* Added variables to support SPI booting
* Note that the first 512KiB are reserved for 4 copies of SPL.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
* Added support to the default environment variables for NAND
boot.
* Add nandboot to the default bootcmd.
Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Rather than load the FPGA file from the FAT partition, look
at entry in system EEPROM to decide which file to retrieve directly
from the EXT3 partition.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Also, change bootdelay to 0 but allow pressing 'S' to stop at U-Boot prompt.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard Gray <howard.gray@matrix-vision.de>
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
The IGEP COM PROTON is a new ultra compact module design with an
on-board ethernet controller.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Current '#if' directives (used in igep00x0.h config file) comparing MACH_TYPE
values in igep00x0.h doesn't work as expected. The comparision between
CONFIG_MACH_TYPE and MACH_TYPE_IGEP0020 is always true independent of the IGEP
machine configured.
For example, following directive
if (CONFIG_MACH_TYPE == MACH_TYPE_IGEP0020)
define something
endif
Is always evaluated true although we configure u-boot for MACH_TYPE_IGEP0030.
The build doesn't shows any error so looks that both defines had always the same
value. Including the mach-types.h file sets properly the value of
MACH_TYPE_IGEPxxxx.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
This adds necessary config options and a new build target,
am335x_evm_usbspl, to enable usb booting and fixes board_eth_init()
function to take into account that we may have USB ether support in SPL
now. This uses the same MAC for both cpsw and USB, in order to match
ROM behavior.
The usbspl build target does not contain UART SPL, CPSW SPL or extra
environment settings, so that we may fit within our binary size
constraint.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Signed-off-by: Tom Rini <trini@ti.com>
Remove it from the processor specific headers. This is
already defined in the common header km83xx.h.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This board is similar to TUXX1 but it has a different sized second
FPGA. Therefore the configuration for the third chipselect is different.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This is a preparation for the upcoming kmopti2 board. This board has
also a second fpga on board which is different to the tuxx1 target. But we
want to use the same header file. So remove the config option
KM_DISABLE_APP2 and simply use the board names to distinguish the features.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
If CONFIG_NAND_ECC_BCH is chosen from in the board configuration we add
an ecc mode to the kernel commandline.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Replace the hardcoded string with a variable. If CONFIG_NAND_ECC_BCH is
set we use a specific name for the uImage (ecc_bch_uImage).
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport
ethernet interface. The ethernet port used for network booting is
automatically selected by u-boot. If a Piggy is plugged, the Piggy
port is selected (UEC2, eth1). If the Piggy isn't present, the
Frontport is selected (UEC0, eth0).
The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28)
and released at startup.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Invert the polarity of this option to simplify the Makefile logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Gabe Black <gabeblack@chromium.org>
In order to use the more thorough memory test, the macro
CONFIG_SYS_MEMTEST_SCRATCH must be defined with a usable
address.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The baudrate is already defined by CONFIG_BAUDRATE and there is no need
to keep CONFIG_SYS_BAUDRATE_TABLE.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Turn on SPI in cardhu config file
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add driver for tegra SPI "SLINK" style driver. This controller is
similar to the tegra20 SPI "SFLASH" controller. The difference is
that the SLINK controller is a genernal purpose SPI controller and the
SFLASH controller is special purpose and can only talk to FLASH
devices. In addition there are potentially many instances of an SLINK
controller on tegra and only a single instance of SFLASH. Tegra20 is
currently ths only version of tegra that instantiates an SFLASH
controller.
This driver supports basic PIO mode of operation and is configurable
(CONFIG_OF_CONTROL) to be driven off devicetree bindings. Up to 4
devices per controller may be attached, although typically only a
single chip select line is exposed from tegra per controller so in
reality this is usually limited to 1.
To enable this driver, use CONFIG_TEGRA_SLINK
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for configuring tegra SPI driver from devicetree.
Support is keyed off CONFIG_OF_CONTROL. Add entry in seaboard dts
file for spi controller to describe seaboard spi.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Only add "lcd" into TEGRA_DEVICE_SETTINGS if CONFIG_VIDEO_TEGRA.
Otherwise, "lcd" is meaningless.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The libfdt.h file is the definition file for libfdt. It is unnecessary
to include other fdt header files (the necessary ones are pulled in
by libfdt.h).
