The sysreset uclass unconditionally provides a definition of the
reset_cpu() function. So does the sunxi board code. Fix the build with
SYSRESET enabled by omitting the function from the board code in that
case. The code still needs to be kept around for use in SPL.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The more recent Allwinner SoCs BootROMs can actually load SPL images
larger than 32KB. We use this on the H616 to fit the extra code needed
for the PMIC into the image, and have provisions in board.c to respect
that larger SPL size when booting from MMC.
However the sunxi SPL SPI loader has a hardcoded load offset of 32KB,
which will fail on the H616.
To fix this, use the same algorithm we use for MMC: if the SPL size is
smaller than 32KB, we use 32KB, otherwise we expect the U-Boot payload
directly after the SPL code.
This prepares for SPI booting with larger SPLs like on the H616.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Now that the last users of legacy I2C (outside of SPL) have been
resolved, we can enable DM_I2C at the sunxi architecture level.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pmic_bus functions are used in both SPL (for regulator setup) and
U-Boot proper (for regulator setup, SID access, GPIO, and poweroff).
Currently, pmic_bus conflicts with DM_I2C because it uses the legacy I2C
interface. This commit makes pmic_bus dual-compatible with either the
legacy I2C functions or the newly-added PMIC_AXP driver (which uses
DM_I2C). In turn, this allows platforms to start transitioning to DM_I2C
in U-Boot proper, without breaking boards that still depend on the
legacy I2C interface for other reasons.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Instead of using the SoC symbols to decide the bus type, use whichever
bus driver is actually enabled. This allows collapsing all of the AXP2xx
and AXP8xx variants into one "else" case. It also has the advantage of
falling back to I2C when the other bus drivers are disabled; this works
because all of the PMICs support I2C in addition to other interfaces.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the rsb functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants, so move that to the common header.
There are only a couple of pairs of hardware/runtime addresses used
across all PMIC variants. So far the code expected only the "primary"
pair, but some PMICs like the AXP305 and AXP805 use the secondary pair,
so add support for that to the DM driver as well.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This bus controller is used to communicate with an X-Powers AXP PMIC.
Currently, various drivers access PMIC registers through a platform-
specific non-DM "pmic_bus" interface, which depends on the legacy I2C
framework. In order to convert those drivers to use DM_PMIC, this bus
needs a DM_I2C driver.
Refactor the p2wi functions to take the base address as a parameter,
and implement both the existing interface (which is still needed in
SPL) and the DM_I2C interface on top of them.
The register for switching between I2C/P2WI/RSB mode is the same across
all PMIC variants. Move that to the common header, so it can be used by
both interface implementations.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
AXP_PMIC_BUS enables communication with a specific AXP PMIC at a
PMIC-dependent I2C/P2WI/RSB bus address. It is automatically selected
as a dependency of the PMIC driver. It should not be selectable by the
user when no PMIC is chosen.
AXP_GPIO uses the pmic_bus functions, and also depends on a specific
PMIC header to pick up register definitions.
Both of these changes have no impact on any existing configs, since
the code does not compile if the dependencies are not met.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
SUN8I_RSB should not be selected by MACH_SUN8I, because the hardware
is not present in half of those SoCs (H3/H5, R40, and V3s). Move the
selection to the SoCs where the hardware actually exists.
As it currently stands, selecting that option also requires using it in
some way, which is not the case for one A80 board. Since we have only
three A80 boards in total, we select it their via their defconfigs.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixing up Sunchip_CX-A99 build]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
CONFIG_SPL_I2C is the wrong symbol to use here. It is the top-level
Kconfig symbol (not specific to either legacy or DM I2C), whereas the
i2c_init() function is specific to legacy I2C. This change fixes a
build failure when enabling SPL_I2C but not SPL_SYS_I2C_LEGACY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.
This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
All SoCs since the Allwinner A64 (H5, H6, R40, H616) feature the so
called "new timing mode", so enable this in Kconfig for those SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.
Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.
As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most clock factors and dividers in the H6 PLLs use a "+1 encoding",
which we were missing on two occasions.
This fixes the MMC clock setup on the H6, which could be slightly off due
to the wrong parent frequency:
mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000
Also the CPU frequency (PLL1) was a tad too high before.
For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code
itself, not in the bit field macro. Move this there to be aligned with
what the other SoCs and other PLLs do.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Currently sunxi Makefile manually specifies full path to dw-hdmi common
code. However, that is not needed because it can be selected in Kconfig
instead.
