This patch fixes a few issues noticed, when testing this new driver on
ARM Octeon TX2 again. Here the details:
- Remove "common.h" header inclusion
- Use correct THP define on Octeon TX2
- Octeon TX2 uses the same compatible as Octeon TX. We can't distinguish
both platforms this way. Remove the unused "cavium,thunder2-99xx-twsi"
compatible and add a check to the Octeon TX2 specific
"cavium,thunderx-i2c" so that the correct driver data is selected.
- Removed "struct pci_device_id" definition and U_BOOT_PCI_DEVICE()
as its not needed for the PCI based probing on Octeon TX2
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the description of devfdt_get_addr_ptr, this function should
return NULL on failure, but currently it returns (void *)FDT_ADDR_T_NONE.
Fix this by making devfdt_get_addr_ptr return NULL on failure, as
described in the function comments. Also, update the drivers currently
checking (void *)FDT_ADDR_T_NONE to check for NULL.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- i2c/nx_i2c.c: Some adaptions mainly because of changes in
"struct udevice".
- several Bugfixes in nx_i2c.c.
- the driver has been for s5p6818 only. Code extended appropriately
in order s5p4418 is also working.
- "probe_chip" added.
- pinctrl-driver/dt is used instead of configuring the i2c I/O-pins
in the i2c-driver.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
- Bug fixes and updates on ls2088a,ls1028a, ls1046a, ls1043a, ls1012a
- lx2-watchdog support
- layerscape: pci-endpoint support, spin table relocation fixes and
cleanups
- fsl-crypto: RNG support and bug fixes
Move i2c_early_init_f to common function
to initialize baudrate of i2c
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the _ptr suffixed variant instead of casting. Also, convert it to
dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE.
One curious part is an error check like follows in
drivers/watchdog/omap_wdt.c:
priv->regs = (struct wd_timer *)devfdt_get_addr(dev);
if (!priv->regs)
return -EINVAL;
devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error.
So, this code does not catch any error in DT parsing.
dev_read_addr_ptr() returns NULL on error, so this error check
will work.
I generated this commit by the following command:
$ find . -name .git -prune -o -name '*.[ch]' -type f -print | \
xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/'
I manually fixed drivers/usb/host/ehci-mx6.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Update the PCI driver to generate ACPI information so that Linux has the
full information about each I2C bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
[bmeng: Correct one typo in dw_i2c_gen_speed_config() comments]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add a few of these calls to make it easier to see where an error occurs,
if CONFIG_LOG_ERROR_RETURN is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add debugging for a few more values and also use log to show return values
when something goes wrong. This makes it easier to see the root cause.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For many device types it is possible to figure out the name just by
looking at its uclass or parent. Add a function to handle this, since it
allows us to cover the vast majority of cases automatically.
However it is sometimes impossible to figure out an ACPI name for a device
just by looking at its uclass. For example a touch device may have a
vendor-specific name. Add a new "acpi,name" property to allow a custom
name to be created.
With this new feature we can drop the get_name() methods in the sandbox
I2C and SPI drivers. They were only added for testing purposes. Update the
tests to use the new values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to write a GPIO descriptor to the generated ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
Read SYSCFG bindings to set Fast Mode Plus bits if Fast Mode Plus
speed is selected.
Handle the stm32mp15 specific compatible to handle FastMode+
registers handling which is different on the stm32mp15 compared
to the stm32f7 or stm32h7.
Indeed, on the stm32mp15, the FastMode+ set and clear registers
are separated while on the other platforms (F7 or H7) the control
is done in a unique register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a new compatible "st,stm32mp15-i2c" introduced in Linux kernel v5.8
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Current driver calls the devfdt_get_addr to get the base address
of lpi2c controller in each sub-functions. Since the devfdt_get_addr
accesses the DTB and translate the address, it introduces much
overhead.
Improve the codes to use private variable which has recorded the
base address from probe.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When compiling with -Wtype-limits we see this error:
drivers/i2c/i2c-uclass.c: In function ‘i2c_deblock_gpio_loop’:
drivers/i2c/i2c-uclass.c:517:21: error: comparison of
unsigned expression >= 0 is always true [-Werror=type-limits]
517 | while (scl_count-- >= 0) {
|
Don't loop forever.
Fixes: 1f746a2c82 ("i2c: Make deblock delay and SCL clock configurable")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If the device doesn't return a version that means the device is
non-functional.
The dw_i2c_regs had invalid offsets for the version field. I got the
correct value from the DesignWare databook. It also matches what the
Picasso PPR says.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Tested on chromebook_coral:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we still have pre-driver-model code in this driver and it makes
things a bit confusing. In particular calc_bus_speed() is called with priv
as NULL if not using driver model.
