Each phase is given a separate 'dtr' field so mixed protocols like
4S-4D-4D can be supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a driver for Macronix SPI controller IP.
This patch referred from linux spi-mxic.c. The difference from the
linux version is described here.
1. To adapt uboot spi framework, modify some functions naming.
2. Remove the incompatible functions of Uboot.
3. Add dummy byte recalculattion function to support dummy buswidth
not align data buswidth operation.(ex: 1-1-4, 1-1-8)
4. Add Octal mode support.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed file permission, comment line, kconfig]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Unlike imx6, on imx7 the USB PHY is described as:
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clks IMX7D_USB_PHY1_CLK>;
clock-names = "main_clk";
#phy-cells = <0>;
};
which does not have the 'reg' property.
Do not return an error when the 'reg' property is not found
for the USB PHY.
This fixes USB gadget regression on a imx7s-warp board.
Successfully tested the "ums 0 mmc 0" command on two boards:
imx7s-warp and imx6dl-pico-pi.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On a imx7s-warp board the fdtdec_get_alias_seq() function
always fails.
As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq()
inside the CONFIG_MX6 block.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Import R8A779A0 V3U PFC tables from Linux 5.12, commit 9f4ad9e425a1
("Linux 5.12") . Add parts of PFC table integration from
pinctrl: renesas: Add R8A779A0 V3U PFC tables
by Hai Pham <hai.pham.ud@renesas.com>" .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R8A779A0 V3U GPIO block has additional "General Input Enable" INEN
register. Add new R8A779A0 compatible string with a new quirk and also
a handler for this quirk which toggles the INEN register in the right
place. INEN register handling is based on "gpio: renesas: Add R8A779A0
V3U support" by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add clock tables for R8A779A0 V3U SoC from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - Add .reset_modemr_offset
- Sync tables from Linux 5.12
- Rebase on latest u-boot
On R8A779A0 V3U SoC, PLL1 and PLL5 use a divider value
from cpg_pll_configs table while PLL{20,21,30,31,4} use
different control offset. Introduce new types to handle
this and handle those types in the Gen3 clock code.
Based on "clk: renesas: Add support for R8A779A0 V3U PLLn"
by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The get_mtd_device_nm() function (code imported from Linux) simply
iterates all registered MTD devices and compares the given name with
all MTDs' names.
With SPI_FLASH_MTD enabled U-Boot registers a SPI-NOR as a MTD device
with name identical to the SPI flash chip name (from SPI ID table). Thus
for a board with multiple same SPI-NORs it registers multiple MTDs, but
all with the same name (such as "s25fl164k"). We do not want to change
this behaviour, since such a change could break existing boot scripts,
which can rely on a hardcoded name.
In order to allow somehow to uniqely select a MTD device, change
get_mtd_device_nm() function as such:
- if first character of name is '/', try interpreting it as OF path
- otherwise compare the name with MTDs name and MTDs device name.
In the following example a board has two "s25fl164k" SPI-NORs. They both
have name "s25fl164k", thus cannot be uniquely selected via this name.
With this change, the user can select the second SPI-NOR either with
"spi-nor@1" or "/soc/spi@10600/spi-nor@1".
Example:
=> mtd list
List of MTD devices:
* s25fl164k
- device: spi-nor@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/spi@10600/spi-nor@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000800000 : "s25fl164k"
* s25fl164k
- device: spi-nor@1
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/spi@10600/spi-nor@1
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000800000 : "s25fl164k"
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
In order for `mtd list` U-Boot command to list SPI NOR devices without
the need to run `sf probe` before, we have to probe SPI NOR devices in
mtd_probe_devices().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
The device_probe() function does the same thing as mtd_probe() and
mtd_probe() is only used in mtd_probe_uclass_mtd_devs(), where the
probing can be made simpler by using uclass_foreach_dev_probe macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Fill in mtd->dev member with nor->dev.
This can be used by MTD OF partition parser.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Currently when the SPI_FLASH_MTD config option is enabled, only one SPI
can be registered as MTD at any time - it is the last one probed (since
with old non-DM model only one SPI NOR could be probed at any time).
When DM is enabled, allow for registering multiple SPI NORs as MTDs by
utilizing the nor->mtd structure, which is filled in by spi_nor_scan
anyway, instead of filling a separate struct mtd_info.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add support for parsing partitions defined in device-trees via the
`partitions` node with `fixed-partitions` compatible.
The `mtdparts`/`mtdids` mechanism takes precedence. If some partitions
are defined for a MTD device via this mechanism, the code won't register
partitions for that MTD device from OF, even if they are defined.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add function for retrieving full node path of a given ofnode.