Select proper symbol in Kconfig and drop path from Makefile.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we do not have proper dual rank memory detection on R40
(because we omitted PIR_QSGATE, which does not work on R40 with our
configuration), and dual rank memory is just simply disabled as early
R40 boards available (Banana Pi M2 Ultra and Berry) have single rank
memory.
As a board with dual rank memory (Forlinx OKA40i-C) is now known to us,
we need to have a way to do memory rank detection to support that board.
Add some routine to detect memory rank by trying to access the memory
in rank 1 and check for error status of the memory controller, and then
enable dual rank memory on R40.
Similar routine can be used to detect half DQ width (which is also
detected by PIR_QSGATE on other SoCs), but it's left unimplemented
because there's no known R40 board with half DQ width now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: Move R40 detect code call into sunxi_dram_init()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we have known that R40 has a configuration register for its
rank 1, which allows different configuration than rank 0. Reverse
engineering of newest libdram of A64 from Allwinner shows that A64 has
this register too. It's bit 0 (which enables dual rank in rank 0
configuration register) means a dedicated rank size setup is used for
rank 1.
Now, Pine64 scheduled to use a 3GiB LPDDR3 DRAM chip (which has 2GiB
rank 0 and 1GiB rank 1) on PinePhone, that makes asymmetric dual rank
DRAM support necessary.
Add this support. The code could support both A64 and R40, but because
dual rank detection is broken on R40 now, we cannot really use it on R40
currently.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYEE0zg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXMQWAJ4pwG2oykEwa+BEC5JUrJ9B/QWa+wCeP1HwJS5N
siPaX+vgDLOqTg1Y/T4=
=0Dow
-----END PGP SIGNATURE-----
Merge tag 'next-2021-03-04' of https://gitlab.denx.de/u-boot/custodians/u-boot-video into next
- convert sunxi_display to DM_VIDEO
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).
Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The A23, A33, H3, H5, A83T, V3 and Sochip S3 sun8i SoCs can mux uart1 on
GPIOs PG6 and PG7. This patch adds support for using uart1 on those pins
as boot console.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there is a magic bit in PRCM region which seemingly
makes PLLs work if it's enabled. Sadly, there is no documentation what
it does exactly, so we'll just mimick BSP boot0 behaviour and enable it
before any clock is set up.
Fixes: b18bd53d6c ("sunxi: introduce support for H616 clocks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is used for debug terminal on all known H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 has mostly the same clocks as H6 with some small differences. Just
reuse H6 clocks for H616 and handle differences with macros.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
I2C support, especially R_I2C port, will be needed in future. Upcoming
support for H616 will need R_I2C to adjust DRAM voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.
Add a config option to fix it up so it can function properly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that in rare cases, current analytical approach to detect
correct DRAM bus width and rank on H6 doesn't work. On some TV boxes
with DDR3, incorrect DRAM configuration triggers write leveling error
which immediately stops initialization process. Exact reason why this
error appears isn't known. However, if correct configuration is used,
initalization works without problem.
In order to fix this issue, simply try another configuration when any
kind of error appears during initialization, not just those related to
rank and bus width.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Thomas Graichen <thomas.graichen@googlemail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner V3/Sochip S3 uses the same die with Allwinner V3s/S3L, but V3 comes
with no co-packaged DDR (DDR3 is usually used externally), and S3L comes
with co-packaged DDR3.
Add support for Allwinner V3/S3 chips by add SoC names to original V3s
choice, and allow to select DDR3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Previously, because we have no source code about the DRAM initialization
of V3s and missing some configurations (delays and MBUS QoS info), our
V3s DRAM initialization sequence is hacked from the H3 one.
As the SDK shipped with PineCube contains source code for V3s libdram,
we can retrieve these information from it and tweak some other magic
bits.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
When compiling with CONFIG_SPL_SERIAL=n, gcc warns about
mbus_configure_port not being marked as static:
In file included from include/common.h:34,
from arch/arm/mach-sunxi/dram_sunxi_dw.c:11:
include/log.h:185:4: warning: 'printf' is static but used in inline function 'mbus_configure_port' which is not static
185 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
include/log.h:192:2: note: in expansion of macro 'debug_cond'
192 | debug_cond(_DEBUG, fmt, ##args)
| ^~~~~~~~~~
arch/arm/mach-sunxi/dram_sunxi_dw.c💯2: note: in expansion of macro 'debug'
100 | debug("MBUS port %d cfg0 %08x cfg1 %08x\n", port, cfg0, cfg1);
| ^~~~~
Fix this by updating the function accordingly.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
