Commit graph

5365 commits

Author SHA1 Message Date
Alexander Dahl
72d5e3c140 ARM: dts: at91: sam9x60-curiosity: Sync LED nodes from Linux
Copied as is from Linux Kernel release v6.4.

(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)

Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-29 17:39:01 +03:00
Mihai Sain
87d1cac49d board: at91: sama5d29_curiosity: add initial support for sama5d29_curiosity
Add initial support for sama5d29_curiosity board.

Hardware:
SoC: SAMA5D29 500 MHz
DRAM: LPDDR2 512 MiB
PMIC: MCP16502
Debug: UART0
Flash: QSPI NOR 8 MiB
RGB LCD connector
Mikrobus connectors x 2
SD-Card connectors x 2
USB 2.0 x 2

Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
2023-08-07 11:42:16 +03:00
Alexander Dahl
4d7a5593f6 ARM: dts: at91: sam9x60-curiosity: Add raw NAND flash
Basically the same as on sam9x60-ek.  Same as in Linux.  NAND flash is
correctly detected when booting into U-Boot:

    U-Boot 2023.07-rc6-00005-g12719f75dc-dirty (Jul 05 2023 - 13:06:35 +0000)

    CPU:   SAM9X60 128MiB DDR2 SiP
    Crystal frequency:       24 MHz
    CPU clock        :      600 MHz
    Master clock     :      200 MHz

    Model: Microchip SAM9X60 Curiosity
    DRAM:  128 MiB
    Core:  145 devices, 22 uclasses, devicetree: separate
    NAND:  512 MiB
    MMC:   sdhci-host@80000000: 0, sdhci-host@90000000: 1
    Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
    In:    serial
    Out:   serial
    Err:   serial
    Net:   eth0: ethernet@f802c000
    Hit any key to stop autoboot:  0

Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-02 08:54:21 +03:00
Alexander Dahl
08c46fef31 ARM: dts: at91: sam9x60-curiosity: Improve alignment with upstream
- nodes moved
- using node references by label instead of dulicating the node tree

Makes it easier to compare with the dts file from Linux kernel.

Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-02 08:54:21 +03:00
Alexander Dahl
cdbd40dbb5 ARM: dts: at91: sam9x60: Change i2c compatible
There's a more specific compatible string for the i2c interface, use it.

Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-02 08:54:21 +03:00
Alexander Dahl
19891288e3 ARM: dts: at91: sam9x60-curiosity: Fix EEPROM type
The user guide says it's a Microchip 24AA025E48 serial EEPROM, which is
a 2-Kbit I2C Serial EEPROM with EUI-48™ Identity.  This is the chip
actually populated on board EV40E67A rev 4.

Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-02 08:54:21 +03:00
Alexander Dahl
a2283b301c ARM: dts: at91: sam9x60: Better align with upstream dtsi
No functional changes, but this:

- reorder nodes (ordered by memory offset as in Linux)
- add label to pinctrl node name for easier reference in board files
- fix whitespace

Diff to sam9x60.dtsi in Linux is much better readable now.

Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-02 08:54:21 +03:00
Tom Rini
aaeaef2536 Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- i2c-gpio: Correctly handle new {sda, scl}-gpios bindings (Chris)
- mvebu: x240: Use i2c-gpio instead of built in controller (Chris)
2023-08-01 10:17:23 -04:00
Jonas Karlman
1f54f71b18 board: rockchip: Add Radxa E25 Carrier Board
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.

Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA

Device tree is imported from linux next-20230728.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
2023-07-31 20:34:32 +08:00
Jagan Teki
b71f74eab4 arm64: dts: rockchip: Drop unused rk3328-xhci node
rk3328-xhci has been added due to the fact that the upstream
dwc3 is unsupported. Moreover, the driver for rk3328-xhci is
not added to the code tree.

By considering these facts and unsupported rk3328-xhci this
patch is dropping all related code from DT. However, the DWC3
is fixed now in dwc3-generic and RK3328 USB 3.0 is functional
in upcoming patches.

Let's drop it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 20:33:18 +08:00
Chris Packham
5c1c6b7306 arm: mvebu: x240: Use i2c-gpio instead of built in controller
There is an Errata with the built-in I2C controller where various I2C
hardware errors cause a complete lockup of the CPU (which eventually
results in an watchdog reset).

