Commit graph

409 commits

Author SHA1 Message Date
Purna Chandra Mandal
9ffa7a35ef drivers: ddr: Add DDR2 SDRAM controller driver for Microchip PIC32.
This driver initializes PIC32 DDR2 SDRAM controller and internal DDR2 Phy module.
DDR2 controller operates in half-rate mode (upto 533MHZ frequency).

Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-01 22:14:01 +01:00
Purna Chandra Mandal
32c1a6eef8 MIPS: initial infrastructure for Microchip PIC32 architecture
Create initial directory, Kconfigs needed for PIC32 architecture
support. Also add PIC32 specific register definition required for drivers.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-01 22:14:00 +01:00
Paul Burton
05e342554e MIPS: Support dynamic I/O port base address
The existing mips_io_port_base variable isn't suitable for use early
during boot since it will be stored in the .data section which may not
be writable pre-relocation. Fix this by moving the I/O port base address
into struct arch_global_data. In order to avoid adding this field for
all targets, make this dependant upon a new Kconfig entry
CONFIG_DYNAMIC_IO_PORT_BASE. Malta is the only board which sets a
non-zero I/O port base, so select this option only for Malta.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-02-01 22:13:25 +01:00
Paul Burton
8ac493cd65 MIPS: Remove SLOW_DOWN_IO
CONF_SLOWDOWN_IO is never set for any target, so remove the dead code in
the SLOW_DOWN_IO macro. This is done in preparation for changes to
mips_io_port_base which can be avoided in this path by removing it
entirely.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-02-01 22:13:25 +01:00
Marek Vasut
fbb0de088b mips: cache: Bulletproof the code against cornercases
This patch makes sure that the flush/invalidate_dcache_range() functions
can handle corner-case calls like this -- invalidate_dcache_range(0, 0, 0);
This call is valid and is happily produced by USB EHCI code for example.
The expected behavior of the cache function(s) in this case is that they
will do no operation, since the size is zero.

The current implementation though has a problem where such invocation will
result in a hard CPU hang. This is because under such conditions, where the
start_addr = 0 and stop = 0, the addr = 0 and aend = 0xffffffe0 . The loop
will then try to iterate over the entire address space, which in itself is
wrong. But iterating over the entire address space might also hit some odd
address which will cause bus hang. The later happens on the Atheros MIPS.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
2016-02-01 22:13:24 +01:00
Daniel Schwierzeck
e26e8dc8f4 MIPS: start.S: fix and optimize instructions
Fix 32 vs 64 bit load/store instructions. Access CP0_WATCHHI as
32 Bit register. Use 64 Bit register access for clearing gd_data
and copying U-Boot.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-02-01 22:13:24 +01:00
Purna Chandra Mandal
a62790997f MIPS: initialize board_init_f() argument to zero.
Argument boot_flags of board_init_f() should be set to 0 as
$a0 may be utilized in lowlevel_init() or mips_cache_reset()
or previous stage boot-loader.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-02-01 22:13:24 +01:00
Tom Rini
d6ea6d8876 mips: asm/io.h: Add in <linux/bug.h>
As part of the bug.h / BUILD_BUG_* clean up, this file was missed.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-25 18:52:23 -05:00
Daniel Schwierzeck
0e0efb40b8 MIPS: implement bit manipulating I/O accessors
Add support for functions clrbits_X(), setbits_X() and clrsetbits_X()
on MIPS.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
898582bdee MIPS: fix SPDX license identifier in remaining arch header files
Add a SPDX license identifier to MIPS header files where it is
still missing.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
a3ab2ae7f6 MIPS: sync processor and register definitions with linux-4.4
Update definitions for processor, registers as well as assemby
macros.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
23ff8633fd MIPS: sync I/O related header files with linux-4.4
Mainly sync asm/io.h to get a working ioremap() implementation
as well as the full set of I/O accessors. Pull in additional
header files to make this work.

Furthermore port over the directory 'arch/mips/include/asm/mach-generic/'
with contains default definitions for I/O and memory spaces and default
implementations for mapping those spaces. All files in that directory
can be overwritten by a SoC/machine.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
f53830e74e MIPS: kconfig: add option for MIPS_L1_CACHE_SHIFT
Add Kconfig symbol for L1 cache shift like the kernel does.
The value of CONFIG_SYS_CACHELINE_SIZE is not a reliable source
for ARCH_DMA_MINALIGN anymore, because it is optional on MIPS.
If CONFIG_SYS_CACHELINE_SIZE is not defined by a board, the
cache sizes are automatically detected and ARCH_DMA_MINALIGN
would be set to 128 Bytes.

The default value for CONFIG_MIPS_L1_CACHE_SHIFT is 5 which
corresponds to 32 Bytes. All current MIPS boards already used
that value. While on it, fix the Malta board to use a value of 6
like the kernel port does.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
0315a28909 MIPS: Kconfig: optimize gcc -march and -mtune setup
Move setup of -march to arch/mips/Makefile and follow the design on ARM.
Also add a possibility to chose specific CPU tune options.

Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
76ada5f8b7 MIPS: au1x00: move SoC header files to arch/mips/mach-au1x00/include/mach/
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
6479b691d7 MIPS: Kconfig: refactor machine setup
Refactor machine setup like it is done on ARM. While on it,
also support "include <mach/file.h" for machine specific
header files.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:46 +01:00
Daniel Schwierzeck
0fc13a9093 MIPS: add initial infrastructure for device-tree files
Prepare sub-folder for device-tree files. Make support for
device-tree on MIPS available in Kbuild/Kconfig.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
2016-01-16 21:06:45 +01:00
Daniel Schwierzeck
e92d9124f8 MIPS: do not build position-independent executables for SPL
SPL binaries are usually linked to a fixed address in SRAM.
Furthermore SPL binaries do not need to relocate itself. Thus
do not build them as position-independent binaries which helps
to largely reduce the size of SPL binaries.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:45 +01:00
Daniel Schwierzeck
5b6f357fe7 MIPS: create .text sub-sections for assembler functions
Put all functions coded in assembly in sub-sections of
section .text. This allows the linker to garbage collect
unused assembly functions too.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:45 +01:00
Daniel Schwierzeck
113492988b MIPS: fix annotation of _start and relocate_code
Correctly annotate _start and relocate_code as functions to
produce more readable disassembly code generated by objdump.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-01-16 21:06:45 +01:00
Purna Chandra Mandal
1a96780016 MIPS: add asm/gpio.h to fix compilation error with CONFIG_CMD_GPIO.
With CONFIG_CMD_GPIO compilation reports error.
common/cmd_gpio.c:13:22: fatal error: asm/gpio.h: No such file or directory
 #include <asm/gpio.h>
                      ^
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-16 21:06:45 +01:00
Ben Whitten
192bc6948b Fix GCC format-security errors and convert sprintfs.
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.

Simple uses of sprintf are also converted to use strcpy.

Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-14 22:11:34 -05:00
Tom Rini
250ea267d8 Merge branch 'master' of git://git.denx.de/u-boot-mips 2015-11-06 09:17:17 -05:00
Daniel Schwierzeck
347ea94e2a MIPS: bootm: use CONFIG_IS_ENABLED() everywhere
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-06 13:27:28 +01:00
Daniel Schwierzeck
2bb5b63879 MIPS: bootm: rework and fix broken bootm code
The move to 'generic board' as well as changes in the generic
bootm code broke the boot of FIT uImage's. Especially uImage's
with additional initramfs images or FDT's do not work anymore.

Refactor the bootm code to work again with the generic bootm code.

Always relocate ramdisk and FDT in step 'bootm prep' because the
generic bootm code does this only for legacy uImage's.

Move the step 'bootm cmdline' to 'bootm prep' because the Linux
kernel parameters rd_start and rd_size have to be initialized after
the relocation of the ramdisk.

