Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All the source code of sdram_rk3036.c are from Rockchip, update the
copyright to owned by Rockchip.
Because rockchip may use this copy of code both for open source
project and internal project, update the license to use both
GPL2.0+ and BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current implementation of hab_auth_img command needs ivt_offset to
authenticate the image. But ivt header is placed at the end of image
date after padding.
This leaves the usage of hab_auth_img command to fixed size or static
offset for ivt header. New function "get_image_ivt_offset" is introduced
to find the ivt offset during runtime. The case conditional check in this
function is same as boot_get_kernel in common/bootm.c
With this variable length image e.g. FIT image with any random size can
have IVT at the end and ivt_offset option can be left optional
Can be used as "hab_auth_img $loadaddr $filesize" from u-boot script
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Using ulong is wrong as its size depends on the Host CPU architecture
(32-bit vs. 64-bit) although the Cortex-M4 is always 32-bit.
Without this patch, the stack and PC are obviously wrong and it
generates an abort when used on 64-bit processors such as the i.MX8MQ.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Otherwise can't boot the M4 core as it is impossible to load its
firmware into the TCM memory.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Currently, the DWC3 USB node is out of sync because the bindings
for the UniPhier DWC3 PHY diverged between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch changes mt7629 to use the compatible platform SMP initialization
method of linux kernel.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
For signing the tiboot3.bin image, an optional KEY file can be passed
using CONFIG_SYS_K3_KEY. Right now, Makefile scripts directly takes
the config value and uses it for signing. This is okay if the build
directory is a sub-directory of source tree, otherwise it fails.
Fix it by using the path relative to the source tree.
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
boards. At one point, the #ifdef's were replaced with
if CONFIG_IS_ENABLED but this won't work for people who need
OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
used in Kconfig. This patch moves the check to #if defined and
also makes Kconfig select the banks if CMD_GPIO is used which
makes the checks in the code less cumbersome.
Fixes: bd8a9c14c9 ("arm: mach-omap2/omap3/clock.c: Enable
all GPIO with CMD_GPIO")
Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate omap3_igep00x0.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Marvell DDR3 training code is now part of the U-Boot SPL so the
comment saying it needs porting is no longer correct.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Add a generic mailbox API for FPGA reconfig status which can be
called by others. This new function accepts 2 different mailbox
commands: CONFIG_STATUS or RECONFIG_STATUS.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Under U-boot, the WiFi SDIO Module should be disabled and the
eMMC modules should be enabled, so this patch adds an s400-u-boot.dtsi
include file specific for U-Boot that will be included by the build system.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add initial support for the Ingenic JZ47xx MIPS SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
