Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The 64-bit mvebu SoCs don't have a suitable timer driver so add a !ARM64
condition to the select.
Fixes: 7b530bb19e ("arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add QSPI NAND device node to the Microchip PolarFire SoC
Icicle kit device tree.
The Winbond NAND flash memory can be connected to the
Icicle Kit by using the Mikroe Flash 5 click board and
the Pi 3 Click shield.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In the v2022.10 Icicle reference design, the seg registers have been
changed, resulting in a required change to the memory map.
A small 4MB reservation is made at the end of 32-bit DDR to provide some
memory for the HSS to use, so that it can cache its payload between
reboots of a specific context.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_SYS_MIPS_TIMER_REQ
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Resolve all uses of CONFIG_SYS_MHZ with the currently defined value.
Remove code which depends on CONFIG_SYS_MHZ but where no board configs
actually use that code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the needed bus mappings for the two main RTI memory ranges and
the required device tree nodes in the main domain.
Same as kernel commit 6dd8457dc20693e2ba9054c171499b22664fd4e7
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
So far the Calxeda machines were using the CONFIG_SYS_TIMER_* macros to
simply hardcode the address of the counter register of the SP804 timer.
This method is deprecated and scheduled for removal.
Use the newly introduced SP804 DM_TIMER driver to provide timer
functionality on Highbank and Midway machines. The base address and base
frequency are taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently our semihosting trap function is somewhat fragile: we rely
on the current compiler behaviour to assign the second inline assembly
argument to the next free register (r1/x1), which happens to be the
"addr" argument to the smh_trap() function (per the calling convention).
I guess this is also the reason for the noinline attribute.
Make it explicit what we want: the "addr" argument needs to go into r1,
so we add another register variable. This allows to drop the "noinline"
attribute, so now the compiler beautifully inlines just the trap
instruction directly into the calling function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit f4b540e25c5c("arm: smh: Fix uninitialized parameters with newer
GCCs") added a memory clobber to the semihosting inline assembly trap
calls, to avoid too eager GCC optimisation: when passing a pointer, newer
compilers couldn't be bothered to actually fill in the structure that it
pointed to, as this data would seemingly never be used (at least from the
compiler's point of view).
But instead of the memory clobber we need to tell the compiler that we are
passing an *array* instead of some generic pointer, this forces the
compiler to actually populate the data structure.
This involves some rather hideous cast, which is best hidden in a macro.
But regardless of that, we actually need the memory clobber, but for two
different reasons: explain them in comments.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARM semihosting interface uses different trap instructions for
different architectures and instruction sets. So far we were using
AArch64 and ARMv7-M, and had an untested v7-A entry. The latter does
not work when building for Thumb, as can be verified by using
qemu_arm_defconfig, then enabling SEMIHOSTING and SYS_THUMB_BUILD:
==========
{standard input}:35: Error: invalid swi expression
{standard input}:35: Error: value of 1193046 too large for field of 2 bytes at 0
==========
Fix this by providing the recommended instruction[1] for Thumb, and
using the ARM instruction only when not building for Thumb. This also
removes some comment, as QEMU for ARM allows to now test this case.
Also use the opportunity to clean up the inline assembly, and just define
the actual trap instruction inside #ifdef's, to improve readability.
[1] https://developer.arm.com/documentation/dui0471/g/Semihosting/The-semihosting-interface?lang=en
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add test cases for accessing the FWU Metadata on the sandbox
platform. The sandbox platform also uses the metadata access driver
for GPT partitioned block devices.
The FWU feature will be tested on the sandbox64 variant with a raw
capsule. Remove the FIT capsule testing from sandbox64 defconfig --
the FIT capsule test will be run on the sandbox_flattree variant.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The FWU metadata structure is accessed through the driver model
interface. On the stm32mp157c dk2 and ev1 boards, the FWU metadata is
stored on the uSD card. Add the fwu-mdata node on the u-boot specifc
dtsi file for accessing the metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Use binman to build an image which includes all the U-Boot phases so that
a full VBE boot can take place with just that image.bin file. Attach the
image file to mmc2 so it can be loaded.