Furthermore support the step 'bootm fake'.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-06 13:27:28 +01:00
Fabio Estevam
b810aa1dd1 mips: Use the generic bitops headers
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-11-05 10:52:26 -05:00
Govindraj Raja
4adcb2380c MIPS: fix syntax for fdt_chosen/initrd.
The syntax for the fdt_chosen/initrd
functions seem to deprecated in usage
from MIPS bootm implementation.

Third parameter is no more used in these api's
Refer to : include/fdt_support.h

Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
2015-08-21 15:22:41 +02:00
Chris Packham
73a4152b25 mips: Use unsigned int when reading c0 registers
In commit a18a477 (MIPS: use common code from lib/time.c) MIPS platforms
started using common the common timer functions which are based around
the fact that many platforms have a 32-bit free running counter register
that can be used see commit 8dfafdd (Introduce common timer functions).

Even MIPS64 has such a 32-bit register (some have an additional 64-bit free
running counter, but that's something for another time).

The problem is that in __read_32bit_c0_register() we read the value from
this register into an _signed_ int and as it's returned up the call
chain to timer_read_counter() it gets assigned to an unsigned long. On a
32-bit system there is no problem. On a 64-bit system odd things happen,
sign extension seems to kick in and all of a sudden if the counter
register happens to have the MSb (i.e. the sign bit) set the negative
int gets sign extended into a very large unsigned long value. This in
turn throws out things from get_ticks() up.

Update __read_32bit_c0_register() and __read_32bit_c0_ctrl_register() to
use "unsigned int res;" instead of "int res;". There seems to be little
reason to treat these register values as signed. They are either
counters (which by definition are unsigned) or are made up of various
bit fields to be interpreted as per the CPU datasheet.

Reported-by: Sachin Surendran <sachin.surendran@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
2015-08-21 15:22:41 +02:00
Daniel Schwierzeck
b11c5d1dc2 MIPS: change 'extern inline' to 'static inline'
The kernel changed it a long time ago. Also this is now broken
on gcc-5.x.

Reported-by: Andy Kennedy <andy.kennedy@adtran.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-07-02 11:29:33 +02:00
Tony Wu
49bbdae318 MIPS: fix missing semicolon in cacheops.h
Fix missing semicolon in cacheops.h introduced in commit
2b8bcc5a2 (MIPS: avoid .set ISA for cache operations)

Signed-off-by: Tony Wu <tung7970@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
2015-07-02 11:29:33 +02:00
Joe Hershberger
c9bb942e2f Move default y configs out of arch/board Kconfig
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.

Remove the configs that behave this way from the archs.

A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:

SPIFLASH
DISPLAY_BOARDINFO

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:17:55 -04:00
Joe Hershberger
a26cd04920 arch: Make board selection choices optional
By making the board selections optional, every defconfig will include
the board selection when running savedefconfig so if a new board is
added to the top of the list of choices the former top's defconfig will
still be correct.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
2015-05-12 18:10:02 -04:00
Daniel Schwierzeck
90b1c9fad7 MIPS: implement device-tree handover to Linux kernel
Add device-tree handover to Linux kernel conforming with MIPS UHI [1].
Register $a0 will be set to the reserved value -2. The address of
the device-tree blob will be stored as KSEG0 address in $a1. $a2 and
$a3 are set to zero.

[1] http://prplfoundation.org/wiki/MIPS_documentation

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-04-24 12:15:34 +02:00
Joe Hershberger
1fd92db83d net: cosmetic: Fix var naming net <-> eth drivers
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.

This cleans up the temporary hacks that were added to this interface
along with the DM support.

This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:33 -06:00
Joe Hershberger
8b2c9a7157 net: Provide a function to get the current MAC address
The current implementation exposes the eth_device struct to code that
needs to access the MAC address.  Add a wrapper function for this to
abstract away the pointer for this operation.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:10 -06:00
Masahiro Yamada
0a12e6872e generic-board: move __HAVE_ARCH_GENERIC_BOARD to Kconfig
Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-03-28 09:03:08 -04:00
Daniel Schwierzeck
eef88dfb3e MIPS: unify CPU code in arch/mips/cpu/
Unify and move code in arch/mips/cpu/mips[32|64]/ to arch/mips/cpu/.
The CPU specific config.mk files need to remain until
CONFIG_STANDALONE_LOAD_ADDR is converted to a global Kconfig symbol.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-30 14:19:58 +01:00
Daniel Schwierzeck
d9a4a6223c MIPS: move au1x00 SoC code to arch/mips/mach-au1x00
Move all au1x00 code out of arch/mips/cpu/mips32 to allow
unification of CPU code in a later patch. The reorganization
of the SoC specific header files will be done in a later patch
series.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
2015-01-30 14:19:58 +01:00
Paul Burton
f1c64a0810 MIPS: handle mips64 ST0_KX bit in mips32 start.S
In preparation for sharing a single copy of start.S between mips32 &
mips64, handle setting the KX bit of the cop0 Status register when the
mips32 start.S is built for mips64.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-30 14:19:58 +01:00
Paul Burton
ab0d002677 MIPS: handle mips64 relocs in mips32 start.S
In preparation for sharing a single copy of start.S between mips32 &
mips64, handle mips64 relocations in the mips32 start.S when built for
mips64.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-30 14:19:58 +01:00
Paul Burton
a39b1cb7f0 MIPS: use asm.h macros in mips32 start.S
Where the mips32 & mips64 implementations of start.S differ in terms of
access sizes & offsets, use the appropriate macros from asm.h to
abstract those differences away. This is in preparation for sharing a
single copy of start.S between mips32 & mips64.

The exception to this is loads of immediates to be written to the cop0
Config register, which is a 32bit register on mips64 and therefore
constants written to it can be loaded as such.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-30 14:19:57 +01:00
Paul Burton
ba21a453a5 malta: IDE support
This patch adds IDE support to the MIPS Malta board. The IDE controller
is enabled after probing the PCI bus and otherwise just makes use of
U-boot generic IDE support.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 13:11:02 +01:00
Paul Burton
8755d50706 MIPS: clear TagLo select 2 during cache init
Current MIPS cores from Imagination Technologies use TagLo select 2 for
the data cache. The architecture requires that it is safe for software
to write to this register even if it isn't present, so take the trivial
option of clearing both selects 0 & 2.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
dd7c72006e MIPS: allow systems to skip loads during cache init
Current MIPS systems do not require that loads be performed to force the
parity of cache lines, a simple invalidate by clearing the tag for each
line will suffice. Thus this patch makes the loads & subsequent second
invalidation conditional upon the CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
option, and defines that for existing mips32 targets. Exceptions are
malta where this is known to be unnecessary, and qemu-mips where caches
are not implemented.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
ca4e833cd6 MIPS: inline mips_init_[id]cache functions
The mips_init_[id]cache functions are small & only called once from a
single callsite. Inlining them allows mips_cache_reset to avoid having
to bother moving arguments around & leaves it a leaf function which is
thus able to simply keep the return address live in the ra register
throughout, simplifying the code.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
ac22feca11 MIPS: refactor cache loops to a macro
Reduce duplication by performing loops through cache tags using an
assembler macro.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
536cb7ce1a MIPS: refactor L1 cache config reads to a macro
Reduce duplication between reading the configuration of the L1 dcache &
icache by performing both using a macro which calculates the appropriate
line & cache sizes from the coprocessor 0 Config1 register.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
4a5d8898bc MIPS: unify cache initialization code
The mips32 & mips64 cache initialization code differs only in that the
mips32 code supports reading the cache size from coprocessor 0 registers
at runtime. Move the more developed mips32 version to a common
arch/mips/lib/cache_init.S & remove the now-redundant mips64 version in
order to reduce duplication. The temporary registers used are shuffled
slightly in order to work for both mips32 & mips64 builds. The RA
register is defined differently to suit mips32 & mips64, but will be
removed by a later commit in the series after further cleanup.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:01 +01:00
Paul Burton
30374f98d1 MIPS: unify cache maintenance functions
Move the more developed mips32 version of the cache maintenance
functions to a common arch/mips/lib/cache.c, in order to reduce
duplication between mips32 & mips64.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:00 +01:00
Paul Burton
2b8bcc5a2f MIPS: avoid .set ISA for cache operations
As a step towards unifying the cache maintenance code for mips32 &
mips64 CPUs, stop using ".set <ISA>" directives in the more developed
mips32 version of the code. Instead, when present make use of the GCC
builtin for emitting a cache instruction. When not present, simply don't
bother with the .set directives since U-boot always builds with
-march=mips32 or higher anyway.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-29 12:55:00 +01:00
Daniel Schwierzeck
e520023882 MIPS: add support for pre-relocation malloc
Implement MIPS specific setup of the gd_t structure to support
pre-relocation malloc. If CONFIG_SYS_MALLOC_F_LEN is specified,
a memory area will be reserved after the initial stack area and
the gd->malloc_base pointer will be initialized.