Put the I2C MPP pins into GPIO mode and use the i2c-gpio driver instead.
This uses a bit-banged implementation of an I2C controller and avoids
triggering the Errata.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2023-07-31 13:50:57 +02:00
Eugen Hristev
b8fc65473a board: rockchip: add Radxa ROCK5A Rk3588 board
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.

There are tree variants depending on the DRAM size : 4G, 8G and 16G.

Specifications:

     Rockchip Rk3588S SoC
     4x ARM Cortex-A76, 4x ARM Cortex-A55
     4/8/16GB memory LPDDR4x
     Mali G610MC4 GPU
     MIPI CSI 2 multiple lanes connector
     4-lane MIPI DSI connector
     Audio – 3.5mm earphone jack
     eMMC module connector
     uSD slot (up to 128GB)
     2x USB 2.0, 2x USB 3.0
     2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
     Gigabit Ethernet RJ45 with optional PoE support
     40-pin IO header including UART, SPI, I2C and 5V DC power in
     USB PD over USB Type-C
     Size: 85mm x 56mm (Raspberry Pi 4 form factor)

Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")

Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Eugen Hristev
7031224000 ARM: dts: rockchip: rk3588: Move bootph-all props to common file
Move bootph-all prop to common SoC dt file, because they are typically used
by multiple boards.
Unreferenced nodes are removed from the SPL device tree during a
normal build.

Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
def50c66cc rockchip: rk3568-rock-3a: Fix pcie2x1 and pcie3x2 pinctrl override
The pcie pinctrl override added in the commit a76aa6ffa6 ("rockchip:
rk3568-rock-3a: Enable PCIe and NVMe support") is causing a pinmux issue
on linux when using a EFI boot flow.

The pcie reset-gpios must however be configured with gpio function, or
the device will freeze running pci enum and nothing is connected.

Adjust the pinctrl override in u-boot.dtsi to fix this issue. PCIe/NVMe
continues to work in both U-Boot and linux after this change.

Also revert disable of sdmmc2 and uart1 to fix use of wifi in linux when
using a EFI boot flow.

Fixes: a76aa6ffa6 ("rockchip: rk3568-rock-3a: Enable PCIe and NVMe support")
Fixes: 073d911ae6 ("rockchip: rk3568-rock-3a: Sync device tree from linux")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
2023-07-31 17:34:43 +08:00
Jonas Karlman
747f9f2663 rockchip: rk3588-rock-5b: Fix SPI Flash alias
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") enabled SPI flash support by adding a spi0 alias.

Correct this by adding spi0-spi5 aliases in rk3588s-u-boot.dtsi and
SF_DEFAULT_BUS=5 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.

Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
52f6b96d27 rockchip: rk3568-rock-3a: Fix SPI Flash alias
The commit 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI
NOR flash") enabled SPI flash support by overriding the spi0 alias.

Correct this by adding a new spi4 alias in rk356x-u-boot.dtsi and
SF_DEFAULT_BUS=4 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.

Fixes: 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
ee75f16868 rockchip: rk3399-roc-pc: Fix SPL max size and SPI flash payload offset
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB

Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.

Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
263f81d3a5 rockchip: rk3399-pinephone-pro: Fix SPL max size and SPI flash payload offset
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB

Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.

Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
cc11d5c4ba rockchip: rk3399-pinebook-pro: Fix SPL max size and SPI flash payload offset
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB

Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.

Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
ada6328738 rockchip: rk3399-rockpro64: Fix SPL max size and SPI flash payload offset
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB

Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.

Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.

Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
f40dcc7d1e rockchip: rk356x-u-boot: Use relaxed u-boot,spl-boot-order
BootRom will try to load TPL+SPL from media in the following order:
- SPI NOR Flash
- SPI NAND Flash
- NAND Flash
- eMMC
- SDMMC

SPL will try to load FIT from media in the order defined in the device
tree u-boot,spl-boot-order property.

Change the default order to load FIT from to:
- same media as TPL+SPL
- SDMMC
- eMMC

Boards with strict load order requirements should override the
u-boot,spl-boot-order property in the board specific u-boot.dtsi.

