This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.
The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Clean up the naming of pinmux-related objects:
* Refer to drive groups rather than pad groups to match the Linux kernel.
* Ensure all pinmux API types are prefixed with pmux_, values (defines)
are prefixed with PMUX_, and functions prefixed with pinmux_.
* Modify a few type names to make their content clearer.
* Minimal changes to SoC-specific .h/.c files are made so the code still
compiles. A separate per-SoC change will be made immediately following,
in order to keep individual patch size down.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove a few unused functions from the pinmux header. They aren't
currently used, and removing them prevents any new usage from appearing.
This will ease moving to just pinmux_config_table() and
padgrp_config_table() in the future.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Much of arch/arm/cpu/tegra*-common/pinmux.c is identical. Remove the
duplication by creating pinmux-common.c for all the identical code.
This leaves:
* arch/arm/include/asm/arch-tegra*/pinmux.h defining only the names of
the various pins/pin groups, drive groups, and mux functions.
* arch/arm/cpu/tegra*-common/pinmux.c containing only the lookup table
stating which pin groups support which mux functions.
The code in pinmux-common.c is semantically identical to that in the
various original pinmux.c, but had some consistency and cleanup fixes
applied during migration.
I removed the definition of struct pmux_tri_ctlr, since this is different
between SoCs (especially Tegra20 vs all others), and it's much simpler to
deal with this via the new REG/MUX_REG/... defines. spl.c, warmboot.c,
and warmboot_avp.c needed updates due to this, since they previously
hijacked this struct to encode the location of some non-pinmux registers.
Now, that code simply calculates these register addresses directly using
simple and obvious math. I like this method better irrespective of the
pinmux code cleanup anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's "APB misc" register region contains various miscellaneous
registers and the Tegra pinmux registers. Some code that touches the
misc registers currently uses struct pmux_tri_ctlr, which is intended to
be a definition of pinmux registers, rather than struct apb_misc_pp_ctrl,
which is intended to be a definition of the miscellaneous registers.
Convert all such code to use struct apb_misc_pp_ctrl, since struct
pmux_tri_ctlr goes away in the next patch.
This requires adding a missing field definition to struct
apb_misc_pp_ctrl, and moving the header into a more common location.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pinmux_init() is a board-level function, not a pinmux driver function.
Move the prototype to a board header rather than the driver header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For consistency with other SoCs, modify Tegra20's enum pmux_func to:
* Remove PMUX_FUNC values that aren't real
* Use the same PMUX_FUNC_RSVD[1-4] values, and ensure (RSVD1 & 3)==0;
this will be assumed by pinmux_set_func() in a future patch.
Unfortunately, PMUX_FUNC_RSVD is still used in the pin macros. Use a
private define inside the driver to prevent this from causing compilaton
errors. This will be cleaned up when the pin tables are re-written in a
later patch in this series.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This field isn't used anywhere, so remove it. Note that PIN() macros are
left unchanged for now, to avoid many diffs to them; later commits will
completely rewrite them just one time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit d016dc42ce changed the layout of BCH8 SW
on omap3 boards. We need to adopt the ecc layout for the nand_spl_simle
driver to avoid wrong ecc errors.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Commit 890880583d introduced EEPROM parsing and
board detection but faild to return a valid tricorder_eeprom struct for backup
case. When pressing S200 while reading EEPROM we ignore the value. We
returned falsely a tricorder_eeprom struct with uninitialized data which is
just garbage.
Initialize it by zeroing the whole structure.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
During switch to device tree, commit 1ecab0f has removed this code.
INFORM4 and INFORM5 registers are used by TRATS2 first stage bootloader for
providing recovery. For normal operation, those two must be cleared out.
This error emerges when one force reset from u-boot's command line for
three times.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
In some use cases, SPL linker script was not updated even when
it should be.
For instance,
$ make tricoder_config all
[ build complete ]
... modify include/configs/tricoder.h
$ make
spl/u-boot-spl.lds should be updated in this case, but it wasn't.
To fix this problem, linker scripts generation should be handled
by $(call if_changed_dep,...) rather than by $(call if_changed,...).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reported-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch add gicv3 support to uboot armv8 platform.
Changes for v2:
- rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
- move smp_kick_all_cpus() from gic.S to start.S, it would be
implementation dependent.