After this patch the new driver model can be used on MIPS.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:07:23 +01:00
Daniel Schwierzeck
dd82128ef5 MIPS: add support for CONFIG_SYS_INIT_SP_ADDR
Support the existing config option CONFIG_SYS_INIT_SP_ADDR on
MIPS. This allows to move the initial stack to other places
than the beginning of RAM.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:07:16 +01:00
Daniel Schwierzeck
9d638eeab7 MIPS: add Kconfig option for CONFIG_SWAP_IO_SPACE
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:06:51 +01:00
Daniel Schwierzeck
c57dafb5b4 MIPS: replace $(CPU) with Kconfig symbols
Conditionally set head-y and lib-y with boolean Kconfig symbols
for selected CPU. This deprecates the usage of the $(CPU) variable.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:06:04 +01:00
Thomas Langer
a18a477147 MIPS: use common code from lib/time.c
The common code just needs the C0_COUNT as free running counter,
without the need of writing and checking C0_COMPARE.

The function get_tbclk() is still implemented here instead of changing
all places of CONFIG_SYS_MIPS_TIMER_FREQ to CONFIG_SYS_TIMER_RATE.

The change was tested on a MIPS32 system, but as the MIPS64 code
was/is the same, this should be no problem.

Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
2015-01-21 14:02:49 +01:00
Daniel Schwierzeck
e13a50b34b MIPS: bootm: add bootstage reporting
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:02:49 +01:00
Daniel Schwierzeck
5002d8cc54 MIPS: bootm: prepare a flattened device tree for the kernel
Add the initial code to prepare a flattened device tree for
the kernel like relocating the FDT blob and fixing up the
/chosen and /memory nodes.

The final hand over to the kernel is not yet implemented. After
the community agreed on the MIPS boot interface for device trees,
the corresponding code will be added.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:02:49 +01:00
Daniel Schwierzeck
8cec725ad5 MIPS: bootm: add mem, rd_start and rd_size to kernel command line
If the user wants to boot a kernel without legacy environment,
information like memory size, initrd address and size should be
handed over to the kernel in the command line.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:02:48 +01:00
Daniel Schwierzeck
ca65e5851f MIPS: bootm: refactor preparation of Linux kernel environment
Move preparation of Linux kernel environment in a separate
function and mark it as legacy. Add a Kconfig option to make
that legacy mode configurable.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:02:48 +01:00
Daniel Schwierzeck
25fc664f40 MIPS: bootm: refactor preparation of Linux kernel command line
Move preparation of Linux kernel command line in a separate
function and mark it as legacy. Add a Kconfig option to make
that legacy mode configurable.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2015-01-21 14:02:48 +01:00
Masahiro Yamada
afc366f01b Replace <compiler.h> with <linux/compiler.h>
Including <linux/compiler.h> is enough for general use.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-12-08 09:35:46 -05:00
Daniel Schwierzeck
e19db555b4 Kbuild: introduce Makefile in arch/$ARCH/
Introduce a Makefile under arch/$ARCH/ and include it in the
top Makefile (similar to Linux kernel). This allows further
refactoringi like moving architecture-specific code out of global
makefiles, deprecating config variables (CPU, CPUDIR, SOC) or
deprecating arch/$ARCH/config.mk.

In contrary to Linux kernel, U-Boot defines the ARCH variable by
Kconfig, thus the arch Makefile can only included conditionally
after the top config.mk.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-12-08 09:35:45 -05:00
Daniel Schwierzeck
6cec63d59d MIPS: bootm: remove unused or redundant header files
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-27 16:20:37 +01:00
Daniel Schwierzeck
c9639421fd MIPS: bootm: add missing initramfs relocation
The initramfs is currently only relocated if the user calls
the bootm ramdisk subcommand. If bootm should be used without
subcommands, the arch-specific bootm code needs to implement
the relocation.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-27 16:20:37 +01:00
Daniel Schwierzeck
426f87045c MIPS: remove board.c
After all MIPS boards are switched to generic-board, the
MIPS specific board.c can be removed.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-27 16:20:37 +01:00
Daniel Schwierzeck
6d08e22aca MIPS: fix setup of initial stack frame
To get correct stack walking and backtrace functionality in gdb,
registers fp and ra should be initialized before calling board_init_f
or board_init_r. Thus allocating stack space and zeroing it as it is
currently done in board.c becomes obsolete.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-27 16:20:37 +01:00
Masahiro Yamada
56f31e872e kbuild: use SoC-specific CONFIG to descend into SoC directory
Use "obj-$(CONFIG_FOO) += foo/" where it is possible.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-23 06:49:02 -05:00
Masahiro Yamada
165ecd26f0 kbuild: Descend into SOC directory from CPU directory
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-23 06:49:02 -05:00
Masahiro Yamada
cba1da495d include: move various macros to include/linux/kernel.h
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.

In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.

Moreover, we are suffering from too cluttered include/common.h.

This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.

Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20 11:28:25 -05:00
Daniel Schwierzeck
265072ba75 MIPS: add .padding section to linker script
Commit 79fd7e649e

    MIPS: always keep all sections in u-boot ELF binary.

    Always keep all sections in u-boot ELF binary. Move all unneeded
    sections after _end to avoid allocating space in the final binary.
    Also remove .deadcode section which is now obsolete.

removed section .deadcode because the original symptoms were not
visible anymore. Unfortuneatly the binutils bug still exists.

The size of .rel.dyn section is often bigger than needed for all
entries. But objcopy only allocates space as much as required for all
reloc entries. Thus there is a gap between the last entry and
__rel_dyn_end in u-boot.bin. If u-boot is booted from RAM (e.g. in
SPL scenarios) that area could contain garbage data which could lead
to CPU exceptions during relocation.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:05 +01:00
Daniel Schwierzeck
837cad1e47 MIPS: refactor setting of compiler options
Refactor and unify all compiler settings in arch/mips/config.mk.
Also add tune flags for each supported CPU type.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:05 +01:00
Daniel Schwierzeck
aa45f75eaf MIPS: kconfig: merge targets qemu_mips and qemu_mips64
Now the user can separately select the CPU type. Thus the
targets qemu_mips and qemu_mips64 can be merged to a single
target.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:04 +01:00
Daniel Schwierzeck
b9863b6de2 MIPS: kconfig: globally define CONFIG_SYS_CPU for MIPS
Now the user can select the CPU type for each target. Thus
CONFIG_SYS_CPU could be set globally.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:04 +01:00
Daniel Schwierzeck
02611cbb7c MIPS: kconfig: add options for CPU type select
Add new Kconfig option to let the user select the targets
CPU type. Each target have to select SUPPORTS_CPU_MIPS[32,64]_R[1,2]
to indicate which CPU types are supported.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:18:03 +01:00
Daniel Schwierzeck
0e1dc3456f MIPS: kconfig: add options for endianess select
Add new Kconfig option to let the user select the targets
endianess. Each target have to select SUPPORTS_BIG_ENDIAN
and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess
is supported.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01 18:17:22 +01:00
Masahiro Yamada
7bfd5ee117 mips: enable CONFIG_USE_PRIVATE_LIBGCC by default
Without the private libgcc, we need a full multilib toolchain with
different libgcc or multiple toolchains to build all BE/LE and
hard-float/soft-float variants of MIPS boards.  That is not feasible.