This uses np->full_name if OF is live, otherwise a call to
fdt_get_path() is made.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add functions ofnode_get_addr_size_index_notrans(), which is a
non-translating version of ofnode_get_addr_size_index().
Some addresses are not meant to be translated, for example those of MTD
fixed-partitions.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Macronix NAND Flash devices are available in different configurations
and densities.
MX"35" means SPI NAND
MX35"UF" , UF meands 1.8V
MX35LF"2G" , 2G means 2Gbits
MX35LF2G"E4" , E4 means internal ECC and Quad I/O(x4)
MX35UF4GE4AD/MX35UF2GE4AD/MX35UF1GE4AD are 1.8V 4G/2Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7983/MX35UF4GE4AD,%201.8V,%204Gb,%20v0.00.pdf
MX35UF2GE4AC/MX35UF1GE4AC are 1.8V 2G/1Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7974/MX35UF2GE4AC,%201.8V,%202Gb,%20v1.0.pdf
Validated via normal(default) and QUAD mode by read, erase, read back,
on Xilinx Zynq PicoZed FPGA board which included Macronix
SPI Host(drivers/spi/spi-mxic.c).
Signed-off-by: Jaime Liao <jaimeliao@mxic.com.tw>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
A udevice's priv space is cleared in alloc_priv() in the DM core.
Don't do it again in its probe() routine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present there is an offset of one added during the creation of
block device. This can be very confusing as we wanted to encode the
namespace id in the block device name but namespae id cannot be zero.
This changes to use the namespace id directly in the block device
name, eliminating the offset of one effectively.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present for each namespace there is a block device created for it.
There is no issue if the number of supported namespaces reported from
the NVMe device is only 1.
Since QEMU commit 7f0f1acedf15 ("hw/block/nvme: support multiple namespaces"),
the number of supported namespaces reported has been changed from 1
to 256, but not all of them are active namespaces. The actual active
one depends on the QEMU command line parameters. A common case is
that namespace 1 being active and all other 255 being inactive.
If a namespace is inactive, the namespace identify command returns a
zero filled data structure. We can use field NSZE (namespace size) to
decide whether a block device should be created for it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present the block device creation happens in the NVMe uclass
driver post_probe() phase. In preparation to support multiple
namespaces, we should issue namespace identify before creating
block devices but that touches the underlying hardware hence it
is not appropriate to do such in the uclass driver post_probe().
Let's move it to driver probe() phase instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
AQA (Admin Queue Attributes) register is a dword size with
lower word of ASQS, and higher word of ACQS.
The code set the variable aqa twice, but it is redundant.
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Each prp is 8 bytes, calculate the number of prps
per page should just divide page size by 8
there is no need to minus 1
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
writel() and co. already include the endian swap; doing the swap twice
is, er, unhelpful.
Tested on a P4080DS, which boots perfectly fine off NVMe with this.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Clocking Wizard IP supports clock circuits customized
to your clocking requirements. The wizard support for
dynamically reconfiguring the clocking primitives for
Multiply, Divide, Phase Shift/Offset, or Duty Cycle.
Limited by U-Boot clk uclass without set_phase API, this
patch only provides set_rate to modify the frequency.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
pca953x also depends on i2c that's why add dependency to Kconfig.
Where GPIO is enabled but I2C compilation error pops up.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence,
add SPI_NOR_OCTAL_READ flag for this flash.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: change order of id flags]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With a 48MHz input clock, the lowest bus frequency can be as low as
48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
the mmc framework take seconds to finish the initialization.
Limiting the minimum bus frequency to a slightly higher value can solve the
issue without any side effects.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Commit 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency") leads to
network failure on the OrangePi PC.
=> dhcp
sun8i_emac_eth_start: Timeout
According to the commit message the change of the MDIO frequency is only
required for external PHYs.
Fixes: 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Revert some changes of commit 3a97da12ee ("net: dwc_eth_qos: add dwc
eqos for imx support") that were probably added by mistake.
One of these changes can lead to received data corruption (enabling
FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings
for some platforms. And another makes some writes at unknown memory
location.
Fixes: 3a97da12ee ("net: dwc_eth_qos: add dwc eqos for imx support")
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ye Li <ye.li@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Disabling clk_ck clock leads to link up status loss in phy, which
leads to auto-negotiation restart before each network command
execution.
This issue is especially big for PXE boot protocol because of
auto-negotiation restarts before each configuration filename trial.