VBE is used to load images in two phases:
- In VPL, VBE decides which SPL image to load
- In SPL, VBE decides which U-Boot image to load
The latter should really be determined by VPL, since it does the full
signature verification on the selected configuration. However, we have
separate configurations for SPL and U-Boot proper, so for now we keep it
simple and have SPL do its own verification. This will need to be
tidied up later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the sandbox executable is assumed to be arg[0] but this only
works for a single jump (e.g. from SPL to U-Boot). Add a new arg to solve
this issue, along with a detailed comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports jumping to a file, to get to the next
U-Boot phase. We want to support other methods, so update the code to
use an enum for the method. Also use the
Use board_boot_order() to set the order, so we can add more options.
Also add the MMC methods into the BOOT_DEVICE enum so that booting
from MMC can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
This happens every time sandbox moves to the next phase so is not very
interesting. Display the message only when debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
As STI timer is renamed to ARM A9 global timer, change BCM63138 to use
the new global timer config symbol name.
This patch applies on top of the my previous patch [1].
[1]: https://lists.denx.de/pipermail/u-boot/2022-August/491060.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
This is actually a panel, not a video device. Rename the option, move it
into the right place and make it depend on PANEL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently sandbox configuration defautls to 64bit and there is no
automation for building 32bit sandbox on 32bit hosts.
Use _LP64 macro as heuristic for detecting 64bit targets.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The jmp_buf type is required by the C99 specification.
Defining it for x86 fixes building the longjmp unit test.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If longjmp(jmp_buf env, int val) is called with val = 0, the setjmp()
macro must return 1.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
Layerscape update
- support sysreset,
- de-select FSL_IFC when booting from SD
- disable unused parts of ICID tables
- reduce ns_dev size for csu
- enable dma snooping for ls104x
- nand driver fixups for ls1043ardb rev 7.0 boards.
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that a unified imx8mn-u-boot is available, remove duplicated
code for generating flash.bin and other common imx8mn peripherals.
Signed-off-by: Adam Ford <aford173@gmail.com>
Multiple boards create duplicate entries in their respective
-u-boot.dtsi files which all basically do the same thing.
To consolidate these and make it easier to make improvements
going forward, consolidate them all into one place.
This file creates a flash.bin image using binman, and supports
LPDDR4, DDR4 and DDR3. Since individual boards use different
peripherals and different UART ports, those entries were kept
in their respective board files, but the spba1 node was addded
which contains all UART1-3 to help facilitate SPL_DM_SERIAL.
Individual users will still need to include their respective
UART and pinctrl nodes for those UARTS.
This consolidated file also supports generating a flash.bin file
which can boot from flexSPI if CONFIG_FSPI_CONF_HEADER is
enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The GW7904 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- 2x RS232 off-board connectors
- PMIC
- 10x bi-color LED's
- 1x miniPCIe socket with PCIe and USB2.0
- 802.3at Class 4 PoE
- 10-30VDC input via barrel-jack
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Plus PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP
devicetree file from linux-next tree.
commit <aec8ad34f7f24> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam.
General features:
- NXP i.MX8M Plus
- Up to 4GB LDDR4
- 8 eMMC
- Gigabit Ethernet
- USB 3.0, 2.0 Host/OTG
- PCIe 3.0 interface
- I2S
- LVDS
- rest of i.MX8M Plus features
i.Core MX8M Plus needs to mount on top of Engicam baseboards
for creating complete platform solutions.
Add support for it.
Sync the i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus
from Engicam devicetree file from linux-next tree.
commit <eefe06b295087> (arm64: dts: imx8mp: Add Engicam i.Core MX8M Plus SoM)
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In order to test that we properly handle watchdog(s) during the "wait
for the user to interrupt autoboot" phase, we need a watchdog device
to be watching us.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In order to test that U-Boot actually maintains the watchdog device(s)
during long-running busy-loops, such as those where we wait for the
user to stop autoboot, we need a watchdog device that actually does
something during those loops; we cannot test that behaviour via the DM
test framework.
