Commit graph

954 commits

Author SHA1 Message Date
Hans de Goede
019731a88f sunxi: Sync h3-orangepi dts files with kernel
This adds an emac node to the orangepi-2 dts (not yet merged upstream,
but in u-boot we already have emac support); fixes the alphetically
sorting of nodes in sun8i-h3-orangepi-plus.dts and disables some
usb controllers in sun8i-h3-orangepi-plus.dts which are only used
on the plus2e, as upstream has decided to do a separate dts files
for the plus2e.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 10:57:00 +02:00
Chen-Yu Tsai
68871efe1d sunxi: Fix H3 EMAC syscon register address
The sun8i-emac driver follows an old version of the proposed DT
bindings, where the EMAC clock and EPHY control register range is
listed directly, rather than through a syscon phandle.

Add back the syscon register range to avoid an invalid data access.
We should fix the driver once the Linux kernel bindings have been
finalized.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 10:33:54 +02:00
Stefan Mavrodiev
ca5c37026b sunxi: Add support for A33-OLinuXino board
A33-OLinuXino is A33 development board designed by Olimex LTD.

It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.

It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.

The dts files are identical to the ones submitted to the upstream kernel.

Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 10:33:44 +02:00
Icenowy Zheng
8e71a7ebdc sunxi: add proper device tree for iNet D978 rev2 boards
Add a proper dts for the iNet D978 rev2 based A33 tablets.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-09-03 10:04:15 +02:00
Peter Chubb
b615267633 ARM: tegra: Add support for TK1-SOM board from Colorado Engineering
The Colorado TK1 SOM is a small form factor board similar to the
Jetson TK1.  The main differences lie in the pinmux, and in that the
PCIe controller is set to use in 4lanes+1lane, rather than 2+2.

The pinmux header here was generated from a spreadsheet provided by
Colorado Engineering using the tegra-pinmux scripts.  The spreadsheet
was converted from v09 to v11 by me.

Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-01 09:24:30 -07:00
Stephen Warren
7932d3e4a7 ARM: tegra: use numeric versioning for p2771-0000
The board ID EEPROM and board ID stickers on p2771-0000 will use a numeric
versioning scheme, with version numbers such as 000/100/200/300/400/500.
Within NVIDIA, these versions are also known as A00/A01/A02/A03/A04/B00.
However, that numbering scheme is not easily visible outside of NVIDIA,
and so does not make much sense to use. Convert U-Boot to use the readily
visible numeric scheme.

Also, it turns out that the current A02 DT actually applies to board
versions 000/100/200 (A00..A02). Consequently rename this to 000 not 200
so that all U-Boot builds are named after the first version of the HW they
support.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-30 11:14:53 -07:00
Tom Rini
ff62bdfbd5 Merge branch 'master' of git://git.denx.de/u-boot-uniphier 2016-08-28 10:36:20 -04:00
Masahiro Yamada
f0633533d5 ARM: dts: uniphier: add u-boot, dm-pre-reloc to use eMMC boot on sLD3
The eMMC on sLD3 is assigned with dedicated pins (only multiplexed
with GPIO), so it shouldn't hurt to enable eMMC on SPL all the time.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-08-28 13:11:34 +09:00
Hans de Goede
8d463c5a32 sun5i: Add defconfig and dts file for the Empire Electronix M712 tablet
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-08-26 16:58:36 +02:00
Hans de Goede
860fbdd41f sunxi: Sync dts files with upstream kernel
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.

Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-08-26 16:58:36 +02:00
Hans de Goede
a1243f7851 sun6i: Add defconfig and dts file for tablets using the inet-q972 PCB
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.

Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.

This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.

The dts files are identical to the ones submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-08-26 16:58:36 +02:00
Stephen Warren
6002c75c59 ARM: tegra: remove stale nvidia, bpmp I2C DT property
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-25 13:48:11 -07:00
Stephen Warren
eb3f68afbc ARM: tegra: fix Tegra186 SDHCI clock/reset names
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-25 13:47:49 -07:00
Stephen Warren
b4ee081e5a ARM: tegra: fix Tegra186 I2C clock name
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-25 13:47:49 -07:00
Sekhar Nori
ce52531c5d ARM: dts: k2g-evm: enable mmc/sd suppport
The K2G EVM from TI has an SD card slot as
well as onboard eMMC for data storage.

Enable support for these.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-16 10:24:11 +09:00
Sekhar Nori
5396edc675 ARM: dts: K2G: Add support for MMC controller
K2G SoC from TI has two MMC/SD controllers.
Add device tree data for these.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-16 10:24:10 +09:00
Tom Rini
0fcb9f07a1 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-08-15 17:31:23 -04:00
Wenyou Yang
2c4b2dd289 ARM: at91/dt: Add device tree for SAMA5D2 Xplained
Add device tree for SAMA5D2 Xplained board.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2016-08-15 22:58:04 +02:00
Wenyou Yang
256a3f2466 atmel: Bring in at91 pio4 device tree file and bindings
Bring in required device tree file and bindings from Linux.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-15 22:58:04 +02:00
Stephen Warren
a6bb0084c2 ARM: tegra: enable PCIe controller on p2771-0000
p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
connector (which may run at x2 electrically, depending on the board
version and configuration) and a x1 connection to the M.2 slot (which may
not be active, depending on the board version and configuration). This
change enables those.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-15 10:26:13 -07:00
Stephen Warren
45d85f0872 ARM: tegra: enable SD card on p2771-0000
Now that clock and reset drivers exist for Tegra186, we can enable the SD
card controller. Now that a BPMP I2C driver exists for Tegra186, we can
communicate with the PMIC to enable power to the SD card. Hook up the DT
content and board code required to make the SD card work.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-15 10:26:13 -07:00
Bryan Wu
ad3c144fb8 ARM: tegra: enable I2C buses for P2771-0000
Enable I2C devices in DT and enable building tegra_i2c.c driver.

Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, commit msg rework, fixed DT node sort order)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-15 10:26:13 -07:00
Vignesh R
257bdb3f66 ARM: dts: dra7xx-evm: add evm_3v3_sd regulator
Add a node for evm_3v3_sd using onboard PCF GPIO expander which feeds
on to mmc vdd.
Update mapping for vmmc-supply and vmmc_aux-supply.
evm_3v3_sd supplies to SD card vdd, and ldo1 to sdcard i/o lines.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-12 09:22:18 -04:00
Tom Rini
2f1eb66e28 Merge branch 'master' of git://git.denx.de/u-boot-usb 2016-08-11 07:22:55 -04:00
Vignesh R
ceec08f50b ARM: dts: dra72-evm: Add mode-gpios entry for mac node
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-08-08 13:32:55 -04:00
Vignesh R
06974ea0e3 ARM: dts: dra7xx: Add u-boot specific property for PCF8575 nodes
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-08-08 13:32:54 -04:00
Rajesh Bhagat
a866c2145a dm: ls1021a: dts: Update USB 3.0 node to support DM USB
Update USB 3.0 controller dts node in ls1021a.dtsi.

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-08-07 21:55:43 +02:00
Tom Rini
2863a9bfc2 Merge git://git.denx.de/u-boot-rockchip 2016-08-06 11:38:14 -04:00
Kever Yang
da8ff82e73 dts: rk3399: enable dwmmc for sdcard
rk3399 sdcard is using dwmmc controller, enable it for sdcard.
SCLK_SDMMC is the clock for controller operation clock, move it
to the first place.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-08-05 18:02:52 -06:00
Xu Ziyuan
1c62d99952 rockchip: add support for rk3288 miniarm board
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-08-05 17:56:08 -06:00
Sandy Patterson
2918d96728 rockchip: rockchip, sdram-channel 0xff fix remaining dts
Add an extra byte so that this data is not byteswapped.

Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-08-05 17:56:07 -06:00
Xu Ziyuan
d2d763fa83 rockchip: add fastboot support for rk3036 board
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-05 17:56:07 -06:00
Bryan Wu
9e613de0e1 ARM: tegra: add I2C controllers to Tegra186 DT
Tegra186 has 8 I2C controllers including BPMP I2C. This patch adds the
other 7 generic controllers to Tegra186's DT.

Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, fixed DT node sort order, tweak patch description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:59 -07:00
Stephen Warren
20bbde0628 ARM: tegra: add PCIe controller to Tegra186 SoC DT
The Tegra186 PCIe DT content is almost identical to previous chips, except
that the:

- There are 3 ports instead of 2.
- Some physical addresses have moved.
- PHY programming is handled by firmware, so CCPLEX DTs don't need to
  reference any PHY.
- The power domain is explicitly represented in DT. This change is
  mandatory for Tegra186 since standard power domain APIs are used, and
  should be made to the DT for older SoCs, although we get away without
  doing so since U-Boot currently uses custom APIs that hard-code power
  domain IDs.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:59 -07:00
Stephen Warren
23ab5bda7e ARM: tegra: add BPMP I2C to Tegra186 device tree
This allows the BPMP I2C device to be instantiated, which makes it
available to other drivers and the user.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:59 -07:00
Stephen Warren
19014203c4 ARM: tegra: add BPMP and dependencies to Tegra186 DT
This adds the DT content that's needed to allow board DTs to enable use
of BPMP, clocks, resets, GPIOs, eMMC, and SD cards.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:59 -07:00
Stephen Warren
729c2db7a9 ARM: tegra: adapt to latest HSP DT binding
The DT binding for the Tegra186 HSP module apparently wasn't quite final
when I posted initial U-Boot support for it. Add the final DT binding doc
and adapt all code and DT files to match it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-08-04 13:36:58 -07:00
Michal Simek
a9022b017a ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes
Serial driver is getting clk information via DT that's why
also clk node needs to have this flag.

Different behavior was introduced by:
"dm: Use dm_scan_fdt_dev() directly where possible"
(sha1: 911954859d)
where simple-bus driver starts to call dm_scan_fdt_dev() which has
additional logic around pre_reloc_only parameter which exclude
clk nodes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-08-01 08:35:02 +02:00
Tom Rini
26fb8db0f4 Merge git://git.denx.de/u-boot-rockchip 2016-07-31 20:31:13 -04:00
Hans de Goede
fcada3b05e sunxi: Re-enable h3 emac support
With the recent bug fixes for the sun8i_emac driver all known issues
are resolved, so we can re-enable the driver.

While at it, also enable the emac on the Orange Pi One.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Jagan Teki <jteki@openedev.com>
2016-07-31 21:45:47 +02:00
jk.kernel@gmail.com
dd63fbc70a rockchip: add support for rk3288 PopMetal board
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
d7ca67b7cd rockchip: add basic support for fennec-rk3288 board
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
8a632ac135 rockchip: add a dummy byte for the sdram-channel property
Add an extra byte so that this data is not byteswapped.

Signed-off-by: Ziyuan Xu <jk.kernel@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
2016-07-31 07:24:20 -06:00
Vignesh R
9af6ce4248 ARM: dts: am57xx-idk-common: Enable support for QSPI
AM571x and AM572x IDK have a spansion s25fl256s QSPI flash on the board
connected to TI QSPI over CS0. Hence, add QSPI and flash slave
DT nodes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Vignesh R
70ebdd775b ARM: dts: dra7xx: Update spi-max-frequency for QSPI
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Tom Rini
0b6699ad8e Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-07-26 18:33:04 -04:00
Chen-Yu Tsai
6d7b22a5d8 sunxi: Add EMAC ethernet0 alias for H3 dtsi
The sunxi ethernet address generation code looks for ethernet[0-3]
aliases to find ethernet controllers to generate MAC addresses for.

Without a valid address, the driver fails to register.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:02 +02:00
Hans de Goede
2a5adc5b3c sunxi: Add defconfig and dts file for the Orange Pi PC Plus SBC
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.

The upstream kernel devs have decided that they want a separate
dts for the PC Plus rather then sharing a single dts between the
regular PC and the PC Plus. So add a new orangepi_pc_plus_defconfig
to match.

The added dts file matches the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-26 21:56:02 +02:00
Kever Yang
777c834fd4 dts: add support for Rockchip rk3399 soc
These files are from kernel upstream:
"649a371 Add linux-next specific files for 20160616"
with some modification need by U-Boot:
- chosen with stdout-path to uart2.
- add clock-frequency for uart2

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:46:45 -06:00
Xu Ziyuan
266c8fad51 rockchip: rk3288: add fastboot support
Enable fastboot feature on rk3288.

This path doesn't support the fastboot flash function command entirely.
We will hit "cannot find partition" assertion without specified
partition environment. Define gpt partition layout in specified board
such as firefly-rk3288, then enjoy it!

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:19 -06:00
Xu Ziyuan
744368d6ae rockchip: add basic support for evb-rk3288 board
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).

evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-07-25 20:44:18 -06:00
Boris Brezillon
c1aa7d629e sunxi: Enable NAND controller on the CHIP
Enable the NAND controller in the sun5i-r8-chip.dts.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-07-24 20:36:29 -05:00
Maxime Ripard
32b18435de sun5i: Add NAND controller to the sun5i DTSI
Add the NAND controller definition to sun5i.dtsi.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-07-24 20:36:28 -05:00
Masahiro Yamada
fe8dc1fac7 ARM: dts: uniphier: renumber serial aliases for Gentil/Vodka boards
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console.  The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.

[ Linux commit: 2a4a2aadbaad9dffdb564a2895348f3d8e825416 ]

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
2016-07-23 23:24:46 +09:00
Stephen Warren
1f60f0731d ARM: tegra: split p2771-0000 build
There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.

With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21 09:31:30 -07:00
Stephen Warren
0388634a6c ARM: tegra: fix Tegra186 DT GPIO binding header
Tegra186 uses different GPIO port IDs compared to previous chips. Make
sure the SoC DT file includes the correct GPIO binding header.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-21 09:31:30 -07:00
Tom Rini
1f9ef0dca0 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-07-15 10:44:01 -04:00
Hans de Goede
66ab528673 sunxi: Add defconfig and dts file for the Orange Pi Lite SBC
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-15 15:54:56 +02:00
Hans de Goede
fa8a485d06 sunxi: Sync sun8i-h3-orangepi-plus.dts with upstream
This enables extra USB controllers which enable use of the 3rd USB
port on the new Orange Pi Plus 2E variant.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-15 15:54:56 +02:00
Tom Rini
926fbcc083 Merge branch 'master' of git://git.denx.de/u-boot-samsung 2016-07-15 08:06:42 -04:00
Amit Singh Tomar
a29710c525 net: Add EMAC driver for H3/A83T/A64 SoCs.
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).

BIG Thanks to Andre for providing some of the DT code.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 08:34:34 +02:00
Simon Glass
9ca7e6720e rockchip: Update the sdram-channel property to support of-platdata
Add an extra byte so that this data is not byteswapped. Add a comment to
the code to explain the purpose.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-14 20:40:24 -06:00
Jaehoon Chung
836efb33e3 ARM: exynos4: dts: add the prefix '/' for aliases nodes
It's correct to use '/' as prefix for aliases nodes.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-07-12 14:27:55 +09:00
Tom Rini
bff97dde8c Merge branch 'master' of git://git.denx.de/u-boot-spi 2016-07-11 18:50:29 -04:00
Vignesh R
e835a74159 ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
b60774fff1 ARM: dts: K2G: Add support for QSPI controller
K2G SoC has a Cadence QSPI controller to communicate with NOR flash
devices. Add DT nodes to support the same.
Also, K2G EVM has a s25fl512s flash connect to QSPI bus at CS 0. Add nor
flash slave node for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:33 +05:30
Vignesh R
c8e750473a ARM: dts: k2g: add support for Davinci SPI controller
K2G SoC has 4 SPI instances that are compatible with davinci_spi
controller(present on previous generation of Keystone2 devices). Add DT
nodes for the same. K2G EVM has a N25Q128A13 SPI NOR flash connected on
SPI-1. Add DT bindings for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
188179481d ARM: dts: k2l: Enable Davinci SPI controller
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:32 +05:30
Vignesh R
2655f1625a ARM: dts: k2e: Enable Davinci SPI controller
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
96368e6e38 ARM: dts: k2hk: Enable Davinci SPI controller
Now that davinci_spi driver has been converted to DM framework, enable
the same in DT. Also add "spi-flash" as compatible property to
n25q128a11 node as it is required for flash device to be probed in
U-Boot.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Vignesh R
e5fcf0372b ARM: dts: keystone2: add SPI aliases for davinci SPI nodes
Add aliases for SPI nodes in order for it to be probed by the DM
framework.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-09 20:16:31 +05:30
Simon Glass
ec5507707a video: tegra: Move to using simple-panel and pwm-backlight
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.