To avoid this issue don't disable clk_ck clock after it was enabled.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
commit f1bcad22dd ("net: e1000: add support for writing to EEPROM")
adds support for storing hwaddr in EEPROM however i210 devices do not
support this and thus results in errors such as:
Warning: e1000#0 failed to set MAC address'
Check if a flash device is present and if not return -ENOSYS indicating
this is not supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove the tab in clk_get_bulk to respect the coding rules.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add error callback in dfu stack to manage some board specific
behavior on DFU targets.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
For NOR devices the logical DFU buffer size is the sector_size,
as it is done in dfu_sf.c or in spi/sf_mtd.c
(sf_mtd_info.erasesize = flash->sector_size)
For NAND the DFU size was already limited to erasesize as
has_pages = true.
So the mtd dfu backend can use this erasesize for all the MTD devices,
NOR and NAND with dfu->max_buf_size = mtd->erasesize
This difference was initially copied from MTD command, where
data is fully available in RAM without size limitation.
This patch avoids to have many sector write in dfu_mtd.c at the end
of the DFU transfer and avoids issues with USB timeout or WATCHDOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TCF flag only means that all data was sent to FIFO. To check if the
data was sent out of FIFO we should also wait for the BUSY flag to be
cleared. Otherwise there is a race condition which can lead to
inability to write short (one byte long) data.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This driver supports Rockchip NFC (NAND Flash Controller) found on
RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been
tested using 8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to
use the BBT(bad block table).
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace msleep occurences by udelay.
drivers/pci/pcie_dw_rockchip.c:254:3: warning: implicit
declaration of function 'msleep' [-Wimplicit-function-declaration]
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the generic error number instead of specific error number.
Changes fix the below error.
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_read':
drivers/pci/pcie_dw_rockchip.c:70:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
70 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_write':
drivers/pci/pcie_dw_rockchip.c:90:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
90 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the driver for rk3568 u-boot to get sdram capacity.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.
In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes: 52faec3182 ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Stop to initialize the PCIe controller if it's disabled by RCW.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that we have only one clock driver, we don't need to have our own
subdirectory. Move the driver back with the rest of the clock drivers.
The MAINTAINERS for kendryte pinctrl is also fixed since it has always been
wrong.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This driver no longer serves a purpose now that we have moved away from
CCF. Drop it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This speeds up boot by preventing multiple reconfigurations of the PLLs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds support for setting clock rates, which was left out of the
initial CCF expunging. There are several tricky bits here, mostly related
to the PLLS:
* The PLL's bypass is broken. If the PLL is reconfigured, any child clocks
will be stopped.
* PLL0 is the parent of ACLK which is the CPU and SRAM's clock. To prevent
stopping the CPU while we configure PLL0's rate, ACLK is reparented
to IN0 while PLL0 is disabled.
* PLL1 is the parent of the AISRAM clock. This clock cannot be reparented,
so we instead just disallow changing PLL1's rate after relocation (when
we are using the AISRAM).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since we are no longer using CCF we cannot use the default soc_clk_dump.
Instead, implement our own.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Now that there no separate PLL driver, we can no longer make the PLL
functions static. By moving the PLL driver in with the rest of the clock
code, we can make these functions static again. We still keep the pll
header for unit testing, but it is pretty reduced.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is effectively a complete rewrite to remove all dependency on CCF.
The code is now smaller, and so is the binary. It also takes up less memory
at runtime (since we don't have to create 40 udevices). In general, I am
much happier with this driver as much of the complexity and late binding
has been removed.
The k210_*_params structs which were previously used to initialize CCF
clocks are now used as the complete configuration. Since we can write our
own division logic, we can now do away with several "half" clocks which
only existed to provide constant factors of two.
The clock IDs have been renumbered to remove unused clocks. This may not be
the last time they are renumbered, since we have diverged with Linux. There
are also still a few clocks left out which may need to be added back in.
In general, I have tried to leave out behavioral changes. However, there is
a small bugfix regarding ACLK. According to the technical reference manual,
its mux comes *after* its divider (which is present only for PLL0). This
would have required yet another intermediate clock to fix with CCF, but
with the new driver it is just 2 lines of code :)
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Since 291da96b8e ("clk: Allow clock defaults to be set during re-reloc
state for SPL only") it has been impossible to set clock defaults before
relocation. This is annoying on boards without SPL, since there is no way
to set clock defaults before U-Boot proper. In particular, the aisram rate
must be changed before relocation on the K210, since U-Boot will hang if we
try and change the rate while we are using aisram.
To get around this, extend the stage parameter to allow force setting
defaults, even if they would be otherwise postponed for later. A device
tree property was decided against because of the concerns in the original
commit thread about the overhead of repeatedly parsing the device tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup TCHAN/RCHAN/RFLOW cfg registers.
Add support for the same.
Note that we still need to send chan/flow cfg message to TIFS via TISCI
client driver in order to open up firewalls around chan/flow but setting
up of cfg registers is handled locally.