Fixes: 42f67fb51c ("rockchip: rk3568: Fix boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
a3ef37a08d rockchip: rk356x-u-boot: Add bootph-all to common pinctrl nodes
Add bootph-all prop to common pinctrl nodes for eMMC, FSPI, SD-card and
UART2 that are typically used by multiple boards. Unreferenced nodes are
removed from the SPL device tree during a normal build.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
23ad80a360 rockchip: rk3566-radxa-cm3-io: Sync dts from linux v6.4
Sync rk3566-radxa-cm3-io.dts from linux v6.4.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:42 +08:00
Jonas Karlman
0e3480c1f7 rockchip: rk356x: Sync dtsi from linux v6.4
Sync rk356x.dtsi from linux v6.4.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:42 +08:00
Jonas Karlman
6855fa625c board: rockchip: Add Pine64 SOQuartz on CM4-IO
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:36 +08:00
Jonas Karlman
d0026e5908 board: rockchip: Add Pine64 SOQuartz on Blade
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
651492bfb2 board: rockchip: Add Pine64 SOQuartz on Model A
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
f52452bbea board: rockchip: Add Pine64 Quartz64-B Board
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.

Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
9c1b5d163e board: rockchip: Add Pine64 Quartz64-A Board
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
bec51f3fb3 Revert "arm: dts: rockchip: radxa-cm3-io, rock-3a: enable regulators for usb"
Remove regulator-boot-on prop from regulators now that the phy core has
support for phy-supply after the commit c57e0dcd93 ("phy: add support
for phy-supply").

This reverts commit 7911f409ff.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:40:38 +08:00
Alper Nebi Yasak
42cb8f0112 rockchip: chromebook_speedy: Enable sound
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:40:13 +08:00
Alper Nebi Yasak
b73b6558a1 rockchip: veyron: Unify u-boot.dtsi bootph-all fragments
The rk3288-veyron-speedy-u-boot.dtsi file duplicates the bootphase dts
fragments from rk3288-veyron-u-boot.dtsi even though it #inclues that.
Deduplicate these into the latter file, which should also make the eMMC
available to the other veyron boards' SPL.

Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:40:13 +08:00
Pegorer Massimo
ffd41939fe rockchip: rk3308: fix same-as-spl boot order
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.

Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.

Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:38:59 +08:00
Pegorer Massimo
1d7e1d09ca rockchip: rk3308: add support for sdmmc boot
Some ROCK Pi S SKU/models are not equipped with SD-NAND (eMMC),
therefore SPL needs access to sdmmc: add it to rk3308-u-boot.dtsi
with bootph-all property.

Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:38:55 +08:00
Tom Rini
6544943819 Merge branch '2023-07-27-TI-K2-K3-updates'
- Resync some of the K3 DTS files with the kernel, and pull in some
  required related updates to keep drivers in sync with the dts files
  now.  Bring in some incremental fixes on top of one of the series I
  applied recently as well as updating the iot2050 platform.  Also do a
  few small updates to the K2 platforms.
2023-07-28 10:25:50 -04:00
Jan Kiszka
badaa1f6a7 boards: siemens: iot2050: Unify PG1 and PG2/M.2 configurations again
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.

Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2023-07-28 10:11:01 -04:00
Nishanth Menon
7937af120b arm: dts: k3-am62: Bump dtsi from linux v6.5-rc1
Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
  either the definitions from main.dtsi OR duplication from u-boot.dtsi

Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
2023-07-28 10:10:57 -04:00
Jonas Karlman
94da929b93 board: rockchip: Add Hardkernel ODROID-M1
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.

Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host

Device tree is imported from linux v6.4.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Jonas Karlman
062b712999 rockchip: rk356x: Update PCIe config, IO and memory regions
Update config, IO and memory regions used based on [1] with pcie3x2
config reg address and reg size corrected.