This commit allows us to build all the MIPS boards with a single
kernel.org toolchain:

https://www.kernel.org/pub/tools/crosstool/files/bin/x86_64/4.9.0/
x86_64-gcc-4.9.0-nolibc_mips-linux.tar.xz

This change sounds reasonable for most users.  If necessary,
you can disable this option via "make menuconfig" or friends.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-10-23 13:19:15 -04:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Masahiro Yamada
90f984e397 kconfig: delete redundant CONFIG_${ARCH} definition
CONFIG_${ARCH} is defined by Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 14:42:02 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
York Sun
2a1680e30e common/board_f: Initialized global data for generic board
Some platforms (tested on mpc85xx, mpc86xx) use global data before calling
function baord_inti_f(). The data should not be cleared later. Any arch
which uses global data in generic board board_init_f() should define
CONFIG_SYS_GENERIC_GLOBAL_DATA.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Simon Glass <sjg@chromium.org>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
2014-05-12 15:20:05 -04:00
Masahiro Yamada
8e2615752e bd_info: remove bi_barudrate member from struct bd_info
gd->bd->bi_baudrate is a copy of gd->baudrate.

Since baudrate is a common feature for all architectures,
keep gd->baudrate only.

It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
2014-05-12 15:19:45 -04:00
Daniel Schwierzeck
538cf92c8c MIPS: drop incaip board
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-04-20 13:16:43 +02:00
Paul Burton
9f0868fffb MIPS: allow use of generic board
This patch allows MIPS boards to make use of generic board, replacing
arch/mips/lib/board.c with common/board_{f,r}.c and struct bd_info with
the asm-generic version.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-20 13:16:43 +02:00
Paul Burton
a0af08b9db MIPS: define __init_end in u-boot.lds
The generic board code uses the __init_end symbol to calculate
monitor_flash_len. Define said symbol for MIPS, equivalent to
__image_copy_end which is used for the same purpose in
arch/mips/lib/board.c.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-20 13:16:43 +02:00
Paul Burton
11a932fb18 MIPS: move mips_io_port_base out of board.c
Move the definition of this variable out of arch/mips/lib/board.c in
preparation for allowing use of generic board on MIPS, which will lead
to this file not being compiled.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-20 13:16:42 +02:00
Paul Burton
186d8159f6 MIPS: stub interrupt_init function
interrupt_init is called unconditionally by the generic board code.
Define a stub for it on MIPS like the enable & disable functions.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2014-04-20 13:16:42 +02:00
Masahiro Yamada
7e3d473b5e mips: xburst: remove remainders of dead board
Commit 54e458de deleted qi_lb60 board support
because of the incompatible license issue.

There is no board with XBurst CPU.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-04-20 13:16:42 +02:00
Daniel Schwierzeck
79fd7e649e MIPS: always keep all sections in u-boot ELF binary.
Always keep all sections in u-boot ELF binary. Move all unneeded
sections after _end to avoid allocating space in the final binary.
Also remove .deadcode section which is now obsolete.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-04-20 13:16:42 +02:00
Stephen Warren
eb838e7d84 usb: create common header virtual root hub descriptors
Many USB host controller drivers contain almost identical copies of the
same virtual root hub descriptors. Put these into a common file to avoid
duplication.

Note that there were some very minor differences between the descriptors
in the various files, such as:

- USB 1.0 vs. USB 1.1
- Manufacturer/Device ID
- Max packet size
- String content

I assume these aren't relevant.

Cc: Thomas Lange <thomas@corelatus.se>
Cc: Shinya Kuribayashi <skuribay@pobox.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Eric Millbrandt <emillbrandt@coldhaus.com>
Cc: Pierre Aubert <p.aubert@staubli.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Zhang Wei <wei.zhang@freescale.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Markus Klotzbuecher <mk@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: C Nauman <cnauman@diagraph.com>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Thomas Abraham <t-abraham@ti.com>
Cc: Tom Rini <trini@ti.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Cc: Matej Frančeškin <matej.franceskin@comtrade.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-03-10 18:53:36 +01:00
Masahiro Yamada
cfda6bd2d8 mips: move CONFIG_MIPS{32, 64} definition to config.mk
All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.

CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-03-07 10:59:06 -05:00
Masahiro Yamada
a0a15b441c config.mk: specify the exact path to standalone linker script
We want to change the build system to include config.mk
only from ./Makefile and spl/Makefile.
We must prepare for that in this commit.

$(src) is a moving target and not handy for our purpose.
We must replace it with a fixed path.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-03-07 10:59:06 -05:00
Masahiro Yamada
cd2e46cb38 kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.

We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.

By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)

Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.

It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding

  #ifdef CONFIG_SPL_BUILD
  # define CONFIG_USE_PRIVATE_LIBGCC
  #endif

to include/configs/tegra-common.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-03-07 10:59:06 -05:00
Tom Rini
32907339c2 Merge branch 'master' of git://git.denx.de/u-boot-mips 2014-03-04 18:13:06 -05:00
Daniel Schwierzeck
37f93f7b79 MIPS: fix types u64 and __u64 to unsigned long long
Linux MIPS uses asm-generic/int-ll64.h in asm/types.h.
Thus u64 and __u64 are defined as unsigned long long. Port this
over to U-Boot.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-03-04 23:18:00 +01:00
Masahiro Yamada
9b6e2c363f kbuild: fix CROSS_COMPILE settings in config.mk
The syntax
  CROSS_COMIPLE ?= <cross_compiler_prefix>
does not work because config.mk is parsed after
exporting CROSS_COMPILE.

Like Linux Kernel's arch/$(ARCH)/Makefile,
we must write as follows:

  ifeq ($(CROSS_COMPILE),)
  CROSS_COMPILE := <cross_compiler_prefix>
  endif

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-03-04 12:15:30 -05:00
Masahiro Yamada
95ddcd68ab kbuild: rename OBJCFLAGS to OBJCOPYFLAGS
Rename OBJCFLAGS to OBJCOPYFLAGS beforehand to use
"cmd_objcopy" in scripts/Makefile.lib in an upcoming commit.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-25 11:01:28 -05:00
Masahiro Yamada
9e4140329e kbuild: change out-of-tree build
This commit changes the working directory
where the build process occurs.

Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.

That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
  $(obj)u-boot.bin:  $(obj)u-boot

Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.

And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.

On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.

The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.

Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
2014-02-19 11:07:50 -05:00
Paul Burton
bea12b7823 malta: enable PIIX4 SERIRQ
Whilst U-boot does not require this itself, Linux currently relies upon
it having been muxed and enabled by the bootloader. Thus in order to
preserve compatibility with current kernels before a fix is merged in
Linux we will enable the SERIRQ interrupt and mux it to its pin.

Without doing this current kernels will never receive serial port
interrupts and the end result is typically that userland appears to
hang.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-26 21:49:34 +01:00
Paul Burton
d18d49d7ad mips: don't hardcode Malta env baudrate
The baudrate passed to Linux in the environment was hardcoded at 38400.
Instead pass the correct baudrate from global data, allowing Linux to
correctly inherit the baudrate used by U-boot when console setup is not
explicitly specified.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-26 21:49:17 +01:00
Gabor Juhos
10473d0490 malta: use unmapped flash base address
The physical base address of the NOR flash is 0x1e000000
on the Malta boards. The hardware also maps the first 4MiB
of the flash into the 0x1fc00000-0x1fffffff range.