So introduce a relatively simple watchdog device which is simply based
on calling the host OS' alarm() function; that has the nice property
that a new call to alarm() simply sets a new deadline, and alarm(0)
cancels any existing alarm. These properties are precisely what we
need to implement start/reset/stop. We install our own handler so that
we get a known message printed if and when the watchdog fires, and by
just invoking that handler directly, we get expire_now for free.
The actual calls to the various OS functions (alarm, signal, raise)
need to be done in os.c, and since the driver code cannot get access
to the values of SIGALRM or SIG_DFL (that would require including a
host header, and that's only os.c which can do that), we cannot simply
do trivial wrappers for signal() and raise(), but instead create
specialized functions just for use by this driver.
Apart from enabling this driver for sandbox{,64}_defconfig, also
enable the wdt command which was useful for hand-testing this new
driver (especially with running u-boot under strace).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmNSPhMcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDrHCACddHL6pElPVUvNWomJ
h7RNejIaFrm+V2tVoDqnUBEzxKod7g1cvBiZM+2o5fcLNIrWfH0gV+7a48Uybzt2
r7VZ9u5Rnl1Fhhjvr8eL3uF/39V249eMPrzR8xC677sCJJkcczoOw8n4y534FaJZ
1NePmMKhlo7YVEZKzwdg1sM6sUppXniSEXUllWumVaUgSHcZhFK579nCbYpt25bW
sJ1V3fY2pJnaFHv9H599zSK79Izf5fR4fr3egKZknw8oqNLKNrjkWxxlPXJfjEYr
ncFJ31dOZXJU09rRoE60nIc0QdRE8dvELjYhPKUS/wmFDg7IotwNj5GcX2RIlRPJ
mS22
=D3FL
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.01 cycle:
This small fixes set includes an indentation fix for sam9x60 DT and one
name for one pin for sama7g5.
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
When the imx8mm.dtsi file was pulled in from Linux, the UARTs
were moved into an spba sub-node which wasn't being included
in the SPL device tree. This meant the references to the UART
weren't being handled properly and when booting the system would
constantly reboot. Fix this by adding the spba node to the spl
device tree to restore normal booting.
Based on the patch from Adam Ford for the imx8mn-beacon-kit-u-boot
board.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add Serial Download Protocol support as it is a useful method to
load flash.bin to RAM and run it via 'uuu'.
With this patch, it is possible to start both U-Boot SPL and U-Boot
proper using the following 'uuu'command:
$ uuu -brun spl flash.bin
Based on a patch from Marek Vasut for the imx8mm-mx8menlo board.
Also, to fit the SPL binary into the internal RAM, select CONFIG_LTO
to reduce its size.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Enable DM USB, DM PHY and USB gadget support in imx8mm-mx8menlo SPL
to let the board continue SDP loading of second stage after the first
stage was loaded by BootROM SDP implementation. It is not possible to
jump back into BootROM v1 and let the BootROM implementation continue
the SDP loading, all this has to be performed by the U-Boot CI HDRC
controller driver and SDP protocol implementation, both of which fit
into the SPL just barely.
With this patch, it is possible to start both U-Boot SPL and U-Boot
using e.g. uuu on this board as follows:
$ uuu -brun spl flash.bin
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The signal name of pin PB2 with function F is FLEXCOM11_IO1
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The indentation went far on the right due to an extra tab for
each pinctrl sub-nodes.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
- dts update and sync for rk356x, rk3288, rk3399 from Linux;
- Add rk3399 EAIDK-610 board support;
- Update for puma-rk3399 board;
- some fix and typo fix in different drivers;
The first production revision of the MX8M Mini Menlo board implements
a hardware change which swaps console UART and another UART connector.
Implement the swap, which maps the console UART back to the way Verdin
console is mapped.
Signed-off-by: Marek Vasut <marex@denx.de>
The GW7903 revision B adds two additional GPIO's to control the
direction of the 2 isolated digital I/O circuits.
Define them as:
- dig1_ctl
- dig2_ctl
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the M2 socket gpio hogs such that they are not active on boot by
flagging them as GPIO_ACTIVE_HIGH so that 'output-high' drives high.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Update the UART config gpio hogs such that it is configured for RS232
by default on boot. Additionally rename them to match the names used
on the reset of the venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the I2C bus and set a env variable for the reset GPIO of the touch
controller. This allows us to probe the panel in a script.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adds support for the Kontron Electronics SoM SL i.MX8MM OSM-S
and the matching baseboard BL i.MX8MM OSM-S.