- Each core initialize it's own ReDistributor instead of master
initializeing all ReDistributors. This is advised by arnab.basu
<arnab.basu@freescale.com>.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
When flush the d$ with set/way instruction, it need calculate the way's
offset = log2(Associativity); but in current uboot's code, it use below
formula to calculate the offset: log2(Associativity * 2 - 1), so finally
it cannot flush data cache properly.
Signed-off-by: Leo Yan <leoy@marvell.com>
For ARMv8, U-boot has been running at EL3 with cache and MMU enabled.
Without proper setup for EL2, cache and MMU are both disabled (out of
reset). Before switching, we need to flush the dcache to make sure the
data is in the main memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: David.Feng <fenghua@phytium.com.cn>
This patch contains several changes required for second Ethernet
(enet1/RMII1) port on vf610
- ANADIG PLL5 control definitions required for Ethernet RMII1 clock
- Secondary Ethernet (enet1) MAC RMII1 base address definition
- RMII1 iomux definitions
- VF610_PAD_PTA6__RMII0_CLKOUT iomux definition required for
internal (e.g. crystal-less) Ethernet clocking.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
The anadig_reg structure started at the wrong offset (fixed by adding
reserved_0x000[4]), was missing some reserved field required for
alignment purpose (reserved_0x094[3] between pll4_denom and pll6_ctrl)
and further contained a too short reserved field causing further miss-
alignment (reserved_0x0C4[7]). Also, rename all the reserved fields
and using a memory offset based scheme for.
Discovered and tested by temporarily putting the following debug
instrumentation into board_init():
struct anadig_reg *anadig = (struct anadig_reg *)ANADIG_BASE_ADDR;
printf("&anadig->pll3_ctrl=0x%p\n", &anadig->pll3_ctrl);
printf("&anadig->pll5_ctrl=0x%p\n", &anadig->pll5_ctrl);
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[stefan@agner.ch: regrouped patch]
Signed-off-by: Stefan Agner <stefan@agner.ch>
After Kbuild introduction, the CROSS_COMPILE environment variable has been
set to some default value (prefix arm-linux-).
This shall be removed since it breaks building u-boot for native arm target
(like qemu ARM).
Moreover not all compilers have arm-linux- prefix.
Additionally the u-boot cross compiles with CROSS_COMPILE= set explicitly-
e.g.:
CROSS_COMPILE=/ .... /arm-v7a-linux-gnueabi- make
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Full cache line writes to the same memory region from at least two
processors might deadlock the processor. Exists on r1, r2, r3
revisions.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
A short loop including a DMB instruction might cause a denial of
service on another processor which executes a CP15 broadcast operation.
Exists on r1, r2, r3, r4 revisions.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
When SoC first boots up, we should invalidate the cache but not flush it.
We can use the same function for invalid and flush mostly, with a wrapper.
Invalidating large cache can ben slow on emulator, so we postpone doing
so until I-cache is enabled, and before enabling D-cache.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
If D-cache is enabled, we need to flush it, and invalidate i-cache before
jumping to the new location. This should be done right after relocation.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
Move setting for MAIR and TCR to cache_v8.c, to avoid conflict with
sub-architecture.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: David Feng <fenghua@phytium.com.cn>
Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
We've run into a non-trivial conversion to CONFIG_SYS_GENERIC_BOARD so
we'll postpone this notice until right after v2014.04 is out.
This reverts commit 36c4b1d980.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds the groundwork for generating signed BootStream, which
can be used by the HAB library in i.MX28. We are adding a new target,
u-boot-signed.sb , since the process for generating regular non-signed
BootStream is much easier. Moreover, the signed bootstream depends on
external _proprietary_ _binary-only_ tool from Freescale called 'cst',
which is available only under NDA.
To make things even uglier, the CST or HAB mandates a kind-of circular
dependency. The problem is, unlike the regular IVT, which is generated
by mxsimage, the IVT for signed boot must be generated by hand here due
to special demands of the CST. The U-Boot binary (or SPL binary) and IVT
are then signed by the CST as a one block. But here is the problem. The
size of the entire image (U-Boot, IVT, CST blocks) must be appended at
the end of IVT. But the size of the entire image is not known until the
CST has finished signing the U-Boot and IVT. We solve this by expecting
the CST block to be always 3904B (which it is in case two files, U-Boot
and the hand-made IVT, are signed in the CST block).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This change enables automatically uuid generation by command gpt.