Currently, U-Boot uses the mapped address to access the
flash, which does not work in recent qemu versions.

Since commit a427338b222b43197c2776cbc996936df0302f51
(mips_malta: correct reading MIPS revision at 0x1fc00010)
writing to the mapped address space causes a CPU exception.
Due to the exception, U-Boot hangs during boot when it tries
to detect the CFI flash chip.

Use the correct physical address for the MALTA_FLASH_BASE
constant to fix the problem. In order to avoid relocation
problems, also update the CONFIG_SYS_{TEXT,MONITOR}_BASE
constants.

The change makes it possible to start U-Boot on a Malta
board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also
works on older versions (tested with 1.1.1, 1.2.2, 1.4.2,
1.5.3).

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
2013-11-15 11:16:59 +01:00
Paul Burton
a3e80904fb malta: arch/mips/include/asm/malta.h SPDX license tag
This patch replaces the GPL-2.0 text with a GPL-2.0
SPDX-License-Identifier tag, and adds Imagination Technologies copyright
following my recent changes.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-11 12:32:58 +01:00
Paul Burton
81f98bbd62 malta: setup PIIX4 interrupt route
Without setting up the PIRQ[A:D] interrupt routes, PCI interrupts will
be left disabled. Linux does not set up this routing but relies upon it
having been set up by the bootloader, reading back the IRQ lines which
the PIRQ[A:D] signals have been routed to.

This patch routes PIRQA & PIRQB to IRQ 10, and PIRQC & PIRQD to IRQ 11.
This matches the setup used by YAMON.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:02 +01:00
Paul Burton
e0ada6319b malta: display "U-boot" on the LCD screen
Displaying a message on the LCD screen is a simple yet effective way to
show the user that the board has booted successfully.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Paul Burton
baf37f06c5 malta: support for coreFPGA6 boards
This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.

Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.

Tested on:
  - A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
    with and without an L2 cache.
  - QEMU.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Paul Burton
7a9d109b00 qemu-malta: rename to just "malta"
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Paul Burton
fa476f75bf mips32: detect L1 cache sizes if they're not defined
For boards such as the MIPS Malta with an FPGA core card it is desirable
to be able to detect the L1 cache sizes at runtime, since they are not
dependant upon the board but on the FPGA bitstream in use. This patch
performs that detection when the CONFIG_SYS_[DI]CACHE_SIZE macros are
not defined by the board configuration. In cases where the sizes are
detected this patch also removes the restriction that the I-cache &
D-cache line sizes must be the same, as this is not necessarily true.

If the cache sizes are defined by a configuration then they will be
hardcoded as before, so this patch will not add overhead to such
boards.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2013-11-09 17:21:01 +01:00
Masahiro Yamada
643aae1406 include: delete include/linux/config.h
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)

We don't need to provide Linux copatibility any more.

This commit deletes include/linux/config.h
and fixes source files not to include this.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08 15:25:13 -05:00
Masahiro Yamada
0f0f75774e cosmetic: remove empty lines at the top of file
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-08 09:41:37 -05:00
Masahiro Yamada
f6e2c0f3e3 mips: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-10-31 13:26:45 -04:00
Troy Kisky
06d513ecb6 usb: add enum usb_init_type parameter to usb_lowlevel_init
This parameter will later be used to verify OTG ports.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-10-20 23:45:26 +02:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Daniel Schwierzeck
4b17645d5d MIPS: bootm: drop obsolete Qemu specific bootm implementation
The Qemu specific bootm implementation was intended for a special
Qemu target in Linux kernel. But this target has been dropped in
v2.6.25-rc1 by commit 302922e5f6901eb6f29c58539631f71b3d9746b8

    Author: Ralf Baechle <ralf@linux-mips.org>
    Date:   Tue Jan 29 10:15:02 2008 +0000

    [MIPS] Qemu: Remove platform.

    The Qemu platform was originally implemented to have an easily supportable
    platform until Qemu reaches a state where it emulates a real world system.
    Since the latest release Qemu is capable of emulating the MIPSsim and
    Malta platforms, so this goal has been reached.  The Qemu plaform is also
    rather underfeatured so less useful than a Malta emulation.

Thus the special bootm implementation is obsolete by now and can be
dropped. The Qemu support in U-Boot is going to be replaced by MIPS Malta
board support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
b87493f49a MIPS: bootm: add YAMON style Linux preparation/jump code for Qemu Malta
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
6c154552b0 MIPS: bootm: add support for generic relocation of init ramdisks
All linux kernels after v2.6 require a page-aligned location of
an external init ramdisk. Enable CONFIG_SYS_BOOT_RAMDISK_HIGH to
support this with the generic U-Boot relocation code.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
15f8aa9093 MIPS: bootm: refactor initialisation of kernel environment
Move initialisation of Linux environment to separate functions.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
59e8cbdb15 MIPS: bootm: refactor initialisation of kernel cmdline
Move initialisation of Linux command line to separate functions.
Also add support for bootm subcommand 'cmdline'.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
f66cc1e348 MIPS: bootm: add support for LMB
This is required for init ramdisk relocation and device tree
support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
c4b37847d3 MIPS: bootm: optimize kernel entry call
Fix signature of kernel entry function. Mark the kernel entry
with __noreturn for better code optimisation.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Daniel Schwierzeck
45bde489e3 MIPS: bootm: fix checkpatch.pl warnings
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-08-13 11:58:48 +02:00
Gabor Juhos
db2c86d7d7 MIPS: mips32/cache.S: use v1 register for indirect function calls
Synchronize the code with mips64/cache.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:07 -04:00
Gabor Juhos
ee8b1e2959 MIPS: mips32/cache.S: store cache line size in t8 register
Synchronize the code with mips64/cache.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:07 -04:00
Gabor Juhos
c325916563 MIPS: mips32/cache.S: save return address in t9 register
Synchronize the code with mips64/cache.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:06 -04:00
Gabor Juhos
d707e5b713 MIPS: xburst/start.S: rework relocation info check
Make it similar to the code in mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:06 -04:00
Gabor Juhos
e5c868a208 MIPS: xburst/start.S: use t8 register for dynamic relocation
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:06 -04:00
Gabor Juhos
f01d693535 MIPS: xburst/start.S: save gd in s0 register
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:06 -04:00
Gabor Juhos
ba9cf07122 MIPS: xburst/start.S: save relocation offset in s1 register
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:06 -04:00
Gabor Juhos
9a28e0d177 MIPS: xburst/start.S: save relocation address in s2 register
Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:05 -04:00
Gabor Juhos
691995f9ab MIPS: mips32/start.S: rework relocation info check
Make it similar to the code in mips64/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:05 -04:00
Gabor Juhos
680cb2dc3a MIPS: mips32/start.S: use t8 register for dynamic relocation
Synchronize the code with mips64/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:05 -04:00
Gabor Juhos
da84f33b04 MIPS: mips32/cache.S: remove superfluous register assignment
The t4 register already holds the cache
line size, and the value of the register
is not changed in mips_init_icache.

Get the cache line size value from t4 for
mips_init_dcache as well and remove the
superfluous assignment of t5 register.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
2013-07-24 09:51:05 -04:00
Gabor Juhos
b1591ec246 MIPS: mips64/interrupt.c: remove superfluous include
Nothing is used from asm/mipsregs.h.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:05 -04:00
Gabor Juhos
c3e4901fc6 MIPS: mips32/time.c: fix checkpatch errors/warnings
Checking mips32/time.c with checkpatch.pl shows this:

  arch/mips/cpu/mips32/time.c:30: WARNING: line over 80 characters
  arch/mips/cpu/mips32/time.c:57: ERROR: return is not a function, parentheses are not required
  total: 1 errors, 1 warnings, 0 checks, 85 lines checked

Fix the code to make checkpatch.pl happy.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:04 -04:00
Gabor Juhos
ac12984de8 MIPS: qemu-malta: setup GT64120 registers as done by YAMON
Move the GT64120 register base to 0x1be00000
and setup PCI BAR registers as done by the
original YAMON bootloader.

