The device tree binding provides for getting VBUS state from a device
referenced by phandle, as an optional alternative to using a GPIO. In
U-Boot, where there is no power supply class, this VBUS detection will
be implemented using a regulator device and its get_enable method.
Let's hook this up to the PHY driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Linux driver checks the VBUS detection GPIO first; then VBUS power
supply; then finally assumes VBUS is present. When adding VBUS power
supply support, we want to match that order, so we get the same behavior
in case both a GPIO and a power supply are provided in the device tree.
So refactor the function a bit to remove the early return, and use the
same "assume VBUS is present" final fallback.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Both of these messages log the GPIO number of the ID detection GPIO,
which is not terribly useful, especially in the VBUS detection function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
Subroutines in comphy_usb2_power_up() and comphy_sgmii_power_up() functions
may fail. In this case, do not continue execution of current function and
instead jump to the end. Return value in 'ret' variable is already set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
phy_txd_inv or phy_rxd_inv needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9408
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add protection on presence and order of the phy node sub node
by using the mandatory reg information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The vbus-supply is an optional property of sub-node connector node.
and no more in the usb phyc node (in first proposed binding).
This regulator for USB VBUS may be needed for host mode.
See the latest kernel binding for details in
Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml.
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
#phy-cells = <0>;
connector {
compatible = "usb-a-connector";
vbus-supply = <&vbus_sw>;
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In commit b24bb99d cp110 configuration initially done in u-boot
was removed and delegated to atf firmware as smc call.
That commit didn't account for later introduced in d13b740c SATA invert polarity support.
This patch adds support of passing SATA invert polarity flags to atf
firmware during the smc call.
Signed-off-by: Denis Odintsov <shiva@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver is needed for XHCI to work on the Allwinner H6 SoC. The
driver is copied from Linux v5.10.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
These don't belong in the drivers Makefile so move them down into
the correct place.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup some missing dependencies this exposed]
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 84a42ae366 ("dm: core: Rename device node to indicate it
is private") and commit f10643cf8a ("dm: core: Access device ofnode
through functions") accesses to the "node" member were replaced with
dev_ofnode(). Also apply that replacement here.
Fixes: 4547551aa0 ("phy: Add Amlogic AXG MIPI PCIe Analog PHY driver")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
With commit 41575d8e4c ("dm: treewide: Rename auto_alloc_size members
to be shorter") "priv_auto_alloc_size" was renamed to "priv_auto". Apply
the rename to these two drivers as well.
Fixes: 4547551aa0 ("phy: Add Amlogic AXG MIPI PCIe Analog PHY driver")
Fixes: 7ef19503ba ("phy: Add Amlogic AXG MIPI D-PHY driver")
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig) and supports resets for each of the
lanes.
This is an adaptation of the linux driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
Add a Sierra PHY driver with PCIe and USB support.
This driver is a port from the mainline linux driver.
The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.
There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself. Additionally there are
resets for each PHY lane.
The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.
The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required) for each lane
group, and then enable the PHY. Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
One difference with the linux driver is that the PHY is
always reset after it is powered-on. This is because role
switching is not supported in u-boot and the cable
orientation is handled by the PHY reset.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
The AB8500 PMIC contains an USB PHY that needs to be set up in
device or host mode to make USB work properly. Add a simple driver
for the generic PHY uclass that allows enabling it.
The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange.
The USB PHY must be configured in either host or device mode and
somehow the USB PHY driver must be made aware of the mode.
Actually, the MUSB driver used together with this PHY does not
support dynamic selection of host/device mode in U-Boot at the moment.
Therefore, one very simple approach that works fine is to select
the mode to configure at compile time. When the MUSB driver is
configured in host mode the PHY is configured in host mode, and
similarly when the MUSB driver is configured in device/gadget mode.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Recent Allwinner platforms (starting with the H3) only use the MUSB
controller for peripheral mode and use HCI for host mode. As a result,
extra steps need to be taken to properly route USB signals to one or
the other. More precisely, the following is required:
* Routing the pins to either HCI/MUSB (controlled by PHY);
* Enabling USB PHY passby in HCI mode (controlled by PMU).
The current code will enable passby for each PHY and reroute PHY0 to
MUSB, which is inconsistent and results in broken USB peripheral support.
Passby on PHY0 must only be enabled when we want to use HCI. Since
host/device mode detection is not available from the PHY code and
because U-Boot does not support changing the mode dynamically anyway,
we can just mux the controller to MUSB if it is enabled and mux it to
HCI otherwise.