Signed-off-by: Gerald Van Baren <gvb@unssw.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Roese <sr@denx.de>
trivial:
fdt_support.c:89:64: warning: Using plain integer as NULL pointer
fdt_support.c:325:65: warning: Using plain integer as NULL pointer
fdt_support.c:352:65: warning: Using plain integer as NULL pointer
For the following bad constant expression, We hardcode the max. number of
memory banks to four for the foreseeable future, and add an error with
instructions on what to do once it's exceeded:
fdt_support.c:397:22: error: bad constant expression
For the rest below, sparse found a couple of wrong endian conversions
in of_bus_default_translate() and fdt_get_base_address(), but
otherwise the rest is mostly annotation fixes:
fdt_support.c:64:24: warning: cast to restricted __be32
fdt_support.c:192:21: warning: incorrect type in assignment (different base types)
fdt_support.c:192:21: expected unsigned int [unsigned] [usertype] tmp
fdt_support.c:192:21: got restricted __be32 [usertype] <noident>
fdt_support.c:201:21: warning: incorrect type in assignment (different base types)
fdt_support.c:201:21: expected unsigned int [unsigned] [addressable] [usertype] tmp
fdt_support.c:201:21: got restricted __be32 [usertype] <noident>
fdt_support.c:304:13: warning: incorrect type in assignment (different base types)
fdt_support.c:304:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:304:13: got restricted __be32 [usertype] <noident>
fdt_support.c:333:13: warning: incorrect type in assignment (different base types)
fdt_support.c:333:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:333:13: got restricted __be32 [usertype] <noident>
fdt_support.c:359:13: warning: incorrect type in assignment (different base types)
fdt_support.c:359:13: expected unsigned int [unsigned] [usertype] val
fdt_support.c:359:13: got restricted __be32 [usertype] <noident>
fdt_support.c:373:21: warning: cast to restricted __be32
fdt_support.c:963:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:963:48: expected restricted __be32 const [usertype] *p
fdt_support.c:963:48: got unsigned int [usertype] *<noident>
fdt_support.c:971:48: warning: incorrect type in argument 1 (different base types)
fdt_support.c:971:48: expected restricted __be32 const [usertype] *p
fdt_support.c:971:48: got unsigned int [usertype] *<noident>
fdt_support.c:984:29: warning: incorrect type in argument 1 (different base types)
fdt_support.c:984:29: expected restricted __be32 const [usertype] *cell
fdt_support.c:984:29: got unsigned int [usertype] *addr
fdt_support.c:996:32: warning: incorrect type in argument 1 (different base types)
fdt_support.c:996:32: expected restricted __be32 const [usertype] *cell
fdt_support.c:996:32: got unsigned int [usertype] *addr
fdt_support.c:1041:41: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1041:41: expected restricted __be32 const [usertype] *cell
fdt_support.c:1041:41: got unsigned int [usertype] *addr
fdt_support.c:1053:41: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1053:41: expected restricted __be32 const [usertype] *range
fdt_support.c:1053:41: got unsigned int const [usertype] *[assigned] ranges
fdt_support.c:1064:53: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1064:53: expected restricted __be32 const [usertype] *addr
fdt_support.c:1064:53: got unsigned int [usertype] *addr
fdt_support.c:1110:50: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1110:50: expected restricted __be32 const [usertype] *addr
fdt_support.c:1110:50: got unsigned int *<noident>
fdt_support.c:1121:49: warning: incorrect type in argument 1 (different base types)
fdt_support.c:1121:49: expected restricted __be32 const [usertype] *cell
fdt_support.c:1121:49: got unsigned int *<noident>
fdt_support.c:1147:60: warning: incorrect type in argument 2 (different base types)
fdt_support.c:1147:60: expected restricted __be32 const [usertype] *addr
fdt_support.c:1147:60: got unsigned int *<noident>
fdt_support.c:1081:5: warning: symbol '__of_translate_address' was not declared. Should it be static?
fdt_support.c:1154:5: error: symbol 'fdt_translate_address' redeclared with different type (originally declared at include/fdt_support.h:95) - incompatible argument 3 (different base types)
fdt_support.c: In function 'fdt_node_offset_by_compat_reg':
fdt_support.c:1173:17: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
See also linux kernel commit 0131d897 "of/address: use proper
endianess in get_flags".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
commit 142419e "dtc/libfdt: sparse fixes", for u-boot's libfdt copy.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
upstream dtc commit feafcd972cb744750a65728440c99526e6199a6d
"dtc/libfdt: introduce fdt types for annotation by endian checkers".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
and, if including libfdt.h which includes libfdt_env.h in
the correct order, don't include fdt.h before libfdt.h.