This results in spk_cnt and comp_param1 being read from an invalid address
if not using driver model. For comp_param1 this may not cause problems if
reading from addresses close to 0 happens to be allowed, as high speed is
only supported by DM code. But spk_cnt is subsequently used to calculate
the bus periods and so this may cause problems (e.g. on spear600 board
which has not been migrated yet).
Add a new parameter regs parameter to calc_bus_speed() and add more
comments to this function and to _dw_i2c_set_bus_speed(), which calls it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add fuse check for I2C. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This adds the PCA9546 4-channel i2c bus switch.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fix some errors pointed out by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Do not limit to 3 (100KHz, 400KHz, 1MHz) bus frequencies, but
instead allow for any frequency. Depending on the requested
frequency (via the clock-frequency DT entry), use the spec
data from either Standard, Fast or Fast Plus mode.
In order to do so, the driver do not use anymore spec identifier
by directly handle the requested frequency and from it retrieve
the corresponding spec data to be used for the computation
of the timing register.
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove 'has_high_speed' config since we can check high speed support
from IC_COMP_PARAM_1 register.
Signed-off-by: Jun Chen <ptchentw@gmail.com>
Signed-off-by: Jun Chen <jun.chen@vatics.com>
To read IC_COMP_PARAM_1[3:2] to check is high speed possible,
and fall back to fast mode if not.
Signed-off-by: Jun Chen <ptchentw@gmail.com>
Signed-off-by: Jun Chen <jun.chen@vatics.com>
This adds support for clock stretching to the i2c-gpio driver. This is
accomplished by switching the GPIO used for the SCL line to an input
when it should be driven high, and polling on the SCL line value until
it goes high (indicating that the I2C slave is no longer pulling it
low).
This is enabled by default; for gpios which cannot be configured as
inputs, the i2c-gpio,scl-output-only property can be used to fall back
to the previous behavior.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch reworks i2c-gpio to make it easier to switch out the
implementation of the sda/scl get/set functions. This is in preparation
for a patch to conditionally implement clock stretching support.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add deblock dequence for the I2C bus, needed on some devices. This sequence
is issued once, when probing the driver, and is controlled by DT property,
"i2c-gpio,deblock".
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Export the i2c_deblock_gpio_loop() so it can be used in other places in
U-Boot. In particular, this is useful in the GPIO I2C driver, which claims
the SDA/SCL GPIOs and thus prevents the i2c_deblock() implementation from
claiming the pins as GPIOs again.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make the delay between SCL line changes and the number of SCL clock
changes configurable as a parameter of the deblock function. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Unfortunately a recent change adjusted the order of the checks here such
that 400MHz now shows up as fast-plus speed (1Mbps). Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: d96440d1e3 ("i2c: designware_i2c: Add support for fast-plus speed")
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
Now that we have uclass_first_device_drvdata(), use it from the I2C driver
to reduce code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This adds DM_FLAG_PRE_RELOC flag to probe i2c driver
before relocation
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move some of the code currently in the ofdata_to_platdata() method to
probe() so that it is not executed when generating ACPI tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to be able to calculate the speed separately from actually setting
the speed, so we can generate the required ACPI tables. Split out the
calculation into its own function.
Drop the double underscore on __dw_i2c_set_bus_speed while we are here.
That is reserved for compiler internals.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is used to store the speed information for a bus. We want to provide
this to ACPI so that it can tell the kernel. Move this struct to the
header file so it can be accessed by the ACPI i2c implementation being
added later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert the obvious uses of i2c bus speeds to use the enum.
Use livetree access for code changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update this driver to use the new standard enums for speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update this driver to use the new standard enums for speed.
Note: This driver needs to move to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update this driver to use the new standard enums for speed.
Note: This driver needs to move to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some versions of this peripheral include a spike-suppression phase of the
bus. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present the driver can end up with timing parameters which are slightly
faster than those expected. It is possible to optimise the parameters to
get the best possible result.
Create a new function to handle the timing calculation. This uses a table
of defaults for each speed mode rather than writing it in code.
The function works by calculating the 'period' of each bit on the bus in
terms of the input clock to the controller (IC_CLK). It makes sure that
the constraints are met and that the different components of that period
add up correctly.
This code was taken from coreboot which has ended up with this same
driver, but now in a much-different form.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Create a struct to hold the three timing parameters. This will make it
easier to move these calculations into a separate function in a later
patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Instead of passing this parameter into __dw_i2c_set_bus_speed(), pass in
the driver's private data, from which the function can obtain that
information. This allows the function to have access to the full state of
the driver.