The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
The existing board configuration for the non-OSM SoM is reused and
allows to detect the SoM variant at runtime.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This adjusts the names of the boards and SoMs to the official naming
used by Kontron marketing. These changes also affect devicetree
names and compatibles. The same changes have been submitted to the
Linux kernel.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The new stable configuration is missing the 100mt setpoint, remove
it before updating the config to make sure the changes are separated
cleanly.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable the redundant environment feature to allow falling back in case of
storage corruption. The partition layout for the SPI NOR device is added
to the devicetree.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The display isn't and won't be used in U-Boot. Also the display setup
is not yet supported in mainline Linux, so even for cases where the
U-Boot devicetree is passed to the kernel there is currently no use
for this configuration.
Selecting the proper configuration in the kernel FIT image automatically
depending on the detected hardware can be handled by a script in the
environment.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Beside some rather unexciting sync of the DTs from the kernel tree, and
some Kconfig cleanup, there are some improvements for the ARMv5 Allwinner
family, to support boards with the F1C200s (64MB DRAM) better. We will
get actual board support as soon as the DTs have passed the Linux review
process.
There is also support for the X96 Mate TV Box, featuring the H616 SoC and
a full 4GB of DRAM.
Also we found the secret to enable SPI booting on the H616 (pin PC5 must
be pulled to GND), so the SPI boot support patch is now good to go.
Passed the gitlab CI, plus briefly tested on Pine64-LTS, LicheePi Nano,
X96 Mate and OrangePi Zero.
The IPI scheme in OpenSBI has been updated to support 8-core AE350
platform, the plicsw configuration needs to be modified accordingly.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The riscv32 toolchain for GCC-12 provided by kernel.org contains libgcc.a
compiled for double-float. To link to it we have to adjust how we build
U-Boot.
As U-Boot actually does not use floating point at all this should not
make a significant difference for the produced binaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Some boards with the Allwinner F1C100s family SoCs use UART1 for its
debug UART, so define the pins for the SPL and the pinmux name and mux
value for U-Boot proper.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
So far we stated the lack of a lowlevel() init function for the
Allwinner F1C100s board by defining the respective SKIP_* symbol in the
board's defconfig. However we don't expect any *board* to employ such
low level code, so expect this to be never used for the ARMv5 Allwinner
SoCs.
Select the appropriate symbols in the Kconfig, so that we can remove
them from the defconfig, and avoid putting them in future defconfigs for
other boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Traditionally we assumed that every Allwinner board would come with at
least 256 MB of DRAM, and set our DRAM layout accordingly. This affected
both the default load addresses, but also U-Boot's own address
expectations (like being loaded at 160 MB).
Some SoCs come with co-packaged DRAM, but only provide 32 or 64MB. So
far we special-cased those *chips*, as there was only one chip per DRAM
size. However new chips force us to take a more general approach.
Introduce a Kconfig symbol, which provides the minimum DRAM size of the
board. If nothing else is specified, we use 256 MB, and default to
smaller values for those co-packaged SoCs.
Then select the different DRAM maps according to this new symbol, so
that different SoCs with the same DRAM size can share those definitions.
Inspired by an idea from Icenowy.
This is just refactoring: compiled for all boards before and after this
patch: the binaries were identical.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The enable_caches function in architecture-specific board code is only
necessary for V7A CPUs, code for both V8A and ARM926 have already
declared this function.
Only provide our implementation of enable_caches() for V7A CPUs.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that a single binary containing TPL/SPL correctly formatted for SPI
flashes and U-Boot proper, can be generated by binman, let's do it.
Also update the documentation to tell the user to use this newly
generated file instead of manually generating and flashing the binaries.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The offset of the SPL payload on Puma is different than for other
Rockchip devices in that it is stored at offset 256K instead of much
further away in the MMC.