this is needed to get the fdt type definitions set from
the project environment before fdt.h uses them.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Jerry Van Baren <gvb.uboot@gmail.com>
For AM335X boards, such as the EVM and Bone Linux kernel fails to
locate the device tree blob on boot. The reason being is that
u-boot is copying the DT blob to the upper part of RAM when booting
the kernel and the kernel is unable to access the blob.
By setting the fdt_high variable to 0xffffffff (to prevent the copy)
the kernel is able to locate the DT blob and boot.
This patch is tested on BeagleBone platform.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tom Rini <trini@ti.com>
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD
Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI
Not yet supported:
NAND
RTC
LCD
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
For production systems it is better to use script images since
they are protected by checksums and carry valuable information like
name and timestamp. Also, you can't validate the content passed to
env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP4 supported boards (Panda and TI SDP4430) are used
primarily for development, this patch allows U-Boot to load env var
from a text file in case that an boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Nishanth Menon <nm@ti.com>
This patch adds an GPIO LED boot status for IGEP boards.
The GPIO LED used is the red LED0 while the Linux kernel
uses the green LED0 as the boot status.
By using different GPIO LEDs, the user can know in which
step of the boot process the board currently is.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Even when the IGEPv2 board and the IGEP Computer-on-Module
are different from a form factor point of view, they are
very similar in the fact that share many components and how
they are wired.
So, it is possible (and better) to have a single board file
for both devices and just use the CONFIG_MACH_TYPE to make
a differentiation between each board when needed.
This change avoids code duplication by removing 298 lines of
code and makes future maintenance easier.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
CONFIG_ARM_DCC_MULTI should be also removed in the patch
"serial: Remove CONFIG_SERIAL_MULTI from serial drivers"
(sha1: a382725060)
Because the driver defines serial_* functions
which cause conflict with serial.c (multiple definition of serial_*)
Removing CONFIG_SERIAL_MULTI function also require to define
default_serial_console for cases where another serial driver
is not available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
As far as every arch has a get_timer function,
run_command_and_time_it code can now disappear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-By: Che-Liang Chiou <clchiou@chromium.org>
[trini: s/ulong/unsigned long/ in command.h portion]
Signed-off-by: Tom Rini <trini@ti.com>
toupper/tolower function are already declared, so use them.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This code was targetting one specific Microblaze platform
configuration which is obsolete and fsl bus isn't used
in this way.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The P2020DS build had grown too large, and video support isn't enabled
in almost any other Freescale board. Disabling it allows us to keep
building, and provides options for reenabling it later.
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9132QDS is a Freescale reference design board for BSC9132 SoC.
BSC9132 SOC is an integrated device that targets the evolving Microcell,
Picocell, and Enterprise-Femto base station market subsegments.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
BSC9132QDS Overview
--------------------
2Gbyte DDR3 (on board DDR), Dual Ranki
32Mbyte 16bit NOR flash
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
SD slot
USB-ULPI
eTSEC1: Connected to SGMII PHY
eTSEC2: Connected to SGMII PHY
PCIe
CPRI
SerDes
I2C RTC
DUART interface: supports one UARTs up to 115200 bps for console display
Apart from the above it also consists various peripherals to support DSP
functionalities.
This patch adds support for mainly Power side functionalities and peripherals
Signed-off-by: Naveen Burmi <NaveenBurmi@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
In order to be able to build a u-boot.pbl image, both the
CONFIG_PBLPBI_CONFIG and CONFIG_PBLRCW_CONFIG variables have to be
defined.
This patch sets these two files for the P2041RDB board.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.
B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
configuration reset source. The RCW source is set by appropriate
DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
- total four refclk, including CPRI clock scheme
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
USB controller in uboot is a required feature for MPC8544DS. Without this
support there is no 'usb' command in uboot.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The controller interleaving only takes the usable memory mapped to cs0. In
the case of bank interleaving not enabled, only half of dual-rank DIMM will
be used.