This fixes USB peripheral support for platforms with PHY0 dual-route,
especially H3/H5 and V3s.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add additional step which enables the Impedance and PLL calibration.
- Enable old squelch detector instead of the new analog squelch detector
circuit and update host disconnect threshold value.
- Update LS TX driver strength coarse and fine adjustment values.
Change-Id: Ifa0a585bfb5ecab0bfa033eed6874ff98b16a7df
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
According to Design Reference Specification the PHY PLL and Calibration
register from PHY0 are shared for multi-port PHY. PLL control registers
inside other PHY channels are not used.
This commit reworks utmi device tree nodes in a way that common PHY PLL
registers are moved to main utmi node. Accordingly both child nodes
utmi-unit range is reduced and register offsets in utmi_phy.h are updated
to this change.
This fixes issues in scenarios when only utmi port1 was in use, which
resulted with lack of correct pll initialization.
Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
New products can contain up to 6 usb ports, therefore allow to initialize
all relevant UTMI PHYs.
Change-Id: I28c36e59fa0e3e338bb3ee0cee2240b923f39785
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
It helps ATF to determine who called power off
function (U-boot/Linux) and act accordingly
Change-Id: Icfc5cbfdba64754496812154272b28c0ff639f0f
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
- the default value of comphy pipe selector is set to PCIe (x4)
in case of unconnected comphy the default value remains 0x4
which may lead to several issues with comphy initialization.
- this patch adds SMC call that powers off the comphy lane in case of
unconnected comphy.
Change-Id: I196b2916518dd8df3b159ffa85e2989b8e483087
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Currently, we don't pass id for SGMII 0/1.
A bug in comphy selector configuration was found (in comphy
firmware), after fixing it, SGMII0/1 have different configuration,
so we need to pass the ID the firmware.
Change-Id: Idcff4029cc9cf018278e493221b64b33574e0d38
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Change-Id: I358792a96c13b54e700c05227cc7a8f6bd584694
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Now the comphy configuration is handled in atf, therefore there is no
need to configure phy or pipe selector in u-boot, it is configured by
atf for each particular pair: lane and mode.
Change-Id: I0bebf8d5ff66dbeb6bf9ef90876195938a8eb705
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Replace the XFI training with appropriate SMC call, so the firmware will
perform exact initialization.
Update Stefan 2021-03-23:
Move comphy_smc() function to an earlier place - necessary for the
mainline merge.
Change-Id: I789b130b05529dc80dadcf66aef407d93595b762
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Igal Liberman <igall@marvell.com>
Replace the comphy initialization for USB with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: I7f773c0dfac70db9dd2653de2cdcfac577e78c4e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Replace the comphy initialization for RXAUI with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: Iedae0285fb283e05bb263a8b4ce46e8e7451a309
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
This allows the lower level driver access to comphy map data
(required for RX training support, which is introduced
in the following patches).
Change-Id: Ib7ffdc4b32076c01c3a5d33f59552c9dfc6b12fa
Signed-off-by: Igal Liberman <igall@marvell.com>
If fdtdec_get_int can't find speed, set COMPHY_SPEED_INVALID
If fdtdec_get_int can't find type, set COMPHY_TYPE_INVALID
Move the error print if phy-type is invalid
Add continue to the probe loop (in a case of invalid phy)
Cosmetic changes
Change-Id: I0c61b40bfe685437426fe907942ed338b7845378
Signed-off-by: Igal Liberman <igall@marvell.com>
Add UTMI analog parameters initialization values according to
latest ETP.
Change-Id: I5bcca205a3995202a18ff126f371a81f69e205c8
Signed-off-by: Igal Liberman <igall@marvell.com>
UTMI should be initialized only for enabled device tree nodes.
This fix overrides current internal configuration array
entry with the next DT entry data if error is detected
during the current DT entry parsing or the current port
is disabled.
This way the internal configuration structure will only
contain valid ports information obtained from the DT.
Change-Id: I9c43c6a5d234e15ae9005d1c9bc983fc1f3544b8
Signed-off-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
In get_speed_string() we have an array (speed_strings[])
which includes all possible speed strings.
This array size and content must be aligned to the speed
defines in comphy_data.h.
This patch adds missing 5.125G speed, aligns speed_strings[]
and fixes incorrect printing when speed > 5.0G.
Change-Id: I9900d23595094be321be0c62fcaa88036324568e
Signed-off-by: Igal Liberman <igall@marvell.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