U-Boot specific code is in a separate file included in main driver so
as to maintain similarity with kernel driver in order to ease porting of
code in future.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-8-vigneshr@ti.com
In absence of Device Manager (DM) services such as at R5 SPL stage,
driver will have to natively setup Ring Cfg registers. Add support for
the same.
Note that we still need to send RING_CFG message to TIFS via TISCI
client driver in order to open up firewalls around Rings.
U-Boot specific code is in a separate file included in main driver so
as to maintain similarity with kernel driver in order to ease porting of
code in future.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-7-vigneshr@ti.com
On J721e and J7200, MCU R5 core (boot master) itself would run Device
Manager (DM) Firmware and interact with TI Foundational Security (TIFS)
firmware to enable DMA and such other Resource Management (RM) services.
So, during R5 SPL stage there is no such RM service available and ti_sci
driver will have to directly interact with TIFS using DM to DMSC
channels to request RM resources.
Therefore add DT binding and driver for the same. This driver will
handle Resource Management services at R5 SPL stage.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-4-vigneshr@ti.com
In case of R5 SPL, GET_RANGE API service is not available (as DM
services are not yet up), therefore service such calls locally using
per SoC static data.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-3-vigneshr@ti.com
R5 SPL would need to talk to DMSC using DM to DMSC sec-proxy threads.
Mark these as valid threads in the driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210607141753.28796-2-vigneshr@ti.com
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Normally, power domains are handled via TI-SCI in K3 SoCs. However,
SPL is not going to have access to sysfw resources, so it must control
them directly. Add driver for supporting this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add driver to support TI K3 generation SoC clocks. This driver registers
the clocks provided via platform data, and adds support for controlling
the clocks via DT handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add support for TI K3 SoC PLLs. This clock type supports
enabling/disabling/setting and querying the clock rate for the PLL. The
euclidean library routine is used to calculate divider/multiplier rates
for the PLLs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Clock rates are cached within the individual clock nodes, and right now
if one changes a clock rate somewhere in the middle of the tree, none
of its child clocks notice the change. To fix this, clear up all the
cached rates for us and our child clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
If a clock provider is not ready for assigning default rates/parents
during its probe, it may return -EPROBE_DEFER directly from xlate.
Handle this special case properly by skipping the entry and adjusting the
return value to pass. The defaults will be handled properly in post probe
phase then.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Set rate should return the new clock rate on success, and negative error
value on failure. Fix this, as currently set_rate returns 0 on success.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Bail out early if device returned for the parent clock is null.
This avoids warning prints like this when doing clk dump:
dev_get_uclass_priv: null device
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Current driver only supports registering fixed rate clocks from DT. Add
new API which makes it possible to register fixed rate clocks directly
from e.g. platform specific clock drivers.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
With the sysfw rearch, sysfw PM calls are no longer available from SPL
level. To properly support this, remove the is_on checks and the reset
assertion from the R5 remoteproc driver as these are not supported.
Attempting to access unavailable services will cause the device to hang.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.
Add dummy write to genfifo register in chipselect.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
On reset, the RTC loads the 2000-01-01 date with a wrong day of the
week (Sunday instead of Saturday).
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-9-dariobin@libero.it
Update the driver to support the device tree and the driver model.
The read / write helpers in rtc_ops allow access to scratch registers
only. The offset parameter is added to the address of the scratch0
register.
Support for non-DM has been removed as there were no users.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-8-dariobin@libero.it
The RTC module contains a kicker mechanism to prevent any spurious
writes from changing the register values. To set the time, you must
first unlock the TC registers, update them and then lock.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-6-dariobin@libero.it
To write correct data to the TC registers, the STATUS register must be
read until the BUSY bit is equal to zero. Once the BUSY flag is zero,
there is a 15 μs access period in which the TC registers can be
programmed.
The rtc_wait_not_busy() has been inspired by the Kernel.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-5-dariobin@libero.it
Use 32-bit access only where it is needed. Most of the RTC registers
contain useful information in the 8 least significant bits, the others
are reserved.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-4-dariobin@libero.it
The Davinci's onchip RTC is also present on TI OMAP1, AM33XX, AM43XX and
DRA7XX SOCs. So, let's enable compilation for these architectures too.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210602203805.11494-2-dariobin@libero.it
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Some SoC needs "disp_axi" clock to be enabled, so let's try to retrieve it
and enabling. If it fails it gives only a debug(), but this clock as well
as "axi" clock is not mandatory.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
On some SoC mxsfb needs more than one clock gate(actual "per" clock). So
let's introduce "axi" clock that can be provided but it's not mandatory.
This is inspired from linux mxsfb driver. Also let's rename "per" clock to
"pix" clock for compatibility with already existing .dts lcdif nodes
implementation.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