For single-rank DIMM bank interleaving will be auto disabled.
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Relax parameters to give address latching more time to setup.
Tighten parameters to make it overall faster.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240QDS's QIXIS FPGA has 4k register space size and IFC controller's
Address Mask Registers is initialised 64K size.
So Fix the Address Mask Register initilisation as 4K
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
"CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere
outside of config files.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The following features are supported:
* 128 MB DDR1 SDRAM
* DUART
* SD/MMC Card Socket
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Add support for the MMC attached to SSP1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
It is useful to be able to try a range of
possible phy addresses to connect.
Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h
to store the mmc partition, but in order for it to have effect we should place
it into 'mmcpart' variable.
Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds support for MX23-based Olinuxino board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Tested all 5 'buses', i2c probe enumerates device addresses on all
but dev 4 (I2C4) [no devices on that bus on my Cardhu].
Note that this uses the extant tegra_i2c.c driver w/o modification.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
include/configs/tegra-common.h now holds common config options
for Tegra SoCs.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
TEGRA_DEVICE_SETTINGS lives now in tegra-common-post.h.
This removes custom TEGRA_DEVICE_SETTINGS for all tegra boards providing
video output, except seaboard, which was fixed by Stephen already.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds LCD panel descriptions to the device tree of PAZ00 and
enables LCD support in the configuration.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The TEC ships with a 7" LCD panel that provides a resolution of 800x480
pixels. Add a corresponding panel description to the device tree and
enable LCD support in the configuration.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Medcom-Wide has a 15" LCD panel with a resolution of 1366x768
pixels. Add a corresponding panel description to the device tree and
enable LCD support in the configuration.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In commit abbab70 we added a prototype for hw_watchdog_init, in a
Freescale i.MX watchdog driver. We did not however guard it with an
__ASSEMBLY__ check and broke some platforms. Move this to the end of
the file with other prototypes and guard it.
Signed-off-by: Tom Rini <trini@ti.com>
Since commit de7d02aeb (mx6qsabresd: add usdhc2 and usdhc4 support)
SDHC3 device node is no longer 0, which breaks loading a uImage from SDHC3.
Fix it by adapting the default environment to use CONFIG_SYS_MMC_ENV_DEV as the
correct mmc node for loading the kernel from.
While at it, go back to using SDHC3 as the default mmc, since we have Yocto
images that generate an SD card containing U-boot,kernel and rootfs, so it is
more convenient to keep using SDHC3 as it was originally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
For a generic environment, we shouldn't have a fixed rootfs filesystem
so we drop it from env.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add dataflash boot support on at91sam9x5ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
We enable console multiplexing and use both serial and LCD for stdout/stderr.
Initially, u-boot output console is observed via serial port.
If you also have a DP panel connected onto your SMDK5250 board,
you can switch to LCD console by typing "setenv stdout lcd".
You can always switch back to serial using "setenv stdout serial".
You can switch error console(stderr) as well, using similar commands.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
u-boot compilation fails for smdk5250 when we deselect CONFIG_LCD
from the main config file.
Following error was observed:
drivers/video/libvideo.o: In function `exynos_lcd_init':
/home/ajay/u-boot-samsung/drivers/video/exynos_fb.c:68: undefined reference to `lcd_set_flush_dcache'
This is because exynos video drivers have dependency on CONFIG_LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
IGEP board PC16550D (ns16550) UART doesn't set the
Transmitter Empty (TEMT) Bit in SPL. This makes
U-Boot to hang while waiting for TEMT. Add the
CONFIG_SYS_NS16550_BROKEN_TEMT config option to
avoid this issue.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
When booting an IGEPv2 board from NAND with SPL, U-Boot hangs
trying to read the OMAP General Purpose Memory Controller (GPMC).
The reason is that the GPMC initialization function is called
inside spl_board_init() and this function is only executed when
CONFIG_SPL_BOARD_INIT is defined.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Some boards want to report more than just memory size. For example, it
might be useful to display the memory type (DDR2, DDR3) or manufacturer.
Add a weak function to support this requirement, accessed through a new
'meminfo' command.
Any example of the DRAM: output is below, just for illustration:
SMDK5250 # meminfo
DRAM: 2 GiB Elpida DDR3 @ 800MHz
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for SST 4KB sector granularity.