This is needed for running Linux kernel.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:04 -04:00
Gabor Juhos
52caee0f36 MIPS: qemu-malta: enable flash support
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:04 -04:00
Gabor Juhos
015643152a MIPS: qemu-malta: add reset support
The MIPS Malta board has a SOFTRES register. Writing a
magic value into that register initiates a board reset.

Use this feature to implement reset support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:03 -04:00
Gabor Juhos
5a4dcfac1e MIPS: qemu-malta: add support for emulated MIPS Malta board
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.

This is enough to boot U-Boot to the command prompt
both in little and big endian mode.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:03 -04:00
Gabor Juhos
843a76b66b MIPS: start.S: emulate REVISION register for qemu-malta
On the origial Malta boards the REVISION register is
accessible at the 0x1fc00010 address. The contents of
this register gives information about the revision
of the Malta and Core Boards.

This register is used by the Linux kernel to identify
the actual board it is running on. However the register
is not emulated properly by Qemu, so put a hardcoded
value into the flash to make Linux work.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-07-24 09:51:03 -04:00
Tom Rini
518d438537 MIPS: mips64: fix typos in copyright text of start.S
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

Conflicts:

	arch/mips/cpu/mips64/start.S

Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:50:52 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Dirk Eibach
b8eee4354f Build arch/$ARCH/lib/bootm.o depending on CONFIG_CMD_BOOTM
MAKEALL is fine for ppc4xx and mpc85xx.
Run checks were done on our controlcenterd hardware.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-07-16 17:44:30 -05:00
Daniel Schwierzeck
e1208c2fe5 MIPS: asm/errno.h: switch to asm-generic/errno.h
This fixes several warnings like

In file included from ./u-boot/include/linux/mtd/mtd.h:13:0,
                 from env_onenand.c:37:
./u-boot/build/vct_platinumavc_onenand_small/include2/asm/errno.h:52:0: warning: "ENOMSG" redefined [enabled by default]

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-06-08 23:10:10 +02:00
Gabor Juhos
f0550f87f4 MIPS: fix __raw_* IO accessors
The purpose of the __raw* IO accessors is to provide
IO access in native-endian order. However in the current
MIPS implementation, the 16 and 32 bit variants of the
__raw accessors are swapping the values on big-endian
systems if the CONFIG_SWAP_IO_SPACE option is enabled.

The patch changes the IO accessor macros to fix this
broken behaviour.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-06-08 23:10:10 +02:00
Andreas Bießmann
d2eae43ba8 lib: consolidate hang()
Delete all occurrences of hang() and provide a generic function.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01 16:41:08 -04:00
Tom Rini
0ce033d258 Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end.  We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.

Conflicts:
	arch/arm/cpu/ixp/u-boot.lds
	arch/arm/cpu/u-boot.lds
	arch/arm/lib/Makefile
	board/actux1/u-boot.lds
	board/actux2/u-boot.lds
	board/actux3/u-boot.lds
	board/dvlhost/u-boot.lds
	board/freescale/mx31ads/u-boot.lds
	doc/README.scrapyard
	include/configs/tegra-common.h

Build tested for all of ARM and run-time tested on am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-18 14:37:18 -04:00
Simon Glass
716cc8cc7f Change stub example to use asm-generic/sections.h
We can use the declarations of __bss_start and _end from this header
instead of declaring them locally.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-15 16:13:58 -04:00
Simon Glass
1865286466 Introduce generic link section.h symbol files
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.

Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.

One change is needed in arch/avr32/lib/board.c to make this conversion
work.

Reviewed-by: Tom Rini <trini@ti.com> (version 5)
Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-15 16:13:58 -04:00
Albert ARIBAUD
ef123c5253 Refactor linker-generated arrays
Refactor linker-generated array code so that symbols
which were previously linker-generated are now compiler-
generated. This causes relocation records of type
R_ARM_ABS32 to become R_ARM_RELATIVE, which makes
code which uses LGA able to run before relocation as
well as after.

Note: this affects more than ARM targets, as linker-
lists span possibly all target architectures, notably
PowerPC.

Conflicts:
	arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds
	arch/arm/cpu/arm926ejs/spear/u-boot-spl.lds
	arch/arm/cpu/armv7/omap-common/u-boot-spl.lds
	board/ait/cam_enc_4xx/u-boot-spl.lds
	board/davinci/da8xxevm/u-boot-spl-da850evm.lds
	board/davinci/da8xxevm/u-boot-spl-hawk.lds
	board/vpac270/u-boot-spl.lds

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-03-12 23:28:40 +01:00
Daniel Schwierzeck
455fbfb668 MIPS: board.c: remove manual relocation of env_name_spec
Remove the manual relocation of env_name_spec. This has been missed
in the previous patch series for introducing dynamic relocation
on MIPS.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-15 18:00:04 +01:00
Gabor Juhos
04380c651a MIPS: add dynamic relocation support
The code handles relocation entries with the
following relocation types only:
  mips32: R_MIPS_REL32
  mips64: R_MIPS_REL+R_MIPS_64
  xburst: R_MIPS_REL32

Other relocation entries are skipped without
processing. The code must be extended if other
relocation types must be supported.

Add -pie to LDFLAGS_FINAL to generate the .rel.dyn
fixup table, which will be applied to the relocated
image before transferring control to it.

The CONFIG_NEEDS_MANUAL_RELOC is not needed
after the patch, so remove that as well.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:13 +01:00
Gabor Juhos
0ba8926e08 MIPS: u-boot.lds: add relocation specific sections
This section contain the table needed for dynamic
relocation. Also provide symbols for the relocation
code to access the table.

Discard all sections which are not needed in the final
ELF binary and U-Boot image. Section .dynsym cannot be
discarded or GNU ld crashes otherwise. This section
will be stripped by GNU objcpy in a later patch.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:13 +01:00
Daniel Schwierzeck
28875e2c47 MIPS: start.S: use symbol __image_copy_end for U-Boot image relocation
Use the newly introduced symbol __image_copy_end as end address for
relocation of U-Boot image. This is needed for dynamic relocation added
in later patches. This patch obsoletes the symbols uboot_end and
uboot_end_data which are removed.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:13 +01:00
Daniel Schwierzeck
696a3b2a53 MIPS: start.S: optimize BSS initialization
Get the start and end address for clearing BSS from the newly
introduced symbols __bss_start and __bss_end. After GOT is
relocated, those symbols are already pointing to the correct
addresses.

Also optimize the loop by moving the address incrementation
to the delay slot to avoid the initial sub instruction.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:13 +01:00
Daniel Schwierzeck
eea8a320e1 MIPS: board.c: switch to new symbols __bss_end and __image_copy_end
Use the newly introduced symbols __image_copy_end and __bss_end
for setting up the memory area for the relocated U-Boot.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:12 +01:00
Daniel Schwierzeck
3420bf1ca0 MIPS: u-boot.lds: introduce symbol __image_copy_end
This symbol is used in later patches as end address
for relocation of the U-Boot image into RAM.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:12 +01:00
Daniel Schwierzeck
a52852c5a6 MIPS: u-boot.lds: merge all BSS sections and introduce symbols __bss_[start|end]
These symbols are used in later patches for as addresses for
clearing the BSS area in the relocated U-Boot image.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:12 +01:00
Gabor Juhos
45397816b2 MIPS: compute num_got_entries from .got section's size
The '__got_start' and '__got_end' symbols are used
only in the linker script to compute the value of
the 'num_got_entries' symbol.