Before this change:

  PCI Autoconfig: Bus Memory region: [0-3eefffff],
  PCI Autoconfig: Bus I/O region: [3ef00000-3effffff],

After this change:

  PCI Autoconfig: Bus Memory region: [40000000-7fffffff],
  PCI Autoconfig: Bus I/O region: [f0100000-f01fffff],

[1] https://lore.kernel.org/lkml/20221112114125.1637543-2-aholmes@omnom.net/

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Jonas Karlman
a76aa6ffa6 rockchip: rk3568-rock-3a: Enable PCIe and NVMe support
Add missing pinctrl and defconfig options to enable PCIe and NVMe
support on Radxa ROCK 3 Model A.

Use of pcie20m1_pins and pcie30x2m1_pins ensure IO mux selection M1.
The following pcie_reset_h and pcie3x2_reset_h ensure GPIO func is
restored to the perstn pin, a workaround to avoid having to define
a new rockchip,pins.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Christopher Obbard
0022461ba6 arm: rockchip: Add Radxa ROCK 4SE
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.

Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")

Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Christopher Obbard
1379c7cfc9 arm: rockchip: sync ROCK Pi 4 SoCs from Linux
To prepare for ROCK 4 SE support, changes are needed to the common ROCK
Pi 4 devicetree to move the OPP from the common devicetree to individual
board devicetrees. Sync the Rockchip RK3399 ROCK Pi 4-related DTs from
Linux to gain from these changes.

Kernel tag: next-20230719
Kernel commits:
cfa12c32b96f ("arm64: dts: rockchip: correct wifi interrupt flag in Rock \
Pi 4B")
cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
2bd1d2dd808c ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+")
fd2762a62646 ("arm64: dts: rockchip: Move OPP table from ROCK Pi 4 dtsi")

Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Alex Bee
fff7f5e978 rockchip: Support OP-TEE for ARM in FIT images created by binman
CONFIG_SPL_OPTEE_IMAGE option is used during DRAM size detection for
Rockchip ARM platform to indicate that an OP-TEE binary was already loaded
and a Trusted Execution Environment (TEE) is available in order to
block/reserve a memory-region for it.

This adds a bunch of new `#if's` to u-boot-rockchip.dtsi to include the
OP-TEE binary in the FIT image for ARM SOCs if CONFIG_SPL_OPTEE_IMAGE is
selected.
That makes it a little harder to read, but I opted for that, because all
the duplicates in an extra ARM-OP-TEE-specfic .dtsi would be the greater
evil, IMHO. Besides it's more likley being "forgotten" to sync when changes
in u-boot-rockchip.dtsi are made.

The no longer required rockchip-optee.dtsi and it's inclusions are dropped.

The hardcoded load address is common across all OP-TEE implemenations for
Rockchip (vendor and upstream).

The OP-TEE-binary is non-optional if CONFIG_SPL_OPTEE_IMAGE is selected and
there will be an error if the file does not exist and/or `TEE=` build
option is missing.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Jagan Teki
0a3a5746c3 board: rockchip: Add Edgeble Neural Compute Module 6B
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.

Add support for this SoM and IO board.

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Jagan Teki
fcf5a3c900 arm64: dts: rockchip: Add rk3588 Edgeble Neu6B
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.

General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT

Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.

General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion

Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.

Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Jagan Teki
51c82dda77 ARM: dts: rockchip: Add rk3588j-u-boot.dtsi
Add rk3588j-u-boot.dtsi for adding U-Boot specific nodes and
properties for Rockchip RK3588J SoC.

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Jagan Teki
0a086cb6eb arm64: dts: rockchip: Add Rockchip RK3588J
Rockchip RK3588J is the industrial-grade version of RK3588 SoC and
is operated with -40 °C to +85 °C temparature.

Add rk3588j specific dtsi for adding rk3588j specific operating points
and other changes to be add in future.

Kernel commit:
commit <8274a04ff1dc> ("arm64: dts: rockchip: Add Rockchip RK3588J")

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
6a73211d4b rockchip: rk3568: Add support for FriendlyARM NanoPi R5C
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.

Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V

The device tree is taken from kernel v6.4-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
0ef326b5e9 rockchip: rk3568: Add support for FriendlyARM NanoPi R5S
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.

Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector

The device tree is taken from kernel v6.4-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
9bd954ab8a rockchip: rk3328: Add support for Orange Pi R1 Plus LTS
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.

The device tree is taken from kernel v6.4-rc1.

Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00