Signed-off-by: Sicomp_param1mon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2c controller defines a few timing properties. Read these in and
store them for use by the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present the driver uses an approximation for the bus clock, e.g. 166MHz
instead of 166 2/3 MHz.
This can result in small errors in the resulting I2C speed, perhaps 0.5%
or so.
Adjust the existing code to start from the accurate figure, even if later
rounding reduces this accuracy.
Update the bus speed code to work in KHz instead of MHz, which removes
most of the error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Group these #defines into an enum to make it easier to understand the
relationship between them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some SoCs support a higher speed than what is currently called 'max' in
this driver. Rename it to 'high' speed, which is the official name of the
3.4MHz speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
We use struct clk here so really should include this header file to avoid
build errors. Also switch the order of clk.h in the C file to match the
required code style.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If a different input clock is required then the correct way to do this is
with a clock driver. Don't allow boards to override IC_CLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some versions of this peripherals provide more control of the bus
behaviour. Add definitions for these registers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
Some devices (2 wire eeproms for example) use some bits from the chip
address to represent the high bits of the offset instead of or as well
as using multiple bytes for the offset, effectively stealing chip
addresses on the bus.
Add a chip offset mask that can be set for any i2c chip which gets
filled with the offset overflow during offset setup.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For Apollo Lake we need to take the I2C bus controller out of reset before
using this. Add this functionality to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow this driver to set up an IO address in SPL using an 'early-regs'
property. This allows SPL to use the I2C driver without having to enable
the full PCI stack.
Also split out ofdata_to_platdata in designware driver since this is more
correct, and more convenient for the new logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drivers are not allowed to use static data since they may be used in SPL
where BSS is not available.
It is possible that driver model may provide support for numbering devices
in the future. But for now, move this to global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is hacked into the driver at present. It seems better to have it as
a separate driver that uses the base driver. Create a new file and put
the X86 code into it.
Actually the Baytrail settings should really come from the device tree.
Note that 'has_max_speed' is added as well. This is currently always false
but since only Baytrail provides the config, it does not affect operation
for other devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This fixes an issue that would cause I2C writes to timeout when the
number of bytes is a multiple of the FIFO depth (i.e. 16 bytes).
Within the transfer loop, after writing the data register with a new
byte to transfer, if the transfer size equals the FIFO depth, the loop
pauses until the INTERRUPT_COMP bit asserts to indicate data has been
sent. This same check is performed after the loop as well to ensure data
has been transferred prior to returning.
In the case where the amount of data to be written is a multiple of the
FIFO depth, the transfer loop would wait for the INTERRUPT_COMP bit to
assert after writing the final byte, and then wait for this bit to
assert once more. However, since the transfer has finished at this
point, no new data has been written to the data register, and hence
INTERRUPT_COMP will never assert.
Fix this by only waiting for INTERRUPT_COMP in the transfer loop if
there's still data to be written.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
That's not correct and it breaks SMBUS-style reads and and writes for
some chips (e.g. SYR82X/SYR83X).
Stop bit should be sent only after the last message.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When CONFIG_CLK enabled, use CLK UCLASS for clk related settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
hs: removed hunk in mxc_i2c_probe() as not longer in code
i2c_idle_bus is already used in i2c_init_transfer. So before each transfer
if the bus is not ready, the i2c_idle_bus will be used to force idle.
It is unnecessary to call it again in probe.
We found a issue when enabling i2c mux with the mxc_i2c. The mxc_i2c is probed
after mux probing. However, at this moment the mux is still in idle state not
select any port. So if we call i2c_idle_bus in probe, it will fail and cause
mxc_i2c probe failed.
Signed-off-by: Ye Li <ye.li@nxp.com>
When requesting GPIO, the GPIOD_IS_OUT is missed in flag, so the GPIO
is set the input mode not output and cause mux not work.
Signed-off-by: Ye Li <ye.li@nxp.com>
I2C dm mode enablemenet causes below compilation errors:
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
In file included from include/config.h:8:0,
from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
# error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
^~~~~
board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
i2c_early_init_f();
^~~~~~~~~~~~~~~~
arch_early_init_r
drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
ret = enable_i2c_clk(1, bus->seq);
^~~~~~~~~~~~~~
enable_irq_wake
So fix these compilation errors.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
There are no more users of the compatibility layer for i2c. Remove the
driver and all references to it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
K3 devices have I2C IP that is same as OMAP2+ family. Allow driver to be
compiled for ARCH_K3.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch solves the following warnings:
drivers/i2c/stm32f7_i2c.c: In function 'stm32_i2c_compute_solutions':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (scldel < scldel_min)
^
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (((sdadel >= sdadel_min) &&
^~
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
(sdadel <= sdadel_max)) &&
^~
drivers/i2c/stm32f7_i2c.c: In function 'stm32_i2c_choose_solution':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (clk_error < clk_error_prev) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Prior to starting a new transfer, conditionally wait for bus to not
be busy.