Remove the symbols and use the SIZEOF(.got) command
to get the size of the .got section.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-02-12 22:22:12 +01:00
Daniel Schwierzeck
8b1c7345c6 MIPS: start.S: unify and simplify reset vector handling
Adopt reset vector handling from Yamon.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:12 +01:00
Daniel Schwierzeck
4dc7412afa MIPS: start.S: remove obsolete 64 bit handling in setup_c0_status
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2013-02-12 22:22:12 +01:00
Daniel Schwierzeck
97b920dab1 MIPS: xburst: fix broken access to global_data
Fix access to global_data which is broken since commits:

commit 035cbe99cd
Author: Simon Glass <sjg@chromium.org>
Date:   Thu Dec 13 20:49:08 2012 +0000

    mips: Move per_clk and dev_clk to arch_global_data

    Move these field into arch_global_data and tidy up. The other
    CONFIG_JZSOC fields are used by various architectures, so just remove
    the #ifdef bracketing for these.

    Signed-off-by: Simon Glass <sjg@chromium.org>

commit 582601da2f
Author: Simon Glass <sjg@chromium.org>
Date:   Thu Dec 13 20:48:35 2012 +0000

    arm: Move lastinc to arch_global_data

    Move this field into arch_global_data and tidy up.

    Signed-off-by: Simon Glass <sjg@chromium.org>

commit 66ee692347
Author: Simon Glass <sjg@chromium.org>
Date:   Thu Dec 13 20:48:34 2012 +0000

    arm: Move tbl to arch_global_data

    Move this field into arch_global_data and tidy up.

    Signed-off-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
2013-02-12 22:22:12 +01:00
Simon Glass
9572202026 mips: Use generic global_data
Move mips over to use generic global_data.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-04 09:05:45 -05:00
Simon Glass
035cbe99cd mips: Move per_clk and dev_clk to arch_global_data
Move these field into arch_global_data and tidy up. The other
CONFIG_JZSOC fields are used by various architectures, so just remove
the #ifdef bracketing for these.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-04 09:05:44 -05:00
Simon Glass
582601da2f arm: Move lastinc to arch_global_data
Move this field into arch_global_data and tidy up.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01 15:07:50 -05:00
Simon Glass
66ee692347 arm: Move tbl to arch_global_data
Move this field into arch_global_data and tidy up.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01 15:07:50 -05:00
Simon Glass
5cb48582ac Add architecture-specific global data
We plan to move architecture-specific data into a separate structure so
that we can make the rest of it common.

As a first step, create struct arch_global_data to hold these fields.
Initially it is empty.

This patch applies to all archs at once. I can split it if this is really
a pain.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01 15:07:49 -05:00
Gabor Juhos
cb5dbca899 MIPS: add unified u-boot.lds file
The patch adds an unified linker script file which
can be used for all currently supported MIPS targets.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Stefan Roese <sr@denx.de>
2013-01-31 00:26:59 +01:00
Gabor Juhos
9950b90d38 MIPS: remove OUTPUT_FORMAT from linker scripts
The OUTPUT_FORMAT command in linker scripts
was always misused due to some endianess and
toolchain problems.

Use GCC flags to ensure proper output format,
and get rid of the OUTPUT_FORMAT commands in
the board specific u-boot.lds files.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
2013-01-30 23:34:10 +01:00
Gabor Juhos
6d86227880 MIPS: xburst: simplify relocation offset calculation
The current code uses four instructions and a
temporary register to calculate the relocation
offset and to adjust the gp register.

The relocation offset can be calculated directly
from the CONFIG_SYS_MONITOR_BASE constant and from
the destination address. The resulting offset can
be used to adjust the gp pointer.

This approach makes the code a bit simpler because
it needs two instructions only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
2013-01-30 23:33:27 +01:00
Gabor Juhos
025f2b3380 MIPS: simplify relocated _G_O_T_ address calculation
The difference between the address of the original
and the relocated _GLOBAL_OFFSET_TABLE_ is always
the same as the relocation offset.

The relocation offset is already computed and it is
available in the 's1/t6' register. Use that to adjust
the relocated _G_O_T_ address, instead of calculating
the offset again from the _gp value.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Xiangfu Liu <xiangfu@openmobilefree.net>
2013-01-30 23:32:52 +01:00
Gabor Juhos
67d80c9f97 MIPS: start.S: don't save flush_cache parameters in advance
Saving the parameters in advance unnecessarily complicates
the code. The destination address is already saved in the
's2' register, and that register is not clobbered by the
copy loop. The size of the copied data can be computed
after the copy loop is done.

Change the code to compute the size parameter right
before calling flush_cache, and set the destination
address parameter in the delay slot of the actuall
call.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27 16:40:15 +01:00
Gabor Juhos
248fe03f53 MIPS: start.S: simplify relocation offset calculation
The current code uses four instructions and a
temporary register to calculate the relocation
offset and to adjust the gp register.

The relocation offset can be calculated directly
from the CONFIG_SYS_MONITOR_BASE constant and from
the destination address. The resulting offset can
be used to adjust the gp pointer.

This approach makes the code a bit simpler because
it needs two instructions only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27 16:40:07 +01:00
Gabor Juhos
b2fe86f887 MIPS: start.S: save reused arguments earlier in relocate_code
Save the reused parameters at the beginning
of the 'relocate_code' function. This makes
the function a bit more readable.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27 16:39:59 +01:00
Gabor Juhos
f321b0f99f MIPS: start.S: set sp register directly
The current code uses two instructions to load
the stack pointer into the 'sp' register.

This results in the following assembly code:

    468:   3c088040        lui     t0,0x8040
    46c:   251d0000        addiu   sp,t0,0

The first instuction loads the stack pointer into
the 't0' register then the value of the 'sp' register
is computed by adding zero to the value of the 't0'
register. The same issue present on the 64-bit version
as well:

    56c:   3c0c8040        lui     t0,0x8040
    570:   659d0000        daddiu  sp,t0,0

Change the code to load the stack pointer directly
into the 'sp' register. The generated code is functionally
equivalent to the previous version but it is simpler.

  32-bit:
    468:   3c1d8040        lui     sp,0x8040

  64-bit:
    56c:   3c1d8040        lui     sp,0x8040

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27 16:39:51 +01:00
Gabor Juhos
5b7dd8163d MIPS: start.S: fix boundary check in relocate_code
The loop code copies more data with one than
necessary due to the 'ble' instuction. Use the
'blt' instruction instead to fix that.

Due to the lack of suitable hardware the Xburst
specific code is compile tested only. However the
change is quite obvious.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-27 16:39:43 +01:00
Gabor Juhos
14fdd1a8bf MIPS: start{, 64}.S: fill branch delay slots with NOP instructions
The romReserved and romExcHandle handlers are
accessed by a branch instruction however the
delay slots of those instructions are not filled.

Because the start.S uses the 'noreorder' directive,
the assembler will not fill the delay slots either,
and leads to the following assembly code:

  0000056c <romReserved>:
   56c:   1000ffff        b       56c <romReserved>

  00000570 <romExcHandle>:
   570:   1000ffff        b       570 <romExcHandle>

In the resulting code, the second branch instruction
is placed into the delay slot of the first branch
instruction, which is not allowed on the MIPS
architecture.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22 21:09:34 +01:00
Gabor Juhos
0ef48d4c89 MIPS: convert IO port accessor functions to 'static inline'
The currently used 'extern inline' directive causes
the following compiler warnings if CONFIG_SWAP_IO_SPACE
is defined:

  <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outlc_p' which is not static [enabled by default]
  <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outl_p' which is not static [enabled by default]
  <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outlc' which is not static [enabled by default]
  <...>/include/asm/io.h:345:1: warning: '__fswab32' is static but used in inline function '__outl' which is not static [enabled by default]
  <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outwc_p' which is not static [enabled by default]
  <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outw_p' which is not static [enabled by default]
  <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outwc' which is not static [enabled by default]
  <...>/include/asm/io.h:344:1: warning: '__fswab16' is static but used in inline function '__outw' which is not static [enabled by default]
  <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inlc_p' which is not static [enabled by default]
  <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inl_p' which is not static [enabled by default]
  <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inlc' which is not static [enabled by default]
  <...>/include/asm/io.h:341:1: warning: '__fswab32' is static but used in inline function '__inl' which is not static [enabled by default]
  <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inwc_p' which is not static [enabled by default]
  <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inw_p' which is not static [enabled by default]
  <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inwc' which is not static [enabled by default]
  <...>/include/asm/io.h:340:1: warning: '__fswab16' is static but used in inline function '__inw' which is not static [enabled by default]

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22 21:07:19 +01:00
Gabor Juhos
be002d0070 MIPS: use inline directive for __in*s functions
All other IO accessor functions are using the
'inline' directive. Use that also for the __in*s
to make it consistent with the other variants.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-22 20:52:08 +01:00
Gabor Juhos
9c170e2ef4 MIPS: bootm.c: add support for 'prep' and 'go' subcommands
The bootm command supports subcommands since long time
however those subcommands are not yet usable on MIPS.