Flashing one binary instead of two at different offsets is much more
user friendly so let's migrate to it by modifying the offset in the Puma
specific Device Tree.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Depending on the toolchain used to compile the SPL for Puma RK3399-Q7
module, the board does not boot because the resulting binary is too big
to fit in SRAM.
Let's add a TPL so that there's no need to fiddle with or hack the
defconfig to have a working bootloader.
This follows what's been done for the majority of other RK3399-based
boards.
See the original commit for the first migrations:
bdc0008011 "rockchip: rk3399: update defconfig for TPL"
Unfortunately, the offset in SPI-NOR for U-Boot proper needs to be
modified, since the move from SPL to TPL+SPL for idbloader.img (and the
"only the first 2KB per 4KB blocks are written" "hack" for rkspi format)
increased the size above 256KB. Let's move it to 512KB to, hopefully, be
safe.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Trying to load U-Boot proper from SPL when SPL was not loaded from
SD-Card is currently not working because the SDMMC pins aren't muxed
correctly. It is assumed the BootROM is doing this for us when booting
from SD-Card hence why it's not needed when booting TPL/SPL from
SD-Card.
The pinctrl properties are removed from the SPL DT property removal list
and the pinctrl configuration nodes made available in the SPL DT, in
addition to the pull-up configurations to allow loading U-Boot proper
from SD-Card as a fallback mechanism for SPI-NOR and eMMC.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On Haikou devkit, it is possible to disable eMMC and SPI-NOR to force
booting from SD card or USB via rkdeveloptool by toggling a switch. This
switch needs to be overridden in software to be able to access eMMC and
SPI-NOR once the device has booted from SD Card. Puma SoM can override
this pin via gpio3_d5.
Until now, fixed regulator device was abused to model this, but since
there's now support for GPIO hogs, let's use it.
Since we want to be able to boot the SPL from SD Card but give it the
ability to load U-Boot proper from a fallback medium such as eMMC and
SPI-NOR, SPL support for GPIO hogs needs to be enabled too. Support for
other kinds of regulators are not needed anymore, so let's disable them.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1 work in otg mode
- 12V DC Power supply
The dts file is sync from linux-next[0].
[0]:https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/tree/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
UART0 can obviously also be used for debug uart in U-Boot, so let's add
its support.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The check to perform is on CONFIG_SPL_GPIO and not SPL_GPIO.
Because this was never compiled in, it missed an include of cru.h that
was not detected before. Let's include it too.
Also switch to IS_ENABLED in-code check as it is the preferred
inclusion/exclusion mechanism.
Fixes: 07586ee432 ("rockchip: rk3399: Support common spl_board_init")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The check to perform is on CONFIG_SPL_DM_REGULATOR and not
SPL_DM_REGULATOR. Also switch to in-code check instead of ifdefs.
Fixes: 07586ee432 ("rockchip: rk3399: Support common spl_board_init")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com> # Rock960
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Partial sync of rk3288.dtsi from Linux version 5.18
Changed:
only properties and functions that are not yet included
swap some clocks positions
fix some irq numbers
style and sort nodes
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version update the cpu and gpu nodes.
Changed:
use operating-points-v2
update thermal for all cpus
add labels to all cpus
change gpu compatible
change gpu interrupt names
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move thermal sub nodes to the dtsi
file and remove rk3288-thermal.dtsi
Changed:
replace underscore in nodename
remove comments about sensor and ID
use gpu phandle
add #cooling-cells to gpu node
lower critical temparature
remove linux,hwmon property
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The phycore_rk3288 board has a SPL size problem,
so remove phycore_init() function to stay within the limits.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These hardware register definitions are common for all K3, remove
duplicate data them by moving them to hardware.h.
While here do some minor whitespace cleanup + grouping.
Signed-off-by: Andrew Davis <afd@ti.com>
This matches how this would be done in Linux and these functions
do the alignment for us which makes the code look cleaner.
Signed-off-by: Andrew Davis <afd@ti.com>
This matches what we did for pre-K3 devices. This allows us to build
boot commands that can check for our device type at runtime.
