Commit graph

50 commits

Author SHA1 Message Date
Nobuhiro Iwamatsu
dcd18eaf61 net: sh-eth: Add to Kconfig and convert
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-01-15 12:05:26 -06:00
Wilson Lee
4bf56913d0 net: macb: Add support for Xilinx Zynq SoC
Although Xilinx Zynq SoC was using MACB similar hardware. However,
U-boot MACB driver was not supporting Xilinx Zynq SoC. This patch is
to add support for the Xilinx Zynq SoC to the existing MACB network
driver.

This patch is to add Zynq GEM DMA Config, provide callback
function for different linkspeed for case of using Xilinx Zynq
Programmable Logic as GMII to RGMII converter.

This patch convert the return value to use error codes.

Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-01-15 12:05:14 -06:00
Tom Rini
6bf634223a Merge git://git.denx.de/u-boot-fsl-qoriq 2018-01-11 11:18:49 -05:00
Ahmed Mansour
541d57663f configs: Move SYS_DPAA_QBMAN to Kconfig
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part

Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-10 12:28:58 -08:00
Miquel Raynal
e7ab2ccd15 ARM: mvebu: Allow MVNETA to be selected with Armada 3700 SoCs
Until now, Armada 3700 SoCs could not enable the mvneta driver, and thus
did not benefit from Ethernet support. Add ARMADA_3700 in the
"depends on" list of the MVNETA Kconfig entry.

Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-01-09 16:41:00 +01:00
Stefan Mavrodiev
aba3924927 sunxi: Fix A20-OLinuXino-MICRO LAN8710 support
>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-12-07 10:57:23 +05:30
Artturi Alm
6270a3f035 sunxi: restore PHYLIB for CONFIG_SUN4I_EMAC users
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h,
likely missed in:
	commit 3146f0c017 ("Move PHYLIB to Kconfig")

Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-09 14:39:30 +05:30
Adam Ford
8daec2d9d3 net: Add SMC911X driver to Kconfig, convert
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
   CONFIG_SMC911X
   CONFIG_SMC911X_BASE
   CONFIG_SMC911X_16_BIT
   CONFIG_SMC911X_32_BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 21:40:26 -04:00
Chris Packham
7654f62f4e ARM: mvebu: Convert CONFIG_MVNETA to Kconfig
This converts the following to Kconfig:
   CONFIG_MVNETA

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:30 +02:00
Suji Velupillai
c89782dcac net: move Broadcom SF2 driver to Kconfig
move to Kconfig:
	CONFIG_BCM_SF2_ETH
	CONFIG_BCM_SF2_ETH_DEFAULT_PORT
	CONFIG_BCM_SF2_ETH_GMAC

Also modified defconfigs of all platforms that use these configs.

Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:18:30 -05:00
Christophe Leroy
fad51ac3af powerpc, 8xx: move FEC Ethernet driver in drivers/net
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2017-07-08 15:56:02 -04:00
Philipp Tomsich
449ea2cd0d net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable
This change migrate the following configuration options for Kconfig:
 * PHY_GIGE, indicates that a controller (with an appropriate PHY) is
   Gigabit capable and enables extra support in the miiutil for
   parsing the status of Gigabit PHYs
 * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs,
   which previously had to enabled through a board-specific config file

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-06-02 14:44:18 -05:00
Tom Rini
8dc1b17f14 Merge branch 'master' of git://git.denx.de/u-boot-nds32
Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	drivers/net/Kconfig
2017-05-26 11:18:53 -04:00
rick
be71a179bd nds32: eth: Support ftmac100 DM.
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
 Boot linux kernel via dhcp and bootm ok.

 NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
 NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
 BOOTP broadcast 1
 BOOTP broadcast 2
 BOOTP broadcast 3
 BOOTP broadcast 4
 DHCP client bound to address 10.0.4.178 (4899 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'boomimage-310y-ae300-spi.bin'.
	Load address: 0x600000
	Loading: #################################################################
	         #################################################################
	         #################################################################
...
...
	         ###################################
	         233.4 KiB/s
					 done
					 Bytes transferred = 13872076 (d3abcc hex)
	NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
	BOOTP broadcast 1
	BOOTP broadcast 2
	BOOTP broadcast 3
	BOOTP broadcast 4
	DHCP client bound to address 10.0.4.178 (4592 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'ae300.dtb'.
	Load address: 0x2000000
	Loading: #
	         82 KiB/s
					 done
					 Bytes transferred = 2378 (94a hex)
	NDS32 # bootm 0x600000 - 0x2000000
	 Image Name:
	 Created:      2017-03-22   6:52:03 UTC
	 Image Type:   NDS32 Linux Kernel Image (uncompressed)
	 Data Size:    13872012 Bytes = 13.2 MiB
	 Load Address: 0000c000
	 Entry Point:  0000c000
	 Verifying Checksum ... OK
	 Booting using the fdt blob at 0x2000000
	 Loading Kernel Image ... OK
	 Loading Device Tree to 01efc000, end 01eff949 ... OK
	 Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
	(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
  #293 PREEMPT Wed Mar 22 14:49:28 CST 2017
	CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick <rick@andestech.com>
2017-05-23 13:48:27 +08:00
Marek Vasut
8ae51b6f32 net: ravb: Add Renesas Ethernet RAVB driver
Add driver for the Renesas Ethernet AVB block found in RCar H3/M3.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Based on work of:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
2017-05-22 04:38:24 +09:00
Mylène Josserand
751b0be0a1 sunxi: Convert CONFIG_RGMII to Kconfig
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:20:29 +02:00
Mylène Josserand
abc3e4df59 sunxi: Convert SUNXI_EMAC to Kconfig
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:19:59 +02:00
Mylène Josserand
4d43d065db sunxi: Move SUNXI_GMAC to Kconfig
Move the SUNXI_GMAC config option to Kconfig, remove it
from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC.

Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:19:56 +02:00
Stefan Roese
e7935c4770 net: mvpp2: Enable compilation for Armada 7K/8K platforms
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-03-29 07:42:20 +02:00
Tom Rini
7131d2d06b drivers/net/Kconfig: Correct use of apostrophe
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-27 12:14:58 -05:00
Alex
af2cbfd6b9 drivers: net: Provide Kconfig menu for PHYLIB
Provide the necessary Kconfig symbols so that PHYLIB support may be
enabled in Kconfig, as opposed to needing to #define these symbols in
C source headers.

BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as
they don't seem to explicitly depend on it (i.e. they do not use the
phy_driver class).

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07 11:05:03 -06:00
Wenyou Yang
ebcb40a5a0 net: Kconfig: Add CONFIG_MACB option
Add CONFIG_MACB option in KConfig to be used to select the Cadence
MACB Ethernet driver.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-02-07 10:54:31 -06:00
Sjoerd Simons
0125bcf01c net: gmac_rockchip: Add Rockchip GMAC driver
Add a new driver for the GMAC ethernet interface present in Rockchip
RK3288 SOCs. This driver subclasses the generic design-ware driver to
add the glue needed specifically for Rockchip.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-01-11 20:23:50 -07:00
Patrick Bruenn
98d62e618b arm: imx: add i.MX53 Beckhoff CX9020 Embedded PC
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.

The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2016-12-16 12:57:12 +01:00
Stephen Warren
ba4dfef146 net: add driver for Synopsys Ethernet QoS device
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org> # V1
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-11-07 11:28:15 -06:00
Jagan Teki
97d29ca3a8 net: Kconfig: Add FEC_MXC entry
Added kconfig for FEC_MXC driver.

Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Zubair Lutfullah Kakakhel
2f1f05f432 net: emaclite: Enable driver for MIPS
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-21 14:55:14 +02:00
Max Filippov
f0727120a7 net/ethoc: add Kconfig entry for the driver
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.

Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15 13:34:46 -05:00
Amit Singh Tomar
a29710c525 net: Add EMAC driver for H3/A83T/A64 SoCs.
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).

