Make sure the transfer descriptor is flushed
before the queue is updated so that the controller
will not see old information.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This prevents a crash if tftpboot is given a bad filename.
rx_req will be released by eth_reset_config
which is called by eth_disconnect,
which is called using the .disconnect member of usb_gadget_driver by mv_pullup in mv_udc
which is called using the .pullup member of usb_gadget_ops by usb_gadget_disconnect
which is called by usb_eth_halt
which is called using the .halt member of eth_device by eth_halt
which is called by TftpHandler when TFTP_ERR_FILE_NOT_FOUND or TFTP_ERR_ACCESS_DENIED occurs
I trigger this with the following commands
setenv ipaddr 10.0.0.2 && setenv netmask 255.255.255.0 && setenv serverip 10.0.0.1
setenv usbnet_devaddr 00:11:22:33:44:55 && setenv usbnet_hostaddr 00:aa:bb:cc:dd:ee
setenv ethprime usb_ether && setenv ethact usb_ether && setenv ncip 10.0.0.1
tftpboot 10800000 10.0.0.1:missing_file
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
set wMaxPacketSize for full speed descriptors
fs_source_desc, fs_sink_desc to 64.
Full-speed bulk endpoint can have a maximum packet size of
8, 16, 32, or 64 bytes, so choice 64.
The hs_source_desc, hs_sink_desc, already have their wMaxPacketSize
set to 512. That is the only legal value for high speed bulk endpoints.
Strictly speaking, this patch is not needed because
usb_ep_autoconfig will call ep_matches which will
override wMaxPacketSize for BULK endpoints only with
the size associated with the endpoint setup by the udc driver.
But if you want to rely on this, you may as well combine the
full speed descriptor with the high speed descriptor to
minimize confusion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add the OMAP file for the xHCI Host controller
This code will initilialize the proper components within the
OMAP5 to enable the xHCI host controller.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Add new functionality to turn on SMPS10 regulator.
This supplies the VBUS to devices connected to the
USB host ports
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This patch adds a new samsung,vbus-gpio parameter to the device tree, in
preparation of replacing the currently hardcoded VBUS GPIO mechanism in
exynos5-dt.c with a device tree controlled solution, just as it already
exists in the Linux kernel.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Some Exynos boards, such as the SMDK5250, control USB port power through
a GPIO pin. For now this had been hardcoded in the exynos5-dt board
file, but not all boards use the same pin, requiring local changes to
support different boards.
This patch moves the GPIO initialization into the USB host controller
drivers which they belong to, and uses the samsung,vbus-gpio parameter
in the device tree to configure it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This enables support for xHCI host controller on Exynos5
and further disables EHCI support, to make sure only one
host controller is enabled at a time, since right now
using two controllers at a time is not possible with
current usb core infrastructure.
Anyone who wants to enable EHCI support again needs to
enable CONFIG_USB_EHCI, CONFIG_USB_EHCI_EXYNOS once again
in exynos5-dt config.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
XHCI stack driver needs this to align buffers to
CacheLine boundary. So define the same to be '64'
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Adding device node for xhci host controller to enable
usb 3.0 on exynos5250.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Adding required compatible string for xHCI host controller
as well as USB 3.0 PHY to enable dt support for usb 3.0 on
exynos5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Adding methods to turn on/off power to USB3.0 type PHY
as and when required by the controller.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
In case the MX23/MX28 is switched into JTAG mode via the BootMode select
switches, the BootROM bypasses the CPU core registers initialization.
This in turn means that the Stack Pointer (SP) register is not set as
it is in every other mode of operation, but instead is only zeroed out.
To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure
the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out.
Note that in case the SP is already configured, we must preserve that exact
SP value and must not modify it. This is important since in every other mode
but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads
U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to
continue it's operation after returned from SPL and the system would crash.
Finally, add the JTAG mode switch identifier, so it's not recognised as
Unknown mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
This board supports FEC Ethernet, SPI NOR and NAND flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Christoph Baumann <c.baumann@ppc-ag.de>
Add basic support for mx6q udoo board.
For further information about Udoo board:
http://www.udoo.org/
Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Now that mkimage can generate an BootStream for i.MX23 and i.MX28,
use the mkimage as a default tool to generate the BootStreams instead
of the elftosb tool. This cuts out another obscure dependency.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Zynq lowlevel_init() was implemented in C but stack
pointer is setup after function call in _main().
Move architecture setup to arch_cpu_init() which is call
as the first function in board_init_f() which
already have correct stack pointer.
Reported-by: Sven Schwermer <sven.schwermer@tuhh.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The prototype of handlers had changed.
This commit uses cast with (void *) rather than
the handler-specific prototype.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add support for hsi2c controller available on exynos5420.
Note: driver currently supports only fast speed mode 100kbps
Change-Id: I02555b1dc8f4ac21c50aa5158179768563c92f43
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: R. Chandrasekar <rc.sekar@samsung.com>
At present the i2c ports are enumerated in a strange way - the
fdtdec_find_aliases_for_id() function is used, but then the ID returned
is ignored and the ports are renumbered. The effect is the same provided
that the device tree has the ports in the same order, or uses aliases,
and has no gaps, but it is not correct.
Adjust the code to use the function as intended. This will allows device
tree aliases to change the device order if required.
As a result, the i2c_busses variable is dropped. We can't be sure that
there are no 'holes' in the list of buses, so must check the whole
array.
Note: it seems that non-FDT operation is now broken in this drive and
will need to be reinstated for upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59369
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
The Exynos5 i2c driver does not handle NACKs properly. This change:
- fixes the NACK processing problem (do not continue transaction if
address cycle was NACKed)
- eliminates a fair amount of duplicate code
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
NoMMU systems have a access violation problem with i2c_reloc_fixup.
Blame for it is a double relocation of the adapter itself. The
i2c_adap_p is already relocated, if i2c_reloc_fixup is called.
This patch removes the relocation of i2c_adap_p from i2c_reloc_fixup
to fix this.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
If user uses the I2C in before the relocation, board of sh and rmobile
will not start. This will solve this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
check first, if we are on the bus, we want to enable. If so,
return immediately, do not calc max adapter number, nor check
other things.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
(Interface is not quite the same as Phillips PCA9547.)
Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
On generic board, the i2c init initialize only
one bus. But the new i2c subsystem allow to
manage severals i2c bus. So in the case, instead
of initializing a bus, we just set the current
i2c bus. The initialization will be done in
the i2c command.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
This adds the preset value to register, and setup of baudrate.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This changes clock definition of SCIF from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_SCIF_CLK_FREQ, and clock definition of TMU from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_TMU_CLK_FREQ for boards.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
The former SH/SCIF driver had calculated baudrate based on CONFIG_SYS_CLK_FREQ.
The newest SH/SCIF needs calculation of the clock for SCIF.
This patch defines clock CONFIG_SH_SCIF_CLK_FREQ for SCIF and changes it to
CONFIG_SH_SCIF_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
The former SH/TMU driver had calculated timer based on CONFIG_SYS_CLK_FREQ.
The newest SH/TMU newly needs calculation of the clock for TMU.
This patch defines clock CONFIG_SH_TMU_CLK_FREQ for TMU and changes it to
CONFIG_SH_TMU_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
A chache API of SH is developped by reference in linux kernel.
And API was the same as the linux kernel.
This patch change cache API to defines as U-Boot.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
"static u16 bit" is not necessary to use this as static global variable.
This patch fixes this.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
timer_init function sets timer prescaler bit.
The previous code so did not mask this bit, this function was to overwrite
the bit. This will fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
