* convert all files cpu/../at91 to use at91_gpio driver syntax
* change AT91_PINP([A-F])(\d+) to AT91_PIO_PORT\1, \2
this makes all 160 AT91_PINPxxx defines obsolete
* AT91_PINPxxx defines and gpio.h can be remove, if all boards converted to new SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add a real AT91 GPIO driver instead of header inline code
* resolve the mixing of port and pins
* change board config files to use new driver
* add macros to gpio to realize backward compatibility
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add's the new temporary CONFIG_AT91_LEGACY to all board configs
This will need for backward compatiblity, while change the SoC access
to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated
SoC is used.
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
The EVM UI extender card has a NAND device. This change will enable
saveenv to work with NAND and Linux to be booted using:
mtdparts default
nboot kernel
bootm
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In function get_osc_clk_speed(), do not change/ update
the divider for SYS_CLK as it can has cascading effect
on the other derived clocks.
Sudden change in divider value can lead to inconsistent
behavior in the system - often leading to crashes.
The problem was found when working with OMAP3EVM using
DM3730 processor card.
The patch has been tested with OMAP3530 on OMAP3EVM as
well
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Hiremath Vaibhav <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Commit f9b6a1575d, "i.MX31: fix SPI
driver for shorter than 32 bit" broke 32 bit transfers. This patch
makes single 32 bit transfer work again.
Transfer lengths that are known not to work will abort and print
an error message.
Tested on i.MX31 Litekit and i.MX31 PDK using 32 bit transfers to
the MC13783/ATLAS chip (using the 'date' command).
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
printf goes to uart1, but it will block forever waiting for
busy to go off unless the uart is enabled first.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Previous code compiled with gcc-4.2.2 makes a call to
__aeabi_uidiv to divide by 20. As a side effect it was
not inline any more, and so sdram_cfg used the stack
as well, but this is early code that has no stack yet.
The patch explicitly removes the division, so no stack is used.
The calculation of the counter calls a division by 20
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
The structure was missing a reserved entry (not listed in the manual,
actually), so the last registers had a wrong offset. This prevented
all swlocked registers to be modified as swlock is last in the structure.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Added support for the following EDB93xx boards:
EDB9301
EDB9302
EDB9302A
EDB9307
EDB9307A
EDB93012
EDB9315
EDB9315A
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
This patch makes the crcit utility more readable
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch removes "CONFIG_CMD_JFFS" from the board config
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Every omap3 board config file declared the global variable gpmc_cfg.
This changes moves the declaration to a better location in the
arch dependent header file cpu.h.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Use appropriate GPMC timings for the LAN9221 controller on the
Gumstix Overo expansion boards not the values in arch-omap3/mem.h
which are for a different ethernet controller.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tidyup the pin muxer configuration using the Davinci table driven
pinmux configuration function and data tables.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This adds a driver for the SPI controller found on davinci
based SoCs from Texas Instruments.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for esd gmbh OTC570 board.
The OTC570 is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Commit cbb0cab1d9 broke some platforms which used kgdb code but
didn't actually include kgdb.h. So include kgdb.h in all the relevant
traps code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes a problem I've notived on a buggy PPC4xx system. This
system has problems with the PHY MDIO communication and seemed to be
stuck/crashed in miiphy_reset(). But degugging revealed, that the CPU
didn't crash, but "only" hung in this counting loop for about 2 minutes.
This patch now uses a real timeout of 0.5 seconds (as mentioned in the
comment in miiphy_reset).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The patch add support for the Freescale mx51 processor
to the FEC ethernet driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Although the datasheet mentions seperate smi registers for each
port, using Port 1 smi register to access ethernet phys does not
work. Hence only Port 0 smi register should be used to access all
devices connected to the smi bus. This behavior is consistant with
the mv643xx driver in the linux kernel.
Signed-off-by: Siddarth Gore <gores@marvell.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
ns16550 busyloops waiting for incoming byte causing watchdog to reboot
while waiting for a key press. A call to WATCHDOG_RESET in NS16550_getc
loop fixes it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
This patch changes usb_control_msg back to the state prior to commit
4886720844.
The USB driver ISR routine may update the status.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
The conversion from offsets to C structs lost a little padding in the DMA
register map. Accessing endpoints other than ep0 with DMA would fail as
the addresses wouldn't be adjusted correctly.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The EXBITGEN board has not been maintained for a long time; it has
build problems, but no hardware is available any more for testing.
Drop support for this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
This patch fixes building for AR405 boards by remove an unused feature.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The init_coupler() function from board/esd/plu405/plu405.c
got lost somehow! This patch readds it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove some unused features and default environment variable
to shrink the PMC440 u-boot.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Recently this compilation error occurs:
Configuring for ML2 board...
traps.c: In function 'MachineCheckException':
traps.c:159: error: 'debugger_exception_handler' undeclared (first use
in this function)
traps.c:159: error: (Each undeclared identifier is reported only once
traps.c:159: error: for each function it appears in.)
This patch now fixes it by including kgdb.h
Signed-off-by: Stefan Roese <sr@denx.de>
eraseregions numblocks was sometimes one less than actual, possibly producing
erase regions with zero blocks. As MTD code touches eraseregions only if
numeraseregions is greater that zero, allocate eraseregions only for non
uniform erase size flash.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
* add's at91_emac (AT91RM9200) network driver (NET_MULTI api)
* enable driver with CONFIG_DRIVER_AT91EMAC
* generic PHY initialization
* modify AT91RM9200 boards to use NET_MULTI driver
* the drivers has been tested with LXT971 Phy and DM9161 Phy at
MII and RMII interface
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
There's no sensible reason to unite speed and interface type into
one variable. So split this variable enet_interface into two
vars: enet_interface_type, which hold the interface type and speed.
Also: add the possibility for switching between 10 and 100 MBit
interfaces on the fly, when running in FAST_ETH mode.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The EMAC IP on DM365, DM646x and DA830 is slightly different
from that on DM644x. This change updates the DaVinci EMAC driver
so that EMAC becomes operational on SOCs with EMAC v2.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Enabling CONFIG_CMD_MII in AVR32 boards was not possible due to
compile errors.
This patch fixes miiphy_read and miiphy_write functions and
registers them properly.
Signed-off-by: Semih Hazar <semih.hazar@indefia.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The TSEC_FIBER flag should be set when a PHY is operating with an
external fiber interface. Currently it is only used to notify a user
that the PHY is operating in fiber mode.
A short description was also added to the other TSEC flag defines so
that it is clear how they differ from one another.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The BCM5482 PHY supports both copper and fiber as an ethernet medium.
By enabling its copper/fiber mode auto-detection feature it can
dynamically determine if it should be configured for copper or fiber.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>