Many recent SST flashes, i.e. SST39VF3201B and similar of this family
are declared CFI-conformant from SST. They support CFI query, but implement
2 different sector sizes in the same memory: a 64KB sector (they call it
"block", std AMD erase cmd=0x30), and a 4KB sector (they call it "sector",
erase cmd=0x50). Also, CFI query on these chips, reading from address 0x2dh
of cfi query struct, detects a number of secotrs for the 4KB granularity
(flinfo shows it).
For all other aspects, they are CFI compliant, so, as Linux do, i think
it's a good idea to handle these chips in the CFI driver, with a fixup
to allow 4KB granularity, as should be expected, instead of 64KB.
Signed-off-by: Angelo Dureghello <sysamfw@gmail.com>
Signed-off-by: Stefan Rose <sr@denx.de>
Add panel_info structure required by LCD driver
and DP panel platdata for SMDK5250.
Add GPIO configuration for LCD.
Enable FIMD and DP support on SMDK5250.
DP Panel size: 2560x1600.
We use 16BPP resolution to get LCD console.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chomium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add required compatible information for PMIC
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This will fix the following error:
---8<---
UBIFS error (pid 0): ubifs_mount: Error reading superblock on volume 'ubi:root' errno=-12!
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: prafulla@marvell.com
Cc: dimax.main@gmail.com
Tested-by: Alex Xol <dimax.main@gmail.com>
Instead of using the serverip we get from the DHCP server, implicitly use
the broadcast address, which is automatically set when no ncip environment
variable is set. That way it isn't necessary to use a special DHCP
configuration to set the netconsole peer.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
These variables are only used if CONFIG_SYS_CONSOLE_IS_IN_ENV
is set. This isn't the case, so we can drop them safely.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().
Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).
Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Add required compatible information for USB
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add required compatible information for SPI driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds FDT support to the sound driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add required compatible information for sound driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Functions added to get the I2C bus number and reset I2C bus using
FDT node.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In order to mx53 ROM to properly load the U-boot image, its header size should
be multiple of 512 bytes.
This issue was observed with gcc 4.6.2/4.7.3, which caused data aborts:
U-Boot 2013.01-rc2-00172-gf8cfcf1-dirty (Dec 26 2012 - 13:13:28)
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
CPU: Freescale i.MX53 family rev2.1 at 1000 MHz
Reset cause: WDOG
Net: FEC
Warning: FEC using MAC address from net device
Hit any key to stop autoboot: 0
data abort
MAYBE you should read doc/README.arm-unaligned-accesses
pc : [<aff72220>] lr : [<aff721fc>]
sp : af565e20 ip : af566918 fp : 00000000
r10: 00000003 r9 : affabb5b r8 : af565f58
r7 : 00000000 r6 : 36747fff r5 : af5668e8 r4 : 36747fff
r3 : af5668ec r2 : af5668eb r1 : 00000000 r0 : af5668e8
Flags: NzcV IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
,and this patch fixes it.
Also, even though the ROUND macro is already defined in common.h,
the reason for redefining it in image.h is explained by Stefano Babic:
"I will remark a previous comment - even if including common.h seems a
good idea to avoid duplications, it makes tools like mkimage to depend
on the selected board, because <board>_config must run. Even if this is
not a problem for us u-boot developers, it becomes an issue when these
tools are included in distros (like u-boot-tools in Ubuntu) and cannot
be packaged."
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Looks like the original comment came from a copy and paste from mx31ads.h.
It does not have a context on mx51evk anymore, so delete it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
It makes more sense to use on-board eMMC to store environments. The
boot partition 1 is selected by default.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The on-board number of available usdhc devices is something board
specific. The patch moves CONFIG_SYS_FSL_USDHC_NUM out of
mx6qsabre_common.h and adds usdhc2 and usdhc4 support for mx6qsabresd
board.
To keep the default mmc device for environment same as before (usdhc3),
it moves CONFIG_SYS_MMC_ENV_DEV out of mx6qsabre_common.h and changes
it to 1 for mx6qsabresd.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Adjust the NAND partitioning layout so that there is a separate partition
for the ramdisk and fdt blob on the NAND.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Support for a new command (defined at envs) - spl_export generates
the ATAGS image necessary for fast boot. Afterwards, it is stored
at ext4 partition.