This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:

   - colibri
   - medcom-wide
   - paz00
   - tec

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Simon Glass
ce02a71c23 tegra: dts: Sync tegra20 device tree files with Linux
Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05 13:19:08 -07:00
Quentin Schulz
d2a6af0528 sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.

The DTS file is identical to the one submitted to the upstream kernel.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-02 13:53:15 +02:00
Masahiro Yamada
1013aef330 ARM: dts: uniphier: add AIDET nodes
The AIDET (ARM Interrupt Detector Add-on Circuit) is a kind of
syscon block related with the interrupt controller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:30 +09:00
Masahiro Yamada
c4adc50ea6 ARM: dts: uniphier: sync Device Trees with upstream Linux
I periodically sync Device Trees for better maintainability.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02 05:44:29 +09:00
Tom Rini
44faff24f5 Merge git://git.denx.de/u-boot-fsl-qoriq 2016-06-28 15:59:05 -04:00
Abhimanyu Saini
dee01e426b armv8: dts: fsl: Remove cpu nodes from Layerscape DTSIs
Currently layescape SoCs are not using cpu nodes. So removing
them in favour of compatibly with  similar SoCs that
have different cores like LS2080A and LS2088A.

This has been tested on LS2080AQDS, LS1043ARDB, LS1012ARDB.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28 12:08:54 -07:00
Heiko Schocher
8e6e8221c7 arm: at91: taurus/axm: add DM and DTS support
add DM and DTS support for the at91 based siemens
boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Heiko Schocher
13ee789074 arm: at91: smartweb: add DM and DTS support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Heiko Schocher
ae21e964d8 arm: at91: dts: Bring in dts files for AT91SAM9G20 and SAM9260
Add this files from Linux v4.6-rc5

66b8a424d: [workqueue: fix ghost PENDING flag while doing MQ IO]

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Heiko Schocher
289f979cc9 corvus DTS / DM support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebase on current ToT, don't delete gurnard DTB creation]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-26 20:17:22 +02:00
Hans de Goede
3551b24f53 sunxi: Add defconfig and dts file for inet86dz board
The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

The dts file this commit adds is identical to the one submitted to
the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20 22:43:59 +02:00
Hans de Goede
cd38e3d1b4 sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tablet
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-06-20 22:43:59 +02:00
Stephen Warren
0f67e2395b mailbox: add Tegra186 HSP driver
Tegra186's HSP module implements doorbells, mailboxes, semaphores, and
shared interrupts. This patch provides a driver for HSP, and hooks it
into the mailbox API. Currently, only doorbells are supported.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
2016-06-19 17:05:55 -06:00
Tom Rini
6beacfcff8 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2016-06-18 23:46:43 -04:00
Heiko Schocher
71423435fb arm, am335x: siemens: enable DM/DTS support
enable basic DM/DTS support for the siemens am335x based boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-06-17 09:51:05 -04:00
Schuyler Patton
332dddc6a1 ARM: dts: AM572x-IDK Initial Support
Add initial DTS support for AM572-IDK evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:38 -04:00
Lokesh Vutla
165bd7a1cc board: am57xx: Rename TARGET_BEAGLE_X15 as TARGET_AM57XX_EVM
board/am57xx supports all boards based on am57xx. Rename the taget
as TARGET_AM57XX_EVM.

Fixes: 74cc8b097d ("board: ti: beagle_x15: Rename to indicate support for TI am57xx evms")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-06-13 08:56:36 -04:00
Tom Rini
fd9102dafe Merge branch 'master' of git://git.denx.de/u-boot-atmel 2016-06-13 08:50:58 -04:00
Andre Renaud
885fc03aab arm: at91: Add support for gurnard
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.

Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Simon Glass
6f9678567a arm: at91: dts: Bring in device tree file for AT91SAM9G45
Add this file from Linux v4.5.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2016-06-12 23:49:38 +02:00
Yuan Yao
95ab851de0 dts: ls2080aqds: Add QSPI dts node
Add QSPI controller and slave dts node for LS2080AQDS board.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10 13:45:00 -07:00
Pavel Machek
35546f6f20 ARM: socfpga: add support for IS1 board
This adds support for IS1 board. Pretty usual socfpga board,
256MB of RAM, does not have MMC, two SPI chips, one ethernet port, two
additional ethernet ports connected to the FPGA.

Signed-off-by: Pavel Machek <pavel@denx.de>
2016-06-08 02:56:30 +02:00
Tom Rini
d77fa2ff76 Merge http://git.denx.de/u-boot-samsung
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/peach-pi_defconfig
	configs/peach-pit_defconfig
2016-06-06 13:39:43 -04:00
Tom Rini
1cb9cb3ec0 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-06-06 07:16:39 -04:00
Michal Simek
08ac386bb2 ARM64: zynqmp: Add support for zc1751-dc4
zc1751-dc4 contains four GEMs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-06-06 11:23:27 +02:00
Tom Rini
c41c649c2f Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-06-04 08:49:08 -04:00
Prabhakar Kushwaha
ff78aa2ba1 armv8: ls1012a: Add support of ls1012afrdm board
QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance
development platform, with a complete debugging environment.
The LS1012AFRDM board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:51 -07:00
Prabhakar Kushwaha
3b6e3898c2 armv8: ls1012a: Add support of ls1012ardb board
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:51 -07:00
Prabhakar Kushwaha
9d044fcb8c armv8: ls1012a: Add support of ls1012aqds board
QorIQ LS1012A Development System (LS1012AQDS) is a high-performance
development platform, with a complete debugging environment.
The LS1012AQDS board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 14:12:51 -07:00
Tom Rini
f15715afea Merge branch 'master' of git://git.denx.de/u-boot-tegra 2016-06-03 16:30:47 -04:00
Marek Vasut
569a191a86 arm: socfpga: Add samtec VIN|ING board
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
 - 1 GiB of DRAM
 - 1 Gigabit ethernet
 - 1 USB gadget port
 - 1 USB host port with an on-board hub
 - 2 QSPI NORs connected to the Cadence QSPI core
 - Multiple I2C EEPROMs and one I2C temperature sensor

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
---
V2: Update the defconfig as per Tom's request
2016-06-01 22:44:14 +02:00
Stephen Warren
10a03382f0 ARM: tegra: add p2771-0000 board support
P2771-0000 is a P3310 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB micro-B
port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO expansion
headers.

Currently, due to U-Boot's level of support for Tegra186, the only
features supported by U-Boot are the console UART and the on-board eMMC.
Additional features will be added over time.

U-Boot has so far been tested by replacing the kernel image on the device
with a U-Boot binary. It is anticipated that U-Boot will eventually
replace the CCPLEX bootloader binary, as on previous chips. This hasn't
yet been tested.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-31 11:22:59 -07:00
Stephen Warren
c7ba99c8c1 ARM: tegra: add core Tegra186 support
This adds the bare minimum code to support Tegra186, with UART and eMMC
working.