Reinitialise controller as otherwise operation is not stable.
For reference, see linux kernel
commit 9656eeebf3f1 ("i2c: Revert i2c: xiic: Do not reset controller before every transfer")
hs: Fixed DOS line endings
added missing '\n'
Fixed git commit description style
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Comparison should be against the actual message length, not loop index.
len is used for stopping while loop, pos is position in message.
stop should be sent when entire message is sent, not when
len and pos meet.
hs: fixed DOS line endings
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Get clock rate from clock DM if CONFIG_CLK is enabled.
Otherwise, uses IC_CLK define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Before calling __dw_i2c_set_bus_speed(),
the I2C could already be set as ether enable or disable,
we should restore the original setting instead of enable i2c anyway.
This patch fix a bug happened in init function:
__dw_i2c_init(){
/* Disable i2c */
...
__dw_i2c_set_bus_speed(i2c_base, NULL, speed);
writel(slaveaddr, &i2c_base->ic_sar);
/* Enable i2c */
}
In this case, enable i2c inside __dw_i2c_set_bus_speed() function
will cause ic_sar write fail.
Signed-off-by: Jun Chen <ptchentw@gmail.com>
This avoids useless loops inside the I2C timing algorithm.
Actually, we support only one possible solution per prescaler value.
So after finding a solution with a prescaler, the algorithm can
switch directly to the next prescaler value.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
It conforms with Reference Manual I2C timing section.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since the IHS I2C driver want upstream, the surrounding infrastructure
has changed quite a bit (notably, the fpgamap driver was replaced with a
regmap driver).
Update the driver to work with these changes.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
These options only apply when not using DM_I2C. When using device
trees, the dt will enable and control the speeds of the I2C
controller(s) and these configuration options have no effect.
So disable them in DM_I2C mode. Otherwise they show up as decoys, and
make it look like one is enabling I2C controllers and setting the speed
when really it's doing nothing.
However, a system using a SPL build will not use DM_I2C in the SPL, even
if DM_I2C is enabled for the main u-boot. And so the SPL might use the
kconfig based I2C speed controls while the main u-boot does not.
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
This is an old driver that supports both device mapped and non-mapped
mode, and covers a wide range of hardware. It's hard to change without
risking breaking something. I have to tried to be exceedingly detailed
in this patch, so please excuse the length of the commit essay that
follows.
In device mapped mode the I2C xfer function does not handle plain read,
and some other, transfers correctly.
What it can't handle are transactions that:
Start with a read, or,
Have a write followed by a read, or,
Have more than one read in a row.
The common I2C/SMBUS read register and write register transactions
always start with a write, followed by a write or a read, and then end.
These work, so the bug is not apparent for most I2C slaves that only use
these common xfer forms.
The existing xfer loop initializes by sending the chip address in write
mode after it deals with bus arbitration and master setup. When
processing each message, if the next message will be a read, it sends a
repeated start followed by the chip address in read mode after the
current message.
Obviously, this does not work if the first message is a read, as the
chip is always addressed in write mode initially by i2c_init_transfer().
A write following a read does not work because the repeated start is
only sent when the next message is a read. There is no logic to send it
when the current message is a read and next is write. It should be sent
every time the bus changes direction.
The ability to use a plain read was added to this driver in
commit 2feec4eafd ("imx: mxc_i2c: tweak the i2c transfer method"),
but this applied only the non-DM code path.
This patch fixes the DM code path. The xfer function will call
i2c_init_transfer() with an alen of -1 to avoid sending the chip
address. The same way the non-DM code achieves this. The xfer
function's message loop will send the address and mode before each
message if the bus changes direction, and on the first message.
When reading data, the master hardware is one byte ahead of what we
receive. I.e., reading a byte from the data register returns a byte
*already received* by the master, and causes the master to start the RX
of the *next* byte. Therefor, before we read the final byte of a
message, we must tell the master what to do next. I add a "last" flag
to i2c_read_data() to tell it if the message is to be followed by a stop
or a repeated start. When last == true it acts exactly as before.