Generated image format:
CRC [4B] SIZE [4B] PAYLOAD(ATAGS/DT) [SIZE]
Remarks:
- CRC is calculated only for PAYLOAD
- SIZE is the size of PAYLOAD
It is important to adjust ${splsize} when large image is generated.
It is defined as hex, since ext4 related commands expect it.
The ${spladdr} environment variable corresponds to
CONFIG_SYS_SPL_ARGS_ADDR
Additionally definitions for DFU have been refactored and support for
EFI has been added as well.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since commit c733681 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) mx53loco fails to allocate the memory for PMIC:
U-Boot 2013.01-rc2-dirty (Dec 20 2012 - 15:55:01)
Board: MX53 LOCO
I2C: ready
DRAM: 1 GiB
pmic_alloc: No available memory for allocation!
pmic_init: POWER allocation error!
CPU: Freescale i.MX53 family rev2.0 at 800 MHz
Reset cause: POR
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Calling the PMIC related functions at a later stage, ie, from board_late_init()
fixes the issue.
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
For a generic environment, we shouldn't have a fixed rootfs filesystem
so we drop it from env.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add the configuration file for exynos5250 based SMDK5250 board.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Create a common configuration file for all exynos5250 based boards.
Going forward we will be using DT based driver discovery for all the boards
based on Exynos5. The different boards added will have there own config.h files
which internally will include this file and specify their specific DT files.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add the compatibility string and constant for the ethernet driver
so the device tree parsing code can recognize it.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SPL doesn't write to the environment. These list entries prevent the
functions from being garbage-collected, even though nothing will look at
the list. This caused several SPL builds (e.g. P2020RDB-PC_NAND) to
break due to size limitations and/or unresolved symbols.
A static inline function is used to provide a context in which we
can consume the callback, and thus avoid unused function warnings.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
Add support for USB host ports on cm-t3530 and cm-t3730.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
This converts MPC8313ERDB NAND boot to use the new SPL infrastructure.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* By a sequence of unfavorable conditions in the config header file, the eb_cpu5282
booting from internal stopped after relocation. Blame it is a faulty value of
CONFIG_SYS_MONITOR_BASE. This patch fix this by replace the wrong condition in
config header with option in board.cfg
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
If probe of a newly connected device fails for some reason, clean up
the allocated entry in usb_dev array.
Signed-off-by: Milind Choudhary <milindc@codeaurora.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for ethernet over USB which can be used for e.g. booting
process. It works with tftp and dhcp clients code.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
CONFIG_SYS_TFTP_LOADADDR is defined on severals boards,
but it's never used. So we can safely removed it.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
- since commit 418396e212 nand write.raw
can take the number of page to be written as an argument. nand_update_full
is passing the size (in bytes) to nand write.raw. This value was previously
ignored but now breaks the write.
- this patch updates the default environment of these boards to provide a
pagecount instead of a size to nand write.raw.
- tested on a mx28evk with a 4k page NAND and on a custom board with a
2k page NAND.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
The #ifdef here is not enough to stop part_efi.c from being built, only
being unused. And with recent changes this now leads to warnings. The
easiest solution here is to just let the garbage collection at link time
do its job.
Signed-off-by: Tom Rini <trini@ti.com>
Use the variable access flags to implement the protection for ethaddr
and serial# instead of hard-coding them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Similar to the env callback command, this will show details about the
options available, the static list, and the currently active variables.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address. Call
env_acl_validate_setenv_params() from setenv() in fw_env.c.
If the entry is not found in the env .flags, then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Need to build in _ctype for isdigit for Linux.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address.
If the entry is not found in the env ".flags", then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The silent variable now updates the global data flag anytime it is
changed as well as after the env relocation (in case its value is
different from the default env in such cases as NAND env)
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for per-variable callbacks to the "hashtable" functions.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!!fix comment in callback
When printing all variables with env print, don't print variables that
begin with '.'. If env print is called with a '-a' switch, then
include variables that begin with '.' (just like the ls command).
Variables printed explicitly will be printed even without the -a.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Move the read of the old value to inside the check function. In some
cases it can be avoided all together and at the least the code is only
called from one place.
Also name the function and the callback to more clearly describe what
it does.
Pass the ENTRY instead of just the name for direct access to the whole
data structure.
Pass an enum to the callback that specifies the operation being approved.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use a flag in hsearch_r for insert mode passed from import to allow the
behavior be different based on use.