The patch is based on the ARM implementation, and it adds
support for the 'prep' and 'go' subcommands only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-16 10:52:07 +01:00
Gabor Juhos
0ea7213f63 MIPS: bootm.c: separate environment initialization
Move the environment initialization code into a
separate function. This make the code reusable
for bootm subcommands.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-16 10:52:07 +01:00
Gabor Juhos
e08634c7bf MIPS: bootm.c: separate linux jump code
Move the actual jump code into a separate function.
This make the code reusable for bootm subcommands.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2013-01-16 10:52:07 +01:00
Gabor Juhos
75a279c8f2 MIPS: bootm.c: use debug macro to print debug message
The '## Transferring control ...' message is printed
only if DEBUG is enabled. Get rid of the 'ifdef DEBUG'
statement and use the debug macro instead.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
2013-01-16 10:52:07 +01:00
Joe Hershberger
f88e09de8d mips: serial: Fix busted manual relocation
serial_initialize() must be called after relocation to adjust the
pointers to putc(), getc(), etc.  This is busted ever since the
serial driver-model-ification series.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-12-12 13:20:24 +01:00
Daniel Schwierzeck
f0c27993e4 MIPS: constify mips_io_port_base
mips_io_port_base is exported as 'extern const unsigned long mips_io_port_base;'
in arch/mips/include/asm/io.h. Thus make the variable const too.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-12-12 13:14:16 +01:00
Daniel Schwierzeck
ea40a05422 MIPS: constify address pointer in test_bit()
Fix several warnings when enabling UBIFS on MIPS:

In file included from ubifs.h:2137:0,
                 from ubifs.c:26:
misc.h: In function 'ubifs_zn_dirty':
misc.h:38:2: warning: passing argument 2 of 'test_bit' discards 'const' qualifier from pointer target type [enabled by default]
../include/asm/bitops.h:569:23: note: expected 'volatile void *' but argument is of type 'const long unsigned int *'

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-12-08 21:48:19 +01:00
Zhi-zhou Zhang
0d69d918ab MIPS: fix a latent bug on initialize $gp
If bal is 8 bytes aligned, the _gp will not be 8 bytes aligned.
then the following ld insntrustion generates a Adel exception.
So here make _gp be always aligned in 8 bytes.

Signed-off-by: Zhi-zhou Zhang <zhizhou.zh@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-12-08 21:33:07 +01:00
Tom Rini
d41b3cc16f Merge branch 'master' of git://git.denx.de/u-boot-mips 2012-11-27 20:34:51 -07:00
Zhi-zhou Zhang
8ab36d2e54 MIPS: do not initialize timestamp variable before relocate_code
Because timestamp is declared as `static', we needn't initialize
it by writing it a zero. If we do it before relocate_code, we
will write into a flash address(0xffffffffbfc0xxxx).

Signed-off-by: Zhi-zhou Zhang <zhizhou.zh@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-11-25 21:50:43 +01:00
Ilya Yanok
c60795f41d usb: use linux/usb/ch9.h instead of usbdescriptors.h
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.

As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.

Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.

This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:06 +01:00
Marek Vasut
6c7c946cad common: Convert the U-Boot commands to LG-arrays
This patch converts the old method of creating a list of command
onto the new LG-arrays code. The old u_boot_cmd section is converted
to new u_boot_list_cmd subsection and LG-array macros used as needed.

Minor adjustments had to be made to the common code to work with the
LG-array macros, mostly the fixup_cmdtable() calls are now passed the
ll_entry_start and ll_entry_count instead of linker-generated symbols.

The command.c had to be adjusted as well so it would use the newly
introduced LG-array API instead of directly using linker-generated
symbols.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
2012-10-22 08:29:42 -07:00
Simon Glass
8dc22b00ac mips: Change global data baudrate to int
This doesn't need to be a long, so change it.

Also adjust bi_baudrate to be unsigned.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-19 15:25:45 -07:00
Tom Rini
d1ff690612 Merge branch 'master' of git://git.denx.de/u-boot-mips 2012-10-17 08:57:13 -07:00
Pavel Herrmann
4d1361d867 split AU1X00 specific code from cmd_ide.c
move special case of ide_swap_read() for AU1X00 SoC into SoC-specific directory.

Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
2012-10-17 07:59:09 -07:00
Marek Vasut
ec3fd68952 serial: Use default_serial_puts() in drivers
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
2012-10-17 07:55:50 -07:00
Zhi-zhou Zhang
32afad783e MIPS: add board qemu-mips64 support
Both big-endian and little-endian are tested with below commands:
Rom version: (Default, Now we config it as rom version)
qemu-system-mips64el -M mips -bios u-boot.bin -cpu MIPS64R2-generic -nographic
qemu-system-mips64 -M mips -bios u-boot.bin -cpu MIPS64R2-generic -nographic
Ram version:
qemu-system-mips64el -M mips -cpu MIPS64R2-generic -kernel u-boot -nographic
qemu-system-mips64 -M mips -cpu MIPS64R2-generic -kernel u-boot -nographic

Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-10-16 15:02:08 +02:00
Zhi-zhou Zhang
090854c826 MIPS: add support for 64 bit addressing
Prepare for upcoming mips64 support. This patch add mips64 address
support.

Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
[daniel.schwierzeck@gmail.com: prefer _MIPS_SZLONG in posix_types.h to fix some warnings]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2012-10-16 15:02:08 +02:00
Zhi-zhou Zhang
cb0a6a1ecc MIPS: don't use camel-case style
Replace camel-case style with upper-case style globally.

Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
2012-10-16 15:02:08 +02:00
Lucas Stach
c7e3b2b586 usb: lowlevel interface change to support multiple controllers
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.

Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2012-10-15 11:54:00 -07:00
Marek Vasut
a382725060 serial: Remove CONFIG_SERIAL_MULTI from serial drivers
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-10-15 11:53:58 -07:00
Marek Vasut
6cb3273d11 serial: mips: Implement CONFIG_SERIAL_MULTI into JZ serial driver
Implement support for CONFIG_SERIAL_MULTI into JZ serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the JZ driver. Also, add a weak implementation
of default_serial_console() returning this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-10-15 11:53:51 -07:00
Marek Vasut
0191142283 serial: mips: Implement CONFIG_SERIAL_MULTI into asc serial driver
Implement support for CONFIG_SERIAL_MULTI into asc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the asc driver. Also, add a weak implementation
of default_serial_console() returning this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-10-15 11:53:51 -07:00
Marek Vasut
7b953c5165 serial: mips: Implement CONFIG_SERIAL_MULTI into au1x00 serial driver
Implement support for CONFIG_SERIAL_MULTI into au1x00 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the au1x00 driver. Also, add a weak implementation
of default_serial_console() returning this driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-10-15 11:53:51 -07:00