In case of updating partitions layout user don't need to care about
generate uuid manually.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
Changes:
- randomly generate partition uuid if any is undefined and CONFIG_RAND_UUID
is defined
- print debug info about set/unset/generated uuid
- update doc/README.gpt
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Those commands basis on implementation of random UUID generator version 4
which is described in RFC4122. The same algorithm is used for generation
both ids but string representation is different as below.
char: 0 9 14 19 24 36
xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
UUID: be be be be be
GUID: le le le be be
Commands usage:
- uuid [<varname>]
- guid [<varname>]
The result is saved in environment as a "varname" variable if argument is given,
if not then it is printed.
New config:
- CONFIG_CMD_UUID
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
This patch adds support to generate UUID (Universally Unique Identifier)
in version 4 based on RFC4122, which is randomly.
Source: https://www.ietf.org/rfc/rfc4122.txt
Changes:
- new configs:
- CONFIG_LIB_UUID for compile lib/uuid.c
- CONFIG_RANDOM_UUID for functions gen_rand_uuid() and gen_rand_uuid_str()
- add configs dependency to include/config_fallbacks.h for lib uuid.
lib/uuid.c:
- add gen_rand_uuid() - this function writes 16 bytes len binary representation
of UUID v4 to the memory at given address.
- add gen_rand_uuid_str() - this function writes 37 bytes len hexadecimal
ASCII string representation of UUID v4 to the memory at given address.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
[trini: Add CONFIG_EFI_PARTITION to fallbacks]
Signed-off-by: Tom Rini <trini@ti.com>
Changes in lib/uuid.c to:
- uuid_str_to_bin()
- uuid_bin_to_str()
New parameter is added to specify input/output string format in listed functions
This change allows easy recognize which UUID type is or should be stored in given
string array. Binary data of UUID and GUID is always stored in big endian, only
string representations are different as follows.
String byte: 0 36
String char: xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
string UUID: be be be be be
string GUID: le le le be be
This patch also updates functions calls and declarations in a whole code.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
This commit introduces cleanup for uuid library.
Changes:
- move uuid<->string conversion functions into lib/uuid.c so they can be
used by code outside part_efi.c.
- rename uuid_string() to uuid_bin_to_str() for consistency with existing
uuid_str_to_bin()
- add an error return code to uuid_str_to_bin()
- update existing code to the new library functions.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
Commit 2faf5fb82e introduced a regression that causes a data
abort when running scsi init followed by scsi reset.
There are 2 problems with the original commit
1) ALLOC_CACHE_ALIGN_BUFFER() allocates memory on the stack but is
assigned to ataid[port] and used by other functions.
2) The function ata_scsiop_inquiry() tries to free memory which was
never allocated on the heap.
Fix these problems by using tmpid as a temporary cache aligned buffer.
Allocate memory separately for ataid[port] and re-use it if required.
Fixes: 2faf5fb82e (ahci: Fix cache align error messages)
Reported-by: Eli Nidam <elini@marvell.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
The u-boot's image TEXT_BASE needs to be changed to 0x43e00000 from 0x78100000.
This change provides compatibility with other trats2 (RD_PQ) devices
(http://download.tizen.org/releases/system/).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
1. The Data timeout counter value in eSDHC_SYSCTL register is
not working as it should be, so add quirks to enable this
workaround to fix it to the max value 0xE.
2. Add CONFIG_SYS_FSL_ERRATUM_ESDHC111 to enable its workaround.
* Update of patch for change mmc interface by
Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The controller reset is performed now if command error occurs.
This commit adds the reset for the case of data related errors too.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Calculation of the timeout value should be based on actual clock value,
written to controller registers. Since mmc->tran_speed is either the
maximum allowed speed, or the preliminary value, that is be not yet
set to registers, the actual timeout, taken by the controller, based
on its clock settings, may be much longer than expected, based on
mmc->tran_speed value. In particular it happens at early initialization
stage, when typical value of mmc->tran_speed is 20MHz or 26MHz, while
actual clock setting, configured in the controller, is 400kHz.
It's more correct to use mmc->clock value for timeout calculation instead.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Some eMMC chips may need the RST_n_FUNCTION bit set to a non-zero value
in order for warm reset of the system to work. Details on this being
required will be part of the eMMC datasheet. Also add using this
command to the dra7xx README.
* Whitespace fix by panto
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