BIG Thanks to Andre for providing some of the DT code.

Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-15 08:34:34 +02:00
Marek Vasut
e40095f63b net: Add ag7xxx driver for Atheros MIPS
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines.
The driver could be easily extended to other WiSoCs.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wills Wang <wills.wang@live.com>
[fixed Kconfig dependency]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-05-31 09:38:11 +02:00
Stefan Roese
99d4c6d3b2 net: mvpp2.c: Add Marvell mvpp2 network driver for Armada 375
This patch adds support for the mvpp2 ethernet controller which is integrated
in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4),
which has been stripped of the in U-Boot unused portions.

Tested on the Marvell Armada 375 eval board db-88f6720.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
2016-04-04 11:21:40 +02:00
Michael Haas
525d187afb net: phy: Optionally force master mode for RTL PHY
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.

This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.

There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.

CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com

Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 14:29:11 +02:00
Bin Meng
0764f24ae6 net: Move CONFIG_RTL8169 to Kconfig
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Stephen Warren <swaren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-03-22 12:19:53 -04:00
Bin Meng
86e9dc86b1 net: Move CONFIG_RTL8139 to Kconfig
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig
to use that.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Fixup MPC8641HPCN* and r2dplus configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-03-22 12:19:27 -04:00
Purna Chandra Mandal
23e7578c9b drivers: net: Add ethernet driver for Microchip PIC32.
This driver implements MAC and MII layer of the ethernet controller.
Network data transfer is handled by controller internal DMA engine.
Ethernet controller is configurable through device-tree file.

Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
2016-02-01 22:14:02 +01:00
Michal Simek
3229c869aa net: emaclite: Move emaclite to Kconfig
Add PHYLIB and MII dependencies and enable it by default for Microblaze.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:52 +01:00
Michal Simek
338a5f2bf1 net: Add axi emac to Kconfig
Also add dependency on PHYLIB and MII which is required.
Clean PHYLIB dependency from the driver too.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27 15:55:51 +01:00
Thomas Chou
25af71c4bf net: eth_designware: select PHYLIB in Kconfig
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.

This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-22 04:42:27 +01:00
Michal Simek
7bccc75a2b net: gem: Add driver dependencies to PHYLIB
Clear driver dependecies via Kconfig. Remove PHYLIB dependency from
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18 13:15:58 +01:00
Michal Simek
c942810787 net: gem: Fix typo in Kconfig entry
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-18 13:15:58 +01:00
Michal Simek
596e5782e7 net: gem: Move gem to Kconfig
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-12-07 10:14:28 +01:00
Thomas Chou
96fa1e4385 net: convert altera_tse to driver model and phylib
Convert altera_tse to driver model and phylib.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-10-23 14:55:48 +08:00
Bin Meng
b68fe15227 net: pch_gbe: Add Kconfig option
Add Kconfig option in preparation for moving board to use Kconfig.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-09-09 07:48:03 -06:00
Simon Glass
c294ac5c16 net: e1000: Add Kconfig options
Add Kconfig options in preparation for moving boards to use Kconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-08-21 16:33:39 -05:00
Joe Hershberger
ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00
Simon Glass
ef48f6dd30 Kconfig: Move CONFIG_DESIGNWARE_ETH to Kconfig
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-04-18 11:11:36 -06:00
Joe Hershberger
a346ca7902 sandbox: eth: Add a bridge to a real network for sandbox
Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.

This raw Ethernet API requires elevated privileges.  You can either run
as root, or you can add the capability needed like so:

sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:13 -06:00
Joe Hershberger
3ea143abe9 sandbox: eth: Add network support to sandbox
Add basic network support to sandbox which includes a network driver.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:12 -06:00
Joe Hershberger
05c3e68f85 dm: eth: Add basic driver model support to Ethernet stack
First just add support for MAC drivers.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:12 -06:00
Masahiro Yamada
ed36323f6d kconfig: add blank Kconfig files
This would be useful to start moving various config options.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-09-24 18:30:28 -04:00