Now that "do_check" is called for all imports, ensure console init is
complete before updating the console on relocation import
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
isspace() and strim() are not in the typical user-mode string.h, so
put them in a separate compilation unit so that they can be built into
tools that need them independent of the other common string functions.
This allows code shared by u-boot and the linux user-mode tools to link.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Enable support for GPT partition table restoration at Samsung's Trats
development board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
The restoration of GPT table (both primary and secondary) is now possible.
Function 'gpt_restore' presents example of partition restoration process.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Custom definitions of le_XX_to_int functions have been replaced with
standard ones, defined at <compiler.h>
Replacement of several GPT related structures members with ones
indicating its endianness and proper size.
Signed-off-by: Chang Hyun Park <heartinpiece@outlook.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This move is necessary to export gpt header and GPT partition entries to be
used with other commands or subsystems.
Additionally the part_efi.h file has been cleaned-up to supress checkpatch's
warnings.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The ustrtoul shall convert string defined size (e.g. 1GiB) to unsigned
long type (as its name implies).
Up till now it had returned int, which might cause problems with large
numbers (GiB range), when interpreted as U2 signed numbers.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This implements a library for accessing EDID data from an LCD panel.
This is used to obtain information about the panel such as its
resolution and type.
This is a tidied-up version of the original code pulled from
https://github.com/ynezz/u-boot-edid.
The changes we made are:
- removed bit fields in the struct;
- removed endianness cases in the struct;
- fixed some wrong definitions;
- fixed to fit 80 columns;
- fixed some code styles.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This new command supports hashing SHA1 and SHA256. It could be extended
to others such as MD5 and the CRC algorithms. The syntax is modeled on
those:
hash <algorithm> <address> <length> [*<dest_addr> | <dest_envvar>]
to calculate a hash, and:
hash -v <algorithm> <address> <length> [*<verify_addr> | <verify_envvar>]
to verify a hash.
Use CONFIG_CMD_HASH to enable the command, CONFIG_SHA1 to enable SHA1 and
CONFIG_SHA256 to enable SHA256.
The existing sha1sum command remains.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a SHA1 command and want to add a SHA256 command also. Instead of
duplicating the code, create a generic hash API which can process
commands for different algorithms.
Signed-off-by: Simon Glass <sjg@chromium.org>
strncasecmp() is present as strnicmp() but disabled. Make it available
and define strcasecmp() also. There is a only a small performance penalty
to having strcasecmp() call strncasecmp(), so do this instead of a
standalone function, to save code space.
Update the prototype in arch-specific headers as needed to avoid warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for making the hash function common, we may as well use
const where we can.
Also add a watchdog version of the hashing function.
Signed-off-by: Simon Glass <sjg@chromium.org>
In preparation for making the hash function common, we may as well use
const where we can. Also the input length cannot be negative, but may
be very large, so use unsigned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes data is on a block device and within a partition, but not in a
particular filesystem.
This commands permits reading raw data from a partition.
Signed-off-by: Kenneth Waters <kwaters@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Gettime returns the current timer value. If CONFIG_SYS_HZ is defined
then the timer value is also converted to seconds.
Tegra20 (SeaBoard) # gettime
Timer val: 7754
Seconds : 7
Remainder : 754
sys_hz = 1000
There has been some discussion about whether this is useful enough to
be included in U-Boot. The following boards do not have CONFIG_SYS_HZ
defined:
M52277EVB
M52277EVB_stmicro
M53017EVB
M54418TWR
M54418TWR_nand_mii
M54418TWR_nand_rmii
M54418TWR_nand_rmii_lowfreq
M54418TWR_serial_mii
M54418TWR_serial_rmii
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Make the necessary adaptions for the new PMIC framework, so that mx25pdk can
be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Moved the pmic_max77686.c max77686_pmic.h to drivers/power
and made required changes accordingly
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We handle i2c_write return code and complain in case of error. We propagate the
error, too, to allow better handling at the upper level in the future.
Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Conflicts:
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/woodburn_common.h
board/woodburn/woodburn.c
These boards still use the old old PMIC framework, so they
do not merge properly after the power framework was merged into
mainline.
Fix all conflicts and update woodburn to use Power Framework.
Signed-off-by: Stefano Babic <sbabic@denx.de>