The empty gpio.h is required because <asm/gpio.h> includes it. A future
cleanup round may be able to solve this for all Tegra generations at once.

mach-tegra/Makefile is adjusted not to compile anything for Tegra186, but
instead to defer everything to mach-tegra/tegra186/Makefile. This allows
the SoC code to pick-and-choose which of the C files in the "common"
mach-tegra/ directory to compile in based on the SoC's needs. Most of the
code is not valid for Tegra186, and this approach removes the need for
mach-tegra/Makefile to contain many SoC-specific ifdefs. This approach
may be applied to all other Tegra SoCs in a future cleanup round.

board186.c is introduced to replace board.c and board2.c. These files
currently contain a slew of SoC- and board-specific code that is not
valid for Tegra186. This approach avoids adding yet more ifdefs to those
files. A future cleanup round may refactor most of board*.c into board-/
SoC-specific functions files thus allowing the top-level functions like
board_init_early_f to be shared again.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-05-31 11:22:59 -07:00
Tom Rini
378f9134eb Merge git://git.denx.de/u-boot-rockchip 2016-05-27 15:48:53 -04:00
Lokesh Vutla
73ec696059 ARM: dts: AM335x-ICEv2: Add minimal dts support
Add minimal dts support for AM335x-ICEv2 board

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-05-27 15:47:53 -04:00
Lokesh Vutla
da9d9599ac ARM: dts: AM335x-BBG: Add initial support
Add initial DTS support for AM335x-BBG

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
3819ea7063 ARM: dts: AM335x-evmsk: Add initial support
Add initial DTS support for AM335x-evm sk.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Mugunthan V N
2c6485bc7c ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
a1b4885153 ARM: dts: am335x-bone: Enable uart and timer
Allow am335x-bone.dts to be built and enable uart and timer
for all beaglebones.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:48 -04:00
Lokesh Vutla
54a92e1ad8 ARM: dts: AM437x-IDK Initial Support
Add initial DTS support for AM437x-IDK evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:46 -04:00
Lokesh Vutla
7dd1283048 ARM: dts: AM43x-EPOS Initial Support
Add initial DTS support for AM43-EPOS evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:46 -04:00
Beniamino Galvani
bfcef28ae4 arm: add initial support for Amlogic Meson and ODROID-C2
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].

[1] https://patchwork.ozlabs.org/patch/603583/

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-27 15:39:47 -04:00
Sjoerd Simons
2ed6dc8338 rockchip: rock2: dts: use status = "okay" not ok
u-boot only recognize okay to enable a node (Linux seems to be more
lenient here). So use okay instead.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-27 09:00:48 -06:00
Sjoerd Simons
1c09a7fb98 rockchip: rk3288-firefly: Add gmac definition
Add a definition for the gmac interface to the firefly device-tree.
Copied verbatim from the linux kernel.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
2016-05-27 09:00:48 -06:00
Tom Rini
82f2a14491 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-05-25 12:32:56 -04:00
Andre Przywara
c1fd244187 arm64: Pine64: update FDT files
The originally committed .dts files for the Pine64 were from an early
proof-of-concept version and should have never been committed upstream.
Replace them with much more mature versions, which also use a different
naming scheme.
Please note that at this point there is at least one binding which has
not been agreed upon, so this is subject to change.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-25 17:52:39 +02:00
Masahiro Yamada
d7e103c08f ARM: uniphier: add EHCI nodes for PH1-LD11
Make the USB feature really available.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-05-26 00:37:13 +09:00
Simon Glass
f948f5de94 exynos: dts: Add display-related device tree fragments
Bring in device tree pieces related to display from Linux 4.4 for:

- snow
- peach_pit
- peach_pi
- spring

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 13:25:18 +09:00
Simon Glass
141c74350d exynos: dts: Add pwm device tree node
Add this node from Linux v4.4 so that PWMs can be used in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 13:25:18 +09:00
Thomas Abraham
6c15a2a996 board: samsung: add initial Espresso7420 board support
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 10:00:19 +09:00
Thomas Abraham
e39448e8be arm: exynos: add support for Exynos7420 SoC
Add support for Exynos7420 SoC. The Exynos7420 SoC has four Cortex-A57
and four Cortex-A53 CPUs and includes various peripheral controllers.

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-05-25 10:00:19 +09:00
Tom Rini
fc15b9beed Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-05-24 13:42:03 -04:00
Tom Rini
2ee490a024 Merge branch 'master' of git://git.denx.de/u-boot-net
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	drivers/net/zynq_gem.c
2016-05-24 11:59:02 -04:00
Mugunthan V N
844f814478 arm: dts: dra7: fix ethernet name with proper device address
Fix typo error for cpsw device name with proper device address

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:03 -05:00
Mugunthan V N
d7dc888d60 arm: dts: dra7: add syscon node to cpsw to read mac address
Add syscon node to cpsw device node to read mac address
from efuse.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:03 -05:00
Mugunthan V N
dcda79e119 arm: dts: am4372: add syscon node to cpsw to read mac address
Add syscon node to cpsw device node to read mac address
from efuse.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-05-24 11:42:03 -05:00
Michal Simek
c9811e14cf ARM64: zynqmp: Add missing u-boot,dm-pre-reloc to DTSI
Add missing u-boot,dm-pre-reloc to get IPs initialized.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 11:15:01 +02:00
Alexander Graf
0a8c4f67f3 ARM64: zynqmp: Align gic ranges for 64k in device tree
The GIC ranges in the zynqmp device tree are only 4kb aligned. Since
commit 12e14066f we automatically deal with aliases GIC regions though,
so we can map them transparently into guests even on 64kb page size
systems.

This patch makes use of that features and sets GICC and GICV to 64kb
aligned and sized regions.

Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 11:15:01 +02:00
Masahiro Yamada
621a93e140 ARM: dts: zynq: describe SLCR as simple-mfd rather than simple-bus
Commit 9f56917ab8 ("dm: core: make simple-bus compatible to
simple-mfd") made possible to import the following commit:

Linux commit: bc5ba9b98435bf76d92e0954da1784695aa449f1

The SLCR (System-Level Control Registers) block is an MFD (Multi
Function Device) rather than a bus.

"simple-mfd" seems a more suitable compatible string than "simple-bus".

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-05-24 11:15:00 +02:00
Yuan Yao
87e566d773 armv8/ls1043a: update the node for QSPI support
The address value and size value set for QSPI dts node "reg"
property have type of u64 on arm64.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:43 -07:00
Peng Fan
102412c415 dm: spi: soft_spi: switch to use linux compatible string
1. Support compatible string "spi-gpio" which is used by Linux
   Linux use different bindings, so use UBOOT_COMPAT and
   LINUX_COMPAT to differentiate them.
2. Introduce SPI_MASTER_NO_RX and SPI_MASTER_NO_TX to handle
   no rx or no tx case.
3. Tested on i.MX6 UltraLite board with 74LV595 spi-gpio chip.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Stephen Warren
54693cbdca video: tegra: refuse to bind to disabled dcs
This prevents the following boot-time message on any board where only the
first DC is in use, yet the DC's DT node is enabled:

stdio_add_devices: Video device failed (ret=-22)

(This happens on at least Harmony, Ventana, and likely any other Tegra20
board with display enabled other than Seaboard).

The Tegra DC's DT node represents a display controller. It may itself
drive an integrated RGB display output, or be used by some other display
controller such as HDMI. For this reason the DC node itself is not
enabled/disabled in DT; the DC itself is considered a shared resource, not
the final (board-specific) display output. The node should instantiate a
display output driver only if the rgb subnode is enabled. Other output
drivers are free to use the DC if they are enabled and their DT node
references the DC's DT node. Adapt the Tegra display drivers' bind()
routine to only bind to the DC's DT node if the RGB subnode is enabled.

Now that the display driver does the right thing, remove the workaround
for this issue from Seaboard's DT file.

Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Marek Vasut
268da813c7 ARM: socfpga: Disable USB OC protection on SoCrates
This is mandatory, otherwise the USB does not work.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2016-05-06 18:41:49 +02:00
Peter Griffin
7e4902d479 ARM: hisilicon: hikey: dts: Add pl011 additional clock binding.
This is a binding which only exists in U-Boot, but is
required to get working serial in U-Boot.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:10:34 -04:00
Peter Griffin
cd593ed699 ARM: hisilicon: hikey: Enable OF_CONTROL for hikey board.
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:10:34 -04:00
Peter Griffin
9122109ad7 ARM: hisilicon: hikey: Add hikey & hi6220 dts from v4.6-rc3.
Import the upstream kernel dts into U-Boot. Currently
only serial is supported, but a lot more DT changes are
queued for v4.7.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-25 15:10:31 -04:00
Masahiro Yamada
3d970876db ARM: dts: uniphier: add SD controller node for PH1-LD20
PH1-LD20 does not support 1.8V signaling for SD card; only Default
Speed and High Speed (up to 50MHz) with 3.3V signaling is supported.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:54:10 +09:00
Masahiro Yamada
6c64d50e47 ARM: dts: uniphier: move aliases node up to satisfy fdtgrep
Currently, fdtgrep would not accept uniphier-ph1-ld20-ref.dtb
and uniphier-ph1-ld11-ref.dtb unless the aliases node comes
the first in the root node.

