For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
In case the i.MX8M Plus starts from eMMC BOOT1/BOOT2 HW partitions, the
flash.bin container is stored at offset 0 from the start, that means the
fitImage itb is at offset 0x2c0 instead of 0x300 sectors from the start.
Handle this difference in custom spl_mmc_get_uboot_raw_sector() .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update RAM Timings for 2GB RAM based on DDR Controller Configuration
Spreadsheet revision 22. Including the update of the refresh
rate to workaround errata ERR050805.
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Running a memtest in U-Boot and Linux shows that some Colibri iMX6
produce bitflips at temperatures above 60°C. This happens because the
RALAT and WALAT values on the Colibri iMX6 are too low. The problems
were introduced by commit 09dbac8174 ("mx6: ddr: Restore ralat/walat
in write level calibration") before the calibration process overwrote
the values and set them to the maximum value. With this commit, we make
sure that the RALAT and WALAT values are set to the maximum values
again. This has been proven to work for years.
Fixes: 09dbac8174 ("mx6: ddr: Restore ralat/walat in write level calibration")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since U-Boot builds HTML documentation, migrate the contents
of the README file to an rst file which can generate the
proper outputs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mn_beacon.env and reference it from the defconfigs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Since U-Boot builds HTML documentation, migrate the contents
of the README file to an rst file which can generate the
proper outputs.
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of cluttering up a header file with a bunch of defines,
move the default environmental variables to a file called
imx8mm_beacon.env and reference it from the defconfig.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
The in-spl enabled DM serial console requires the board setup to be
able to parse SPL_OF_PLATDATA based serial driver (pl01x) for the
imx28 based XEA board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code fixes following WARNING:
DTOC spl/dts/dt-plat.c
fsl_imx28_clkctrl: WARNING: the driver fsl_imx28_clkctrl was not found in the driver list
As imx28 doesn't yet support common clock framework, this prevents from
DTOC warnings during SPL build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add new i.MX 8M Plus Quad SKU to ConfigBlock handling.
0070: Verdin iMX8M Plus Quad 8GB WB IT
This SKU is identical to 0066 but supporting Industrial Temperature range.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The update_firmware script is intended to update the boot firmware but
the details including the offset and hardware partition are dependent
on the boot device.
Specifically:
- IMX8MM/IMX8MP (BOOTROM v2) the offset is 32KiB for SD and eMMC user
hardware partition and 0KiB for eMMC boot partitions.
- IMX8MM the offset is 33KiB for SD and eMMC regardless of hardware
partition.
Dynamically set soc, dev, bootpart, and bootblk env vars at runtime
and use these in the update_firmware script. Remove the splblk env var
from config files as its no longer needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Determine the U-Boot env hardware partition depending on the boot
device.
This allows the same boot firmware image to be placed on user, boot0,
or boot1 without changing CONFIG_SYS_MMC_ENV_PART.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to adjust for
IMX8MN and IMX8MP when booting from an eMMC boot partition due
to IMX BOOTROM v2 using an SPL offset of 0 for boot partitions
and 32K for the user partition.
In order to allow the same firmware to run on both user and boot
hardware partitions adjust raw_sect dynamically at runtime.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The imx8mm_beacon SOM has a QSPI part attached to the FSPI controller.
Update the header and spl files to support booting from NOR flash and
add imx8mm_beacon_fspi_defconfig to support this configuration.
Signed-off-by: Adam Ford <aford173@gmail.com>
The dts sync from Linux leaves mac0/ethernet1 enabled on icicle, but
U-Boot does not currently set a mac address for it. Expand on the code
which currently sets the mac for mac1/ethernet0 to optionally set the
mac address for the second ethernet.
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
For changing the USB OTG node status from "okay" to "disabled" more
space is needed, so call fdt_increase_size() to avoid the following
error:
```
U-Boot 2023.07-rc5-0.0.0-devel+git.580eb31199be (Jun 27 2023 - 13:39:58 +0000)
CPU: Freescale i.MX7S rev1.2 800 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 30C
Reset cause: POR
DRAM: initcall sequence 8786eafc failed at call 8781b351 (err=-3)
### ERROR ### Please RESET the board ###
```
Ideally, fdt_status_disabled() should call fdt_increase_size() internally,
so that there would be no need for manually calling it in board code.
Do it manually for now to fix the regression.
Based on the code from board/CZ.NIC/turris_omnia/turris_omnia.c.
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Colibri iMX7S
board_mmc_get_env_part() is not called as the default implementation
of mmc_get_env_part() is used.
Fix this problem by directly calling mmc_get_env_part() instead.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
This fixes access to camera sensor over I2C during probe time in
the kernel. (Kernel will fix I/0 port voltage by itself, but the
timing depends on probe order of the drivers, so the fix can
come after the camera sensor driver already failed to probe.)
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Add configurations for the Videostrong KII Pro set-top box.
This defconfig is cloned from the WeTek Play2's.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
Link: https://lore.kernel.org/r/20230507124109.31778-3-vitali64pmemail@protonmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The AD401 board is the Amlogic A1 SoC reference board
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230505125639.3605-6-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Two conflicting bootcmds were included in the environment.
Streamline to defining the bootcmd only in the env file.
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Enable the newest features: nvmxip, fwu-metadata and
gpt. Commands to print the partition info, gpt info
and fwu metadata will be available.
Adjust also env boot script the address of the
bootbank with the new gpt layout, and also remove
the not needed kernel address bank0 and bank1
and retrieve function that would test the bank flag
before and now we are getting the info from the fwu
metadata.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
We need to distinguish between boot banks and from which
partition to load the kernel+initramfs to memory.
For that, fetch the boot index, fetch the correspondent
partition, calculate the correct kernel address and
then set the env variable kernel_addr with that value.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
it is expected that the firmware that runs before
u-boot somehow provide the information of the bank
for now we will fetch the info from the metadata
since the Secure enclave is the one responsible for
this information.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
