the SmartLCD. Instead, the RUN bit in the LCDIF CTRL register
must be triggered manually. This can be worked around by starting
an DMA transfer which continuously sets the RUN bit. This function
allows starting exactly such transfer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
T4240 PCIe IP is version 3.0 and has some update comparing previous
QorIQ products.
1. Move Freescale specific register define
to
arch/powerpc/include/asm/fsl_pci.h
and update the register offset define for T4240.
2. add the status/control register define
use status/control register to judge the link status
3. The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, T4240 does not support this functionality.
According to PCIE specification, 'Header Type' offset 0x0e is used to
indicate header type, so for PCIE controller, the patch changes code to
use 'Header Type' field to identify if the PCIE is RC or EP mode.
This patch fixes the PCIe card link up issue on T4240QDS.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
FMAN firmware can be in NOR flash, NAND flash, SPI flash, MMC or even
remote. In case none of them is defined, set it to null.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for SST25WF080 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- line over 80 characters
- foo * bar -> foo *bar
- removed unnecessary for single statement blocks.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
In case only the CONFIG_SYS_I2C_SPEED is set in configuration file,
the CONFIG_SYS_I2C_SOFT_SPEED is defined as CONFIG_SYS_I2C_SPEED.
The CONFIG_SYS_I2C_SOFT_SPEED is then used throughout the driver.
Unfortunatelly, due to a typo in the driver, instead of defining
CONFIG_SYS_I2C_SOFT_SPEED, an CONFIG_SYS_SOFT_I2C_SPEED was defined
and therefore the driver failed to compile. The same applies for
CONFIG_SYS_I2C_SOFT_SLAVE , where the swap happens as well.
This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Use DIV_ROUND_UP to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
In special_gpio_free(), call unreserve() rather than reserve() to release gpio.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
accessing a lan9303 switch with the cpsw driver results in wrong
speed detection, as the switch sets the BMSR_ERCAP in BMSR
register, and follow read of the MII_STAT1000 register fails, as
the switch does not support it. Current code did not check,
if a phy_read() fails ... fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.
Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Fixes NFS root problems with Beagle (3530 ES1.0) when used with
external USB-ethernet adapter and "USB start" command used within
u-boot.
Soft resetting the UHH module causes instability issues on
all OMAPs so we just avoid it.
See OMAP36xx Errata
i571: USB host EHCI may stall when entering smart-standby mode
i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
On OMAP4/5, soft-resetting the UHH module can put it into
Smart-Idle mode and lead to a deadlock.
On OMAP3 this doesn't seem to be the case but still instabilities
are observed on beagle (3530 ES1.0) if soft-reset is used.
e.g. NFS root failures with Linux kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Implement functions to flush/invalidate dcache over QH and qTDs
and make use of them where appropriate. Also use them to replace
the old incorrect cache management attempt. This is the first step
towards making this driver work with data cache enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The code for retrieving qTD item for particular endpoint is hard
to understand, moreover it's duplicated all over the driver. Move
the code into single nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The code for retrieving QH for particular endpoint is hard to understand,
moreover it's duplicated all over the driver. Move the code into single
nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Check the length of system cacheline at compile-time and fail
if the system uses too long cachelines.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoint QH list has to be aligned to 10-bit boundary. We also have
to make sure the list is aligned on a cacheline boundary. Make sure it
is. Furthermore, check if the memory allocation for the QH list didn't
fail. Moveover, improve the comment about the QH list structure.
Finally, the qTD item list has to be aligned only to 5-bit boundary, not
10-bit as it is now, fix this as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
There is no need to init this field at runtime, so init it statically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The QH_MAXNUM is used in absolutelly incorrect manner and is not
even needed. Remove it and correctly replace it's occurance with
2 * NUM_ENDPOINTS .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