$ make -s uniphier_pxs2_ld6b_defconfig
$ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-ld20-ref
  [snip]
  LDS     spl/u-boot-spl.lds
  LD      spl/u-boot-spl
  OBJCOPY spl/u-boot-spl-nodtb.bin
  FDTGREP spl/u-boot-spl.dtb
Error at 'fdt_find_regions': FDT_ERR_BADLAYOUT
/aliases node must come before all other nodes
Error: FDT_ERR_BADMAGIC
make[1]: *** [spl/u-boot-spl.dtb] Error 1
make: *** [spl/u-boot-spl] Error 2

This commit moves the aliases node as the error message from the
fdtgrep tool suggests, although this requirement does not sound
reasonable to me.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:53:56 +09:00
Masahiro Yamada
1222addb3f ARM: dts: uniphier: use Ref Daughter board on PH1-LD20 Ref board
This makes the EEPROM device on the Reference Daughter board
available.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-24 09:53:56 +09:00
Tom Rini
ec3ab3f9b5 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2016-04-20 09:23:42 -04:00
Stefan Roese
43809cfa1b arm: socfpga: socrates: Add eth0 alias to enable ethernet
This enables full ethernet usage, including U-Boot to write the board
specific MAC address (ethaddr) into the DT blob before passing it to
Linux.

Without this, the ethaddr is not detected in U-Boot at all, resulting
in this error upon bootup:

...
Model: EBV SOCrates
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:45 +02:00
Stefan Roese
84f841c5b9 arm: socfpga: Fix typos in DT files (environmnet -> environment)
Fix a small typo in some of the SoCFPGA dts files that has spread via
copy-and-paste.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
2016-04-20 11:28:45 +02:00
Mugunthan V N
e361421430 ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In DRA72x and AM57xx EVMs the card detect gpio is designed as
active low gpio. So correcting the dt card detect gpio
definition.

Also adding card-detect gpio for DRA74x EVM.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 12:29:19 -04:00
Mugunthan V N
103afa2abf ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs
As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In AM43xx the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-18 12:29:18 -04:00
Tom Rini
541c9be880 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-04-13 12:53:11 -04:00
Michal Simek
6c0c958de8 ARM64: zynqmp: Add support for zc1751 with DC cards
Support ZynqMP zc1751 with DC cards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:06 +02:00
Michal Simek
1f4f3d33c7 ARM64: zynqmp: Add support for ZCU102 platform
Add new board support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Punnaiah Choudary Kalluri
4521202760 ARM64: zynqmp: Add missing nand node for ep108
Add missing nand node for ep108.

Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Anurag Kumar Vulisha
ac8f6913c4 ARM64: zynqmp: Added OOB timing settings in zynqmp-ep108.dts
This patch adds the sata port phy OOB timing values in the sata
device-tree node.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Michal Simek
85d1142eb6 ARM64: zynqmp: Use 64bit size cell format for memory node
Enable option to support more then 4GB memories in single size block.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Michal Simek
a84de48e75 ARM64: zynqmp: Fix DWC3 binding with the kernel
Use the same binding as is used in mainline Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:05 +02:00
Michal Simek
786db82bd5 ARM64: zynqmp: Add serdes address space dp driver
For run time serdes adjustment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Michal Simek
c588d15444 ARM64: zynqmp: Align register description
Separate register space and put it on more lines.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Hyun Kwon
939cfeafec ARM64: zynqmp: dp: Add default properties to zynqmp.dtsi
Add some default properties to zynqmp.dtsi.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Hyun Kwon
695d75a122 ARM64: zynqmp: Use correct addresses in node names
Reflect actual silicon addresses in DT node names.

Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Michal Simek
4e31d27b9c ARM64: zynqmp: Align node address with parent node for dpdma
Use right addresses for channel names

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Michal Simek
ca2f5878d6 ARM64: zynqmp: Add backward compatible string for uart
Mainline kernel has no r1p12 compatible string that's why console stops
to work with the latest DTS files. Append generic compatible string.
Keep in your mind that using this generic compatible string not all uart
features will be available.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Michal Simek
91a8b0ee69 ARM64: zynqmp: Fix coding style for pcie
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Bharat Kumar Gogada
33aec51742 ARM64: zynqmp: Extend pcie node to support legacy interrupts
Modifying device tree node to support legacy interrupts.

Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Michal Simek
7c38ca36cb ARM64: zynqmp: Add interrupt-controller property to gpio nodes
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.

Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
Naga Sureshkumar Relli
908690098c ARM64: zynqmp: Add ddrc node in dts
This patch adds ddrc memory controller node in dts.
size mentioned in dts is 0x30000, because we need to access DDR_QOS
INTR registers located at fd090208 from this driver.

Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:04 +02:00
VNSL Durga
b34d11de18 ARM64: zynqmp: Added clocks to DT
ZynqMP DMA's main clock and apb clock are added
in zynqmp DT.

Signed-off-by: VNSL Durga <vnsldurg@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
2016-04-13 18:29:04 +02:00
Michal Simek
ff50d21bd2 ARM64: zynqmp: Add CCI-400 node
Add CCI-400 node to DTSI.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Michal Simek
14cd9eabb8 ARM64: zynqmp: Add missing interrupt-parent to PMU node
ZynqMP is not using global interrupt-parent setting that's why
it has to be listed in every node separately. PMU node missed it and
this patch is adding it.

Reported-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Soren Brinkmann
8f4e3972a0 ARM64: zynqmp: DT: Add power domains
Add power-domains to the DT and attach devices to them.
The power-domains are all logical domains as understood by firmware.
Each PD is identified by a unique identifier that the platform firmware
understands.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
P L Sai Krishna
bd750e7a6c ARM64: zynqmp: Added broken-tuning property to SD, eMMC nodes
This patch adds broken-tuning property to SD and
eMMC nodes.

Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Michal Simek
da2ad7843c ARM64: zynqmp: Sync GEM nodes with Linux
Remove jumbo properties which are handled in the driver directly
and use mainline compatible string which is already handled by the
driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Edgar E. Iglesias
7f1d7d974b ARM64: zynqmp: Hook up the GEMs to the SMMU
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Edgar E. Iglesias
88a85aac9f ARM64: zynqmp: Correct IRQ nr for the SMMU
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
P L Sai Krishna
b8bf553992 ARM64: zynqmp: Add 8-bit bus width property.
This patch add 8-bit bus width property to eMMC node.

Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Ranjit Waghmode
eaae2b5d0c ARM64: zynqmp: dt: Change qspi node compatible string
This patch makes compatible string as "m25p80" for qspi node in
ep108 device tree file

Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Michal Simek
beaf7955b7 ARM64: zynqmp: Add missing mmc aliases
Add missing mmc aliases.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Alistair Francis
02e782c6cd ARM64: zynqmp: Use C pre-processor for includes in dts
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all ZynqMP device trees inline
with each other.

Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:03 +02:00
Michal Simek
a195ed3359 ARM: zynq: Fix usb phy node for Zybo
Compatible property should be the first.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:02 +02:00
Michal Simek
371fc580d2 ARM: zynq: Extend microzed board support
Add missing DT nodes and enable USB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
2016-04-13 18:29:02 +02:00
Michal Simek
74720dc395 ARM: zynq: Add missing qspi for xm013
Add missing qspi node and make qspi as spi0.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:02 +02:00
Michal Simek
b347c14426 ARM: zynq: Create empty line below headers
Sync with others zynq DTS files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:02 +02:00
Michal Simek
a95d54b490 ARM: zynq: Align spi and qspi node locations
Keep nodes alphabelitally sorted.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
2016-04-13 18:29:02 +02:00
Christian Kohn
ac2c407490 ARM: zynq: zc706: Add adv7511 on i2c bus
Add missing adv7511 and configure to match Base TRD.

Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:02 +02:00
Christian Kohn
169050e4f5 ARM: zynq: zc702: Add adv7511 on i2c bus
Add bindings for adv7511.

Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Punnaiah Choudary Kalluri
c9132b1e44 ARM: zynq: DT: Add ethernet phy reset information
Added phy reset gpio information for gem0.

Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Michal Simek
936bbc5d16 ARM: zynq: Fix bootargs in board dtsi
- Sync with Linux kernel
- Remove rootfs
- Remove earlyprintk

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Michal Simek
77bb73decb ARM: zynq: Align devcfg node
- Have compatible string as the first property
- Sync with Linux kernel dtsi
- Add missing interrupt properties

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Moritz Fischer
20fe3f1791 ARM: dts: Updated devicetree bindings for Zynq 7000 platform
Added addtional bindings required for FPGA Manager operation
of the Xilinx Zynq Devc configuration interface.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Moritz Fischer
4c987271b3 ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Michal Simek
58fab4cd9c ARM: zynq: Add interrupt-controller property to gpio nodes
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.

Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-13 18:29:01 +02:00
Hans de Goede
ec770dba89 sunxi: Add defconfig and dts file for Orange Pi One SBC
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.

The dts is identical to the dts submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-04-12 08:58:03 +02:00
Hans de Goede
b24f7f008d sunxi: Enable usb ports on the Sinovoip BPI M3
DLDO3 is used to provide Port-D power and PD is used for the
usb-hub / sata-5v enable pins. The 2.5V comes from the schematic
and matches the factory image fex file.

The dts changes are the minimal changes needed for u-boot to
pick-up the usb host controllers. The upstream kernel does not
(yet) have usb host support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-04-12 08:58:03 +02:00
Stefan Roese
606576d54b arm: mvebu: Add basic support for Armada 375 eval board db-88f6720
This patch adds basic support for the Marvell A375 eval board. Tested
are the following interfaces:
- I2C
- SPI
- SPI NOR
- Ethernet (mvpp2), port 0 & 1

Currently the A375 SerDes and DDR3 init code is not intergrated. So
the SPL U-Boot is not fully functional.

Right now, this A375 mainline U-Boot can only be used by chainloading
it via the original Marvell U-Boot. This can be done via this
command:

=> tftpboot 00800000 a375/u-boot-dtb.bin;go 00800000

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-04-04 11:22:10 +02:00
Mateusz Kulikowski
626f048bbc board: Add Qualcomm Dragonboard 410C support
This commit add support for 96Boards Dragonboard410C.
It is board based on APQ8016 Qualcomm SoC, complying with
96boards specification.
Features (present out of the box):
- 4x Cortex A53 (ARMv8)
- 2x USB Host port
- 1x USB Device port
- 4x LEDs
- 1x HDMI connector
- 1x uSD connector
- 3x buttons (Power, Vol+, Vol-/Reset)
- WIFI, Bluetooth with integrated antenna
- 8GiB eMMC

U-Boot boots chained with fastboot in 64-bit mode.
For detailed build instructions see readme.txt in board directory.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:27 -04:00
Tom Rini
40345e9ea7 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-04-01 08:17:55 -04:00
Siarhei Siamashka
7adbd1165c sunxi: Add Pine64+ support
The Pine64+ is a system based on the Allwinner A64 SoC. It is capable of
running AArch64 code and thus is the first of its kind for the sunxi target.

This patch adds a defconfig and device tree chunks for it.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: Change patch description]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Siarhei Siamashka
d96ebc468d sunxi: Add support for Allwinner A64 SoCs
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.

Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Chen-Yu Tsai
fa06f7ed11 sunxi: Enable USB nodes for H8Homlet v2
This provides the minimal changes to the H8Homlet v2 dts to enable USB
in U-boot. It is not what will be submitted to the kernel.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:25 +02:00
Chen-Yu Tsai
d02e647432 sunxi: Enable USB on Cubietruck Plus
This provides the minimal changes to the Cubietruck Plus dts to enable USB
in U-boot. It is not what will be submitted to the kernel.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:22 +02:00
Chen-Yu Tsai
b0bea66789 sunxi: Add USB and R_PIO nodes to sun8i-a83t.dtsi
This provides the minimal changes to the A83T dtsi to enable USB in
U-boot. It is not what will be submitted to the kernel.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:19 +02:00
Masahiro Yamada
67bd9bb80f ARM: uniphier: enable eMMC on PH1-sLD3 reference board
On PH1-sLD3, eMMC and NAND are assigned to different I/O pins.
Both devices can be enabled at the same time.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:59:47 +09:00
Masahiro Yamada
89d8769298 ARM: dts: uniphier: add NAND pinmux node
This will be used to set up pin-muxing for the NAND controller.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:59:47 +09:00
Masahiro Yamada
f1494981ca ARM: dts: uniphier: add clock-frequency to serial nodes of LD11/LD20
Since no clock driver is implemented for peripherals in U-Boot yet,
this property is needed for the serial driver to set up the divisor
register.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:59:22 +09:00
Tom Rini
0badc648dc Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-03-29 12:58:45 -04:00
Qianyu Gong
2ef846e45c armv8/ls1043aqds: dts: Set SPI mode for DSPI
Clock phase and polarity for DSPI flash need to be set.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:24 -07:00
Alexander Merkle
cb941e8f89 Fix typo in chosen parameter of pcm052.dts
Fix typo "choosen" instead of "chosen" in pcm052.dts.
Not tested but should fix boot process and terminal output.

Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-27 09:12:22 -04:00
Alexander Merkle
2deba805ba Fix typo in chosen parameter in vf610-twr.dts
Fix typo "choosen" instead of "chosen" in vf610-twr.dts.
Fixes boot process and terminal output for Vybrid series.

Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-27 09:12:22 -04:00
Tom Rini
a6164205ee Merge git://www.denx.de/git/u-boot-marvell 2016-03-25 12:57:18 -04:00
Stefan Roese
aea02abec5 arm: mvebu: theadorable: Add StratixV FPGA programming support
This patch adds support for Altera StratixV bitstream programming. 2 FPGAs
are connected to the SPI busses. This patch uses board specific write
code to program the bitstream via SPI direct write mode.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-03-24 09:48:34 +01:00
Tom Rini
b5b84be8a7 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-03-23 18:35:11 -04:00
Hans de Goede
72cd013293 sunxi: Add defconfig and dts for Orange Pi 2 SBC
The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.

The added dts file is identical to the one submitted to the upstream
kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
d1b7407c2f sunxi: Add defconfig and dts for Dserve DSRV9703C tablet
The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-23 22:04:13 +01:00
Hans de Goede
6b3e71a38b sunxi: Add defconfig and dts for the Polaroid MID2809PXE4 tablet
The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
c7e2ec4279 sunxi: Add defconfig and dts for Difrence DIT4350 tablet
The Difrnce dit4350 tablet is a tiny tablet with a 4.3" 16:9 480x272 LCD,
A13 SoC, 512M RAM, 4G NAND, solomon systech ssd2532qn6 touchscreen at
i2c1 address 0x48, Memsic MXC622X accelerometer at i2c1 address 0x15 and
rtl8188etv wifi.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
84842b23b7 sunxi: Add defconfig and dts for colorfly e708 q1 tablet
The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.

The added dts is identical to the dts submitted to the upstream kernel,
note this commit also syncs axp22x.dtsi and sun6i-a31.dtsi with the
upstream kernel as the added dts depends on these.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Hans de Goede
80e5f83c0f sunxi: Sync dts files with the upstream kernel
Sync dts files with the upstream kernel including
changes queued for 4.6:

https://git.kernel.org/cgit/linux/kernel/git/mripard/linux.git/commit/?h=sunxi/dt-for-4.6

Note this adds a number of new unused board dts files. I've asked the
authors of the kernel commits adding these to submit a matching defconfig
to u-boot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-03-23 22:04:13 +01:00
Masahiro Yamada
fc26b7b91d ARM: dts: uniphier: add PH1-LD11 SoC/board device tree sources
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:45:21 +09:00
Masahiro Yamada
7bdd155437 ARM: dts: uniphier: add PH1-LD20 SoC/board device tree sources
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:45:20 +09:00
Masahiro Yamada
6063498be8 ARM: dts: uniphier: add device tree for Micro Support Card
Import uniphier-support-card.dtsi from Linux Kernel and make it
available on the UniPhier reference boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-03-24 01:36:55 +09:00
Stefan Roese
93d9fc26cb arm: socfpga: sr1500: Misc updates (SPI speed, env location)
This patch makes the following changes to the SR1500 board port:

- Update defconfig to support SPI NOR (use make savedefconfig).
- Increase SPI speed to a maximum of 100MHz for faster system
  bootup.
- Change environment location, so that its not between SPL and
  main U-Boot. This way the combined SPL / U-Boot image can
  be used for updates.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
2016-03-20 18:01:11 +01:00
Przemyslaw Marczak
3349682c77 dts:exynos:update pinctrl size-cells and fix child regs
This change is required to avoid warnings about invalid
size-cells defined in device-tree pinctrl nodes for Exynos.