The non-DM code can only create an xfer where the read, if any, is the
final message of the xfer. And so the only callsite of i2c_read_data()
in the non-DM code has the "last" parameter as true. Therefore, this
change has no effect on the non-DM code. As all other changes are in
the DM xfer function, which is not even compiled in non-DM code, I am
confident that this patch has no effect on boards not using I2C_DM.
This greatly reduces the range of hardware that could be affected.
For DM boards, I have verified every transaction the "i2c" command can
create on a scope and they are all exactly as they are supposed to be.
I also tested write->read->write, which isn't possible with the i2c
command, and it works as well. I didn't fix multiple reads in a row, as
it's a lot more invasive and obviously no one has every wanted them
since they've never worked. It didn't seem like the extra complexity
was justified to support something no one uses.
Cc: Nandor Han <nandor.han@ge.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
It is not very clear how these work in relation to the exact I2C xfers
they produce. In paticular, the address length is somewhat overloaded
in the read method. Clearly document the existing behavior. Maybe this
will help the next person who needs to work on this driver and not break
non-DM boards.
Cc: Nandor Han <nandor.han@ge.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
The twsi_wait function reads the control register for interrupt flag,
and if interrupt flag is present, it immediately reads status register.
On our device this sometimes causes bad value being read from status
register, as if the value was not yet updated.
My theory is that the controller does approximately this:
1. sets interrupt flag in control register,
2. sets the value of status register,
3. causes an interrupt
In U-Boot we do not use interrupts, so I think that it is possible that
sometimes the status register in the twsi_wait function is read between
points 1 and 2.
The bug does not appear if I add a small delay before reading status
register.
Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using this driver on socfpga gen5 with DM_I2C enabled leads to a data abort
as the 'i2c' reset property cannot be found (the gen5 dtsi does not provide
reset-names).
The actual bug was to check 'if (&priv->reset_ctl)', which is never false.
While at it, convert the driver to use 'reset_get_bulk' instead of looking
at a specific named reset and also make it release the reset on driver
remove before starting the OS.
Fixes: 622597dee4 ("i2c: designware: add reset ctrl to driver")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The chip_desc.enable field is used only for muxes, not for switches.
Document it and remove the unused values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
The Kconfig help has not been updated while adding PCA9547 and PCA9646.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
The 'u-boot,i2c-transaction-bytes' device tree property provides
information regarding number of bytes transferred by a device in a
single transaction.
This change is necessary to avoid hanging devices after soft reset.
One notable example is communication with MC34708 device:
1. Reset when communicating with MC34708 via I2C.
2. The u-boot (after reboot -f) tries to setup the I2C and then calls
force_idle_bus. In the same time MC34708 still has some data to be sent
(as it transfers data in 24 bits chunks).
3. The force_idle_bus() is not able to make the bus idle as 8 SCL
clocks may be not enough to have the full transmission.
4. We end up with I2C inconsistency with MC34708.
This PMIC device requires 24+ SCL cycles to make finish any pending I2C
transmission.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.
backport from linux:
931b18e92cd0 ("2c: meson: add configurable divider factors")
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch fixes below warnings found with checker tool.
The variable len in i2c_msg struct is of unsigned type
and it is received as recv_count which is unsigned type
but it is checked with < 0 which is always false, hence
removed it.
The local variable curr_recv_count is declared as signed
type and compared aginst unsigned recv_count which is
incorrect. This is fixed by declaring it as unsigned type.
drivers/i2c/i2c-cdns.c: In function ‘cdns_i2c_read_data’:
drivers/i2c/i2c-cdns.c:317:18: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
if ((recv_count < 0))
^
drivers/i2c/i2c-cdns.c:340:24: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
updatetx = recv_count > curr_recv_count;
^
drivers/i2c/i2c-cdns.c:361:39: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
while (readl(®s->transfer_size) !=
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cosmetic change. Any call to the recover function would need to do the
same check afterwards, so it's sensible to make it part of the function.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
It needs to be done for both reads and writes, so do it at rcar_i2c_xfer
to avoid duplication.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fix rcar_i2c_xfer return value, previously it was always returning
-EREMOTEIO when dealing with errors from calls to the read/write
functions.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Do the reset before clearing the MSR, otherwise it may result in a read
or write operation instead if the start condition is repeated.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Document the meaning of macros related to registers and values to be
written to them.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Setting up the delay only needs to be done once; move it to
rcar_i2c_set_speed so it's done at initialization time.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds support for handling arbitration lost
in case of multi master mode. When an arbitration lost
is detected, it retries for 10 times before failing.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The arbitration lost interrupt was not getting cleared
while clearing interrupts. This patch fixes this by adding
arbitration lost interrupt as well during clear. This patch
also removes hardcoded value and defined a macro for it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for R-Car Gen3 SoCs into the driver, which encompases
the Gen3 SoC extra timing register handling and 64bit build fixes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Read ICSR only once to avoid missing interrupts. This happens on R8A7791
Porter during reset, when reading the PMIC register 0x13, which may fail
sometimes because of the missed DTE interrupt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Migrate SYS_I2C_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present this driver does not check whether it is able to actually
communicate with the I2C controller. It prints a timeout message but still
considers the probe to be successful.