Signed-off-by: Andrew Davis <afd@ti.com>
Move to latest DDR4 1600MT/s for k3-am64-evm based on EMIF tool
v0.08.40.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Move k3-am64-sk to use 1600MT/s LPDDR4 configuration and update to latest EMIF
tool v0.08.40.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Support VBE OS requests / fixups
Minor error-handling tweaks to bootm command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmNOjr4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreakFQf/bLTFMI8noOMa9d6Yo1RTSOa9wNiomgzC
JGY7g8i7b6cARwQ+QuSncnO/EOpwjzBLWkohUK3UAktJu2LURBPJFR4qeP01F7iz
4Mn3ikYlr3vRxAPeckN7l1aqSWrY/tEXbUdXLxSn+COzjxCQG5aBU1jd/tVBqIAk
XgZ0NGVHOQe8XOPNxDP9+EYHw4kmqMSdWZmpkb1w+Jh5AIYMMDgn1ktiNmnWXllx
LM89JxR8FMUJzFP9XBRtYemje55tAUPlENthRip9Zj9touEBbBKjV5eY8YsjpMMU
Vt5rK33vKWE4mdNBjRmOoe9xkUv/pRclpaGUFBNswf2LGw7/lsHd2A==
=3P/S
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18oct22' of https://source.denx.de/u-boot/custodians/u-boot-dm
Update uclass iterators to work better when devices fail to probe
Support VBE OS requests / fixups
Minor error-handling tweaks to bootm command
The H616 SoC uses the same SPI IP as the H6, also shares the same clocks
and reset bits.
The only real difference is a slight change in the pin assignment: the
H6 uses PC5, the H616 PC4 instead. This makes for a small change in
our spi0_pinmux_setup() routine.
Apart from that, just extend the H6 #ifdef guards to also cover the H616,
using the shared CONFIG_SUN50I_GEN_H6 symbol.
Also use this symbol for the Kconfig dependency.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Ivan Shishkin <s45rus@gmail.com>
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 32-bit SoCs, from arch/arm/boot/dts/.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
The R40 boards gain DVFS support.
Some A23/A33 tablet DTs are unified into a single file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Update the devicetree files from the Linux kernel, version v6.0-rc4.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This avoids the not backwards-compatible r_intc binding change, to allow
older kernels to boot, but the other nodes are updated.
Not much change here, the vast majority is actually cosmetic: node names
and using symbolic names for the the RTC clocks.
Some A64 boards gain some audio nodes.
The H616 DTs are now switched to the version finally merged into the
kernel, which brings some changes, but none affecting U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Fix the compilation issue when CONFIG_DEBUG_UART is activated
drivers/serial/serial_stm32.o: in function `debug_uart_init':
drivers/serial/serial_stm32.c:291: undefined reference to \
`board_debug_uart_init'
The board_debug_uart_init is needed for SPL boot, called in
cpu.c::mach_cpu_init(); it is defined in board/st/stm32mp1/spl.c.
But with the removal #ifdefs patch, the function debug_uart_init() is
always compiled even if not present in the final U-Boot image.
This patch adds a file to provided this function when DEBUG_UART and SPL
are activated.
Fixes: c8b2eef52b ("stm32mp15: tidy up #ifdefs in cpu.c")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The PWR regulators don't need be removed as they are already deactivated.
This patches is a alignment with the accepted patch in Linux device tree
in commit a34b42f8690c ("ARM: dts: stm32: fix pwr regulators references
to use scmi").
Fixes: 69ef98b209 ("ARM: dts: stm32mp15: alignment with v5.19")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix the frequencies listed in PLL configuration comments to match
the actual frequencies programmed into hardware. Furthermore, add
a comment which explains how those frequencies are calculated, so
it won't be necessary to look it up all over the datasheet and
make more mistakes in the calculation in the future.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add DT for DHCOR Testbench board, which is a testbench for testing of
DHCOR SoM during manufacturing. This is effectively a trimmed down
version of AV96 board with CSI-2 bridge, HDMI bridge, WiFi, Audio and
LEDs removed and used as GPIOs instead. Furthermore, the PMIC Buck3
is always configured from PMIC NVM to cater for both 1V8 and 3V3 SoM
variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