Tested on:
- Odroid U3
- Odroid XU3

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
2016-03-17 21:27:39 -06:00
Tom Rini
4d339a9e8a Merge branch 'master' of git://git.denx.de/u-boot-video 2016-03-15 08:01:17 -04:00
Nishanth Menon
606e4ac35e ARM: dts: k2g: Add support for PMMC
Enable support for PMMC the TI power processor on K2G. This processor
manages all power management related activities on the SoC and and
allows the Operating Systems on compute processors such as ARM, DSP to
offload the power logic away into the power processor. U-boot just has a
load responsibility, hence the view of the hardware from a bootloader
perspective is different from the view of hardware from a Operating
System perspective. While bootloader just loads up the firmware,
Operating Systems look at the resultant system as "hardware".

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:37 -04:00
Jacob Chen
cfd9794115 rockchip: dts: Add LVDS support
Add these node to be used in rockchip LVDS and VOP driver.

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-03-14 22:12:15 +01:00
Masahiro Yamada
a55d9feeec ARM: uniphier: add eMMC boot support
Export device nodes needed for eMMC boot (eMMC node, pinctrl, and
clock) to the SPL DTB.  CONFIG_SUPPORT_EMMC_BOOT is also necessary
to use "mmc partconf" command.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:16 +09:00
Masahiro Yamada
c7f94eecfd ARM: dts: uniphier: add SD/MMC host controller nodes
This host controller is available for all UniPhier SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:16 +09:00
Masahiro Yamada
595dc1e162 ARM: dts: uniphier: add GPIO controller nodes
Make the GPIO driver really active.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:15 +09:00
Masahiro Yamada
0f5fb8ce40 ARM: dts: uniphier: rework System Bus nodes
Follow the changes of DTS in Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-29 03:50:15 +09:00
Tom Rini
cdb714d7c9 Merge branch 'master' of git://git.denx.de/u-boot-socfpga 2016-02-24 18:44:19 -05:00
Tom Rini
e1417c7b66 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-02-24 18:44:15 -05:00
Marek Vasut
755ff3a38d arm: socfpga: cv_socdk: Add support for QSPI boot
Add missing DT nodes to allow booting from QSPI NOR.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
2016-02-24 19:13:03 +01:00
Marek Vasut
a1d4e962ca arm: socfpga: av_socdk: Add support for QSPI boot
Add missing DT nodes to allow booting from QSPI NOR.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Denis Bakhvalov <denis.bakhvalov@nokia.com>
2016-02-24 19:13:03 +01:00
York Sun
2f7d70082c arm: ls1021aqds: Enable driver model lpuart serial driver
Convert ls1021aqds_nor_lpuart and ls1021aqds_ddr4_nor_lpuart
to driver model suport. Enable lpuart port driver.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-24 08:40:15 -08:00
York Sun
d83b47b778 arm: ls1021aqds: Convert to driver model and enable serial support
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
2016-02-23 08:08:15 -08:00
Michal Simek
baec7df738 ARM: zynq: Add reset-gpio property for USB on Zybo
DTS syncup with Linux kernel.
Add missing reset-gpio property.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22 16:37:50 +01:00
Nathan Rossi
cb204a69d6 ARM: zynq: Enable u-boot,dm-pre-reloc for qspi
Enable u-boot,dm-pre-reloc for qspi for zc706, zed and microzed.

Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-02-22 16:21:05 +01:00
Stephen Warren
5589bc2770 ARM: tegra: enable USB device mode port on Dalmore
This allows U-Boot to expose UMS and DFU protocols on this port in device
mode, or to act as a USB host on the port, using an "OTG" (micro-B to
female A host) cable.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-18 10:02:19 -07:00
Simon Glass
91c08afe66 tegra: video: Move LCD driver to use the DM PWM driver
Use the driver-model PWM driver in preference to the old code.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:53 -07:00
Simon Glass
9e6866d3b6 tegra: video: Convert tegra20 LCD driver to driver model
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.

Boards which use this are fixed up, but only seaboard is tested.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:52 -07:00
Simon Glass
ee7d755a58 tegra: dts: Sync tegra20.dtsi with Linux v4.4
This file has changed quite a bit since it was set up. Sync it back with
Linux v4.4. Adjust the users slightly to cope with the changes:

- the host1x node is now called host1x@50000000
- we need a clocks node to provide the clk32k_in phandle
- active usb nodes need status = "okay"
- active i2c nodes need status = "okay"

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:51 -07:00
Simon Glass
300e235378 tegra: dts: Sync up nyan-big files with Linux
Sync up these files with Linux v4.4. Some differences remain, principally
that the addresses are still 32-bit in U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:50 -07:00
Simon Glass
f4abbee3ae tegra: dts: Sync up the tegra124 device tree files with Linux
Sync up these files with Linux v4.4.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-02-16 09:17:50 -07:00
Masahiro Yamada
3f23111722 ARM: uniphier: add support for PH1-Pro4 Ace and Sanji boards
Initial commit for PH1-Pro4 Ace and Sanji boards.

Note:
There are two variants for the Ace board in terms of the amount of
DDR memory; 1GB or 2GB.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 17:07:46 +09:00
Masahiro Yamada
500aacabef ARM: dts: uniphier: enable I2C channel 2 of ProXstream2 Gentil board
This is used for on-board inter-connection.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 17:07:46 +09:00
Masahiro Yamada
a65256d304 ARM: dts: uniphier: add EEPROM node for ProXstream2 Gentil board
This board has an EEPROM connected to the I2C channel 0 of the SoC.
Its slave address is 0x54.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 17:07:46 +09:00
Masahiro Yamada
49dde45ba8 ARM: dts: uniphier: add clocks properties to EHCI nodes
This allows the EHCI driver to get clocks from device tree.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 16:36:13 +09:00
Masahiro Yamada
aa37aba128 ARM: dts: uniphier: add device nodes for MIO control block
This block provides clock and reset control for MIO (Media I/O)
hardware blocks such as USB2.0, SD card, eMMC, etc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 16:36:13 +09:00
Masahiro Yamada
9fbb2f7ec6 ARM: dts: uniphier: add device nodes for Peripheral control block
This block provides clock and reset control for peripherals such as
UART, I2C, IC card, etc.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 16:36:13 +09:00
Masahiro Yamada
233812a642 ARM: dts: uniphier: add device nodes for System Control blocks
These are mainly used for controlling clocks and resets.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 16:36:13 +09:00
Masahiro Yamada
cc33609546 ARM: dts: uniphier: add reference clock nodes
Add master clock nodes generated by crystal oscillators.

  PH1-sLD3, PH1-LD4: 24.576 MHz
  PH1-Pro4, ProXstream2: 25.000 MHz
  PH1-Pro5: 20.000 MHz

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-02-14 16:36:13 +09:00
Mugunthan V N
2c5bf6c98d ARM: dts: k2g: Add keystone net dts files
Add keystone net DT support for k2g evm.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-02-08 10:10:48 -05:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Bhuvanchandra DV
f8aaade7f3 arm: pcm052: Add device tree file's
- Add device tree files for Phytec phyCORE-Vybrid Board.
- Enable lpuart support for Phytec phyCORE-Vybrid Board.
- Use UART1 for stdout.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02 21:36:09 +01:00
Bhuvanchandra DV
987dd5f7c2 arm: vf610-twr: Add device tree file's
- Add device tree files for NXP/Freescale VF610 Tower Board.
- Enable lpuart support on NXP/Freescale VF610 Tower Board.
- Use UART1 as stdout.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02 21:36:09 +01:00
Bhuvanchandra DV
c720ff12f8 arm: colibri-vf: Enable serial support
- Enable lpuart support on Toradex Colibri VF50/VF61
- Use UART0 for stdout.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02 21:36:09 +01:00
Bhuvanchandra DV
947fb97217 arm: vybrid: Update the license string
Since SPDX license is already there, drop the full one.