To fix this, add some checking that the init succeeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This driver is replaced by drivers/i2c/i2c-cdns.c DM based driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Heiko Schocher <hs@denx.de>
For !DM case busses are listed as
ZynqMP> i2c bus
Bus 0: zynq_0
Bus 1: zynq_0->PCA9544A@0x75:0
Bus 2: zynq_0->PCA9544A@0x75:1
Bus 3: zynq_0->PCA9544A@0x75:2
Bus 4: zynq_1
Bus 5: zynq_1->PCA9548@0x74:0
Bus 6: zynq_1->PCA9548@0x74:1
Bus 7: zynq_1->PCA9548@0x74:2
Bus 8: zynq_1->PCA9548@0x74:3
Bus 9: zynq_1->PCA9548@0x74:4
Bus 10: zynq_1->PCA9548@0x75:0
Bus 11: zynq_1->PCA9548@0x75:1
Bus 12: zynq_1->PCA9548@0x75:2
Bus 13: zynq_1->PCA9548@0x75:3
Bus 14: zynq_1->PCA9548@0x75:4
Bus 15: zynq_1->PCA9548@0x75:5
Bus 16: zynq_1->PCA9548@0x75:6
Bus 17: zynq_1->PCA9548@0x75:7
where is exactly describing i2c bus topology.
By moving to DM case i2c mux buses are using names from DT and because
i2c-muxes describing sub busses with the same names like i2c@0, etc it
is hard to identify which bus is where.
Linux is adding topology information to i2c-mux busses to identify them
better.
This patch is doing the same and composing bus name with topology
information.
When patch is applied with topology information on zcu102-revA.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@ff020000->i2c-mux@75->i2c@0
Bus 3: i2c@ff020000->i2c-mux@75->i2c@1
Bus 4: i2c@ff020000->i2c-mux@75->i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@ff030000->i2c-mux@74->i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@ff030000->i2c-mux@74->i2c@1
Bus 7: i2c@ff030000->i2c-mux@74->i2c@2
Bus 8: i2c@ff030000->i2c-mux@74->i2c@3
Bus 9: i2c@ff030000->i2c-mux@74->i2c@4
Bus 10: i2c@ff030000->i2c-mux@75->i2c@0
Bus 11: i2c@ff030000->i2c-mux@75->i2c@1
Bus 12: i2c@ff030000->i2c-mux@75->i2c@2
Bus 13: i2c@ff030000->i2c-mux@75->i2c@3
Bus 14: i2c@ff030000->i2c-mux@75->i2c@4
Bus 15: i2c@ff030000->i2c-mux@75->i2c@5
Bus 16: i2c@ff030000->i2c-mux@75->i2c@6
Bus 17: i2c@ff030000->i2c-mux@75->i2c@7
Behavior before the patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
For i2c controllers which are missing alias in DT there is no req_seq
setup. This function is setting up proper ID based on highest found
alias ID.
On zcu102 this is the behavior when patch is applied.
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 2: i2c@0
Bus 3: i2c@1
Bus 4: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus 5: i2c@0 (active 5)
54: eeprom@54, offset len 1, flags 0
Bus 6: i2c@1
Bus 7: i2c@2
Bus 8: i2c@3
Bus 9: i2c@4
Bus 10: i2c@0
Bus 11: i2c@1
Bus 12: i2c@2
Bus 13: i2c@3
Bus 14: i2c@4
Bus 15: i2c@5
Bus 16: i2c@6
Bus 17: i2c@7
Before this patch applied (controllers have -1 ID)
ZynqMP> i2c bus
Bus 0: i2c@ff020000
20: gpio@20, offset len 1, flags 0
21: gpio@21, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus 1: i2c@ff030000 (active 1)
74: i2c-mux@74, offset len 1, flags 0
75: i2c-mux@75, offset len 1, flags 0
Bus -1: i2c@0 (active 0)
54: eeprom@54, offset len 1, flags 0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@0
Bus -1: i2c@1
Bus -1: i2c@2
Bus -1: i2c@3
Bus -1: i2c@4
Bus -1: i2c@5
Bus -1: i2c@6
Bus -1: i2c@7
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There is a need to find out the first free i2c ID which can be used for
i2s buses (including i2c buses connected to i2c mux). Do it early in
init and share this variable with other i2c classes for uniq bus
identification.
add from hs:
fix build problem in i2c-uclass.c for omap devices
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update cadence i2c driver to support livetree
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Updates i2c muxes drivers to support livetree.