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02 21:36:09 +01:00
Bhuvanchandra DV
d5e4f0abad arm: vybrid: Enable lpuart support
Add device tree node's for lpuart on Vybrid platform

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-02-02 21:36:09 +01:00
Qianyu Gong
73a5de4c6e armv8/ls1043aqds: fix DSPI/QSPI node in dts file
Fix the lost dts info when merging patches.

Fix DSPI node for 'commit e0579a5852 ("armv8/ls1043aqds: add DSPI
support")' and QSPI node for 'commit 166ef1e90c ("armv8/ls1043aqds:
add QSPI support in SD boot")'.

Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-01 09:11:11 -08:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Tom Rini
19bde0316f Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-01-27 15:05:12 -05:00
Gong Qianyu
166ef1e90c armv8/ls1043aqds: add QSPI support in SD boot
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:55 -08:00
Wenbin Song
2970e14f65 armv8/ls1043aqds: Add lpuart support
Add lpuart support using the driver model.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:12 -08:00
Wenbin Song
8e728aa915 armv8/ls1043aqds: Spilt off board device tree
Move new /chosen node out of the board device tree.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:13:12 -08:00
Soren Brinkmann
0d90e9d851 ARM64: zynqmp: DT: Fix UART compatible string
ZynqMP has r1p12 not r1p8. r1p12 contains break detection support.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Punnaiah Choudary Kalluri
d3fd433f07 ARM64: zynqmp: Correct the watchdog timer interrupt number
Corrected the watchdog timer interrupt number.
Origin value was for CSUPMU watchdog.

Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
cb9dcc6eaa ARM64: zynqmp: Fix coding style in phy node
Trivial fix.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
7ebf67a34c ARM: zynq: Move spi node to aligned location
Keep nodes aligned.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:55 +01:00
Michal Simek
4691941b45 ARM: zynq: Fix all remaining zynq platform to use stdout-path
Fix console setup for all remaining zynq boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:55 +01:00
Michal Simek
e5c343dddc ARM: zynq: Clean DTSI coding style
Fix minor indentation problems.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:55 +01:00
Stefan Roese
b20c38a973 arm: mvebu: Add support for the Armada XP theadorable board
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.

Two defconfigs are added:

theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.

theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
2016-01-27 07:45:43 +01:00
Vishnu Patekar
cd7aa27bec sunxi: Add suport for A83T based Banana-pi M3 Board
Add dts and defconfig for Banana-pi M3 board.

It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Simon Glass
7c1058fadc rockchip: Add support for Raxda Rock 2
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.

So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.

Thanks to Tom Cubie for sending me a board.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
cf629bb2ba rockchip: rock2: dts: Make changes for U-Boot
Add the required pre-relocation tags and SDRAM init information for U-Boot.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
68b08c4077 rockchip: rock2: Bring in device tree files from Linux
Bring in the current device tree files for rock2 from linux/next commit
719d6c1. Hopefully this is the latest one.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
6406f45354 rockchip: dts: Sync up SPDIF node with Linux
This has been added and we have references to it in the rock2 board. Add
this node.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
74336f7daa rockchip: jerry: Enable EDP and HDMI video output
Enable these devices using the VOPL video output device. We explicitly
disable VOPB in the device tree to avoid it taking over. Since this device
has an LCD display this comes up by default. If the display fails for some
reason then it will attempt to use HDMI. It is possible to force it to fail
(and thus fall back to HDMI) by puting 'return -EPERM' at the top of
rk_edp_probe(). For now there is no easy way to select between the two.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
dae594f210 rockchip: spl: Support full-speed CPU in SPL
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
4f14d135f9 rockchip: jerry: Fix the SDRAM timing
There is a minor error in the SDRAM timing. It does not seem to affect
anything so far. Fix it just in case.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:37 -07:00
Simon Glass
27a1961d0b rockchip: jerry: Enable the Chrome OS EC
Turn on the EC and enable the keyboard.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:36 -07:00
Simon Glass
f4adc9a504 rockchip: jerry: Disable pmic-int-1 setup to avoid a hang
This hangs when activated (by probing the PMIC). Disable it for now until we
understand the root cause.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Simon Glass
79d020ee74 rockchip: Use pwrseq for MMC start-up on jerry
This is defined in the device tree in Linux. Copy over the settings so that
this can be used instead of hard-coding the reset line.

Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-21 20:42:34 -07:00
Bin Meng
665ac00c98 arm: ls1021atwr: Enable driver model lpuart serial driver
Convert ls1021atwr_nor_lpuart to driver model support. As a start,
enable lpuart serial port driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-01-20 19:10:15 -07:00
Bin Meng
8b67761437 arm: ls1021atwr: Split off board device tree
Move /chosen node out of the board device tree.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-01-20 19:10:14 -07:00
Bin Meng
f833cd6279 arm: ls1021atwr: Convert to driver model and enable serial support
Convert ls1021atwr_nor to driver model support. As a start, enable
ns16550 serial port driver.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-01-20 19:10:14 -07:00
Mugunthan V N
87a2127f9f arm: dts: dra7-evm: add tick-timer to chosen node
Specify timer2 to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:22 -07:00
Mugunthan V N
6c3401ad86 arm: dts: dra72-evm: add tick-timer to chosen node
Specify timer2 to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:22 -07:00
Mugunthan V N
d3e25aed73 arm: dts: am335x-evm: add tick-timer to chosen node
Specify timer2 to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:22 -07:00
Mugunthan V N
c7bd870462 arm: dts: am335x-boneblack: add tick-timer to chosen node
Specify which timer to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:21 -07:00
Mugunthan V N
ff9e612651 arm: dts: am437x-gp-evm: add tick-timer to chosen node
Specify which timer to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:21 -07:00
Mugunthan V N
34afc6148a arm: dts: am437x-sk-evm: add tick-timer to chosen node
Specify which timer to be used as tick-timer in chosen node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:21 -07:00
Sergey Temerkhanov
746f985add armv8: cavium: Add ThunderX 88xx board definition
This commit adds basic Cavium ThunderX 88xx board definitions and support.

Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
[trini: Drop CONFIG_SYS_GENERIC_BOARD define]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 22:25:56 +00:00
Sergey Temerkhanov
1674bd1a77 armv8: cavium: Add the device tree for ThunderX
This commit adds the FDT for the ThunderX family of SoCs

Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>

Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-19 22:25:37 +00:00
Phil Sutter
aefb8f4c32 mvebu: Support Synology DS414
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.

Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:

Device Tree
-----------

The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.

SATA Support
------------

There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(

XHCI Support
------------

There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.

EHCI Support
------------

This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.

According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.

PCIe Support
------------

This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.

DDR3 Training
-------------

Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.

PEX Init
--------

Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.

Static Environment
------------------

This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 14:08:59 +01:00
Stefan Roese
0299c90f39 arm: mvebu: Add SolidRun ClearFog Armada 38x initial support
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C

The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/

With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-14 14:08:59 +01:00
Stefan Roese
202ededd96 arm: mvebu: armada-388-gp.dts: Add ethernet aliases
Adding these aliases enables the update of the MAC addresses from
within U-Boot.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-14 14:08:59 +01:00
Stefan Roese
18c1272f99 arm: mvebu: Add armada-xp-maxbcm.dts for maxbcm board
This is needed for the upcoming ethernet DM conversion of the maxbcm
board. The configuration of the PHY is then extracted from the DT
instead of using the defines from the config header.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-14 14:08:59 +01:00
Stefan Roese
09a54c009e arm: mvebu: Add SPI driver model support
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
2016-01-14 14:08:59 +01:00
Stefan Roese
6451223a8d arm: mvebu: Add DM and OF_CONTROL support to SPL
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.

This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.

Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:

   arch/arm/cpu/u-boot-spl.lds

This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
2016-01-14 14:08:59 +01:00
Mugunthan V N
4fb01c4435 arm: dts: am4372: add qspi register maps for memory map
Add qspi memory map address to device tree.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:28 +05:30
Mugunthan V N
1f19d504cc arm: dts: dra72-evm: add spi-flash comaptible for flash
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:28 +05:30
Mugunthan V N
f7276c8615 arm: dts: dra7-evm: add spi-flash comaptible for flash
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:28 +05:30
Mugunthan V N
4416ddba5b arm: dts: am437x-gp-evm: add spi-flash comaptible for flash
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13 18:47:27 +05:30