Similar changes were done by:
"net: zynq_gem: convert to use livetree"
(sha1: 26026e695a)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is needed to properly calculate i2c bus speed divisors.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Wojciech Tatarski <wtatarski@antmicro.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Xilinx AXI I2C controller driver based on the Linux i2c-xiic driver.
This driver is stripped of all the IRQ handling and uses pure polling,
yet tries to retain most of the structure of the Linux driver to make
backporting of fixes easy.
Note that the IP has a known limitation on 255 bytes read and write,
according to xilinx this is still being worked on [1].
[1] https://forums.xilinx.com/t5/Embedded-Processor-System-Design/AXI-IIC-V2-0-I2C-Master-Reading-multiple-bytes-from-I2C-slave/m-p/854419/highlight/true#M39387
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Commit f32a8007ef ("dm: i2c: Make i2c_get_chip_for_busnum() fail if the
chip is not detected") introduced a regression for the NVIDIA Jetson TX2.
For some reason the xfer callback of the tegra i2c driver doesn't support
probing the I2C devices with a 0-length message.
Fixing the regression by providing a dummy implementation of probe_chip()
that does nothing.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This allows the driver to be used without OF_CONTROL.
AM335x support DM_SPL but does not use SPL_OF_CONTROL. Enabling DM_I2C in
SPL thus requires that the omap I2C can be passed platdata.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move away from SoC specific headers to handle different register layout.
Instead use driver data to get appropriate register layouts like in the
kernel. While at it, perform some mostly cosmetic alignment/cleanup in
the functions being updated.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
i2c_get_chip_for_busnum() really should check the presence of the chip on
the bus. Most of the users of this function assume that this is done.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Sandbox i2c works using emulation drivers which are currently children of
the i2c device:
rtc_0: rtc@43 {
reg = <0x43>;
compatible = "sandbox-rtc";
emul {
compatible = "sandbox,i2c-rtc";
};
};
In this case the emulation device is attached to i2c bus on address 0x43
and provides the Real-Time-Clock (RTC) functionality.
However this is not ideal, since every device on an I2C bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
A better approach seems to be to add a separate node on the bus, an
'emulation parent'. This can be given a bogus address (such as 0xff) and
hides all the emulators away. Then we can use a phandle to point from the
device to the correct emualtor, and only on sandbox. The code to find an
emulator does not interfere with normal i2c operation.
Add a new UCLASS_I2C_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. This will be used in a
follow-on patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change static array to const when it is useful to save memory
(move stm32f7_setup=0x18 from .data to .rodata section)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
accidentially while fixing merge errors for patch:
https://lists.denx.de/pipermail/u-boot/2018-September/342278.html
missed to add files:
MAINTAINERS
drivers/i2c/Kconfig
drivers/i2c/Makefile
add them with this patch.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
The Arm Versatile Express I2C controller is a simple register-based
controller that uses a register to control the state of the SCL and
SDA lines. Add support for it.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in May 2017, in
commit eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
Replaced misspelled words "parition"/"paritioning" (missing 't') in two
Kconfig files by correct words "partition"/"partitioning"
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add the PCA9646 support, which is 2-wire bus switch and buffered 4-channel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
rk3066 and rk3188 has two I2C controller implementations.
Current I2C driver wan't work with legacy implementation.
Switching between controllers is performed using a bit inside
GFR_SOC_CON1 register. The bit setting is performed by pinctrl
driver. The patch ask pinctrl to do settings.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fix warnings by including the rk3228 variant in the compatible-list]:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When doing "i2c dev 4; i2c probe" with ENET daughter card connected
on iMX8QXP MEK board, we met a i2c bus busy issue, that the BBF of
lpi2c always show busy, but the master is idle, and stop is detected
(SDF set).
This patch addes a handling to re-init the lpi2c master for this
case. Then the issue can be worked around.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In xfer function, both bus_i2c_read and bus_i2c_write will
send a STOP command. This causes a problem when reading register
data from i2c device.
Generally two operations comprise the register data reading:
1. Write the register address to i2c device.
START | chip_addr | W | ACK | register_addr | ACK |
2. Read the Data from i2c device.
START | chip_addr | R | ACK | DATA | NACK | STOP
The STOP command should happen at the end of the transfer, otherwise
we will always get data from register address 0
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For LPI2C IP, NACK is detected by the rising edge of the ninth clock.
In current uboot driver, once NACK is detected, it will reset and then
disable LPI2C master. As a result, we can never see the falling edge
of the ninth clock.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Equivalent code that disables the hidden i2c0 slave already exists in
the Turris Omnia platform specific code. But this hidden i2c0 slave that
interferes the i2c bus is not board specific. Armada 38x SoCs and at
least some Kirkwood variants are affected as well. Add code to disable
this slave to the i2c bus driver to make it work on all affected
hardware.
Use the bind callback because we want this to always run at boot,
regardless of whether U-Boot uses the i2c bus.
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Last user of this driver went away in May 2017 in commit
eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD").
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add derivative of the rcar_i2c driver which is capable of
probing itself from DM and uses DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove the rcar_i2c driver, since it's no longer used by any
board and will be superseded by a DM and DT capable variant.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add code to look for a reset manager property. Specifically, look for the
reset-names of 'i2c'. A reset property is an optional feature, so only print
out a warning and do not fail if a reset property is not present.
If a reset property is discovered, then use it to deassert, thus bringing the
IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add an option to get the clock speed from the device tree, hence adding
compatibility with DM clock drivers.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since bus translations are now fully supported, use a plain
"dev_read_addr" to get the device address from the device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The fpgamap interface has been switched to a "single function + data
size" interface. Reflect this change in the IHS I2C driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The commit implement a gpio-based software deblocking. The code
extract I2C pins description from device tree, switch pins to GPIO
mode, toggle SCL until slave release SDA, send I2C stop and switch
I2C pins back to I2C mode.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
commit 907208c452 ("powerpc: Partialy restore core of mpc8xx")
didn't bring back support for I2C on the mpc8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
NXP layerscape platforms like ls1088a, ls2088a
uses MXC I2C Controller.
-Remove dependency of MX6 for the same.
Update related configs to use Kconfig file.
-Add SYS_I2C_MXC_I2C1,_I2C2,_I2C3,_I2C4 in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SPEED,_I2C2_,_I2C3_,_I2C4_ in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SLAVE,_I2C2_,_I2C3_,_I2C4_ in Kconfig
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Kmalloc is using memalign allocation function. It is not necessary to
align this structure so to save bytes, we move to calloc.
And kmalloc function can't be used in SPL early stage (in board_init_f())
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.
Also, Dirk's address was wrong in one place; fix that as well.
Signed-off-by: Mario Six <six@gdsys.cc>
This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and
CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Previous patch for this driver breaks i2c initialization.
commit 8bcf12ccce ("i2c: mvtwsi.c: Avoid NULL dereference")
If actual_speed is passed as NULL in this function:
static void __twsi_i2c_init(struct mvtwsi_registers *twsi, int speed,
int slaveadd, uint *actual_speed)
than __twsi_i2c_set_bus_speed never get called. This causes i2c clock
to run on default speed - 2MHz (measured with oscilloscope). This is issue
on some boards, sunxi for example, since on I2C0 bus PMU is connected.
The bootlogs with and without the patch are as follows:
Wihtout the patch:
U-Boot SPL 2018.03-rc2 (Feb 13 2018 - 09:23:17 +0200)
DRAM: 1024 MiB
Failed to set core voltage! Can't set CPU frequency
Trying to boot from FEL
U-Boot 2018.03-rc2 (Feb 13 2018 - 09:23:17 +0200) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-OLinuXino-LIME2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
With the patch:
U-Boot SPL 2018.03-rc2-00001-g838ff85 (Feb 13 2018 - 09:24:34 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from FEL
U-Boot 2018.03-rc2-00001-g838ff85 (Feb 13 2018 - 09:24:34 +0200) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-OLinuXino-LIME2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The IIC on Gen2 is compatible with this driver as well, allow it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
For '#ifndef CONFIG_DM_I2C' twsi_i2c_init() passes NULL as
4th parameter to __twsi_i2c_init().
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Make the ihs_i2c driver DM-compatible; for legacy boards, the old functions are
retained within #ifdefs.
No board uses the new DM driver yet; this patch only lays the foundation for
future support.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Prepare the function interface of the ihs_i2c driver for DM conversion
in a future patch.
While we're at it, fix some style violations, and make the code more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>