Linux requires to describe nand structure under nand controller.
If it is not described nand device is not detected by Linux.
Error shown by Linux kernel:
pl35x-nand-controller e1000000.nand-controller: Incorrect number of NAND chips (0)
pl35x-nand-controller: probe of e1000000.nand-controller failed with error -22
When wired:
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3fcd68ccdfed5e6c079681e3b29e06583ec8a375.1695378830.git.michal.simek@amd.com
The DPSUB DT bindings now specify ports to model the connections with
the programmable logic and the DisplayPort output. Add them to the
device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1c91420e90bc823d7529834c33438216857c7161.1695378830.git.michal.simek@amd.com
Some boards are using one mdio bus which holds multiple phys and also
boards are using mdio node for bus description. That's why there are cases
where address/size-cells are unnecessary which is also reported by make W=1
dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle
it based on used description.
Error log:
/axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without
"ranges" or child "reg" property
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/02f308c774d4f2a798a9a8c066824114a19841a7.1695378830.git.michal.simek@amd.com
All zynqmp boards have been already described via mdio node that's why also
convert the rest of the boards. With using mdio node there is an option to
add reset property for the whole mdio bus which is reflected by
's/phy-reset-gpios/reset-gpios/g' for some boards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ff165281a70a38e2b76fee91e6255ce95ce8021b.1695378830.git.michal.simek@amd.com
Read the tristate config for all the pins and display it.
ZynqMP> pinmux status MIO1
MIO1: slew:fast bias:enabled pull:up input:cmos drive:12mA
volt:1.8 tri_state:enabled
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230914100620.26346-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For Xilinx ZynqMP SOC new parameter was added and now it can
set 7 parameters for its pins. Pinmux status command will
print the status of these parameters for each pin. But
current print buffer length is only 80 characters long, increase it
to 90 to print all the parameters without truncation.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230920030006.6488-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
MDC clock change needs to be done when the driver probe function
is called as mdio is enabled at probe and not when the ethernet starts.
Setup the MDC clock at the probe itself.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230922045010.22852-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
A RK8XX PMIC is typically using i2c0 on RK356x devices. Add bootph-all
to required pinctrl nodes to simplify use of the prevent booting on
power plug-in option in SPL.
With the following Kconfig options and nodes in u-boot.dtsi the prevent
booting on power plug-in option can work in SPL.
CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_PINCTRL=y
CONFIG_SPL_PMIC_RK8XX=y
&i2c0 {
bootph-pre-ram;
};
&rk817 {
bootph-pre-ram;
regulators {
bootph-pre-ram;
};
};
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 30975fb73d ("rockchip: Add option to prevent booting on
power plug-in") introduce an option to prevent booting a device when the
device was powered on due to power plug-in instead of pressing a power
button.
This feature works by checking the power-on source during PMIC probe
and powers off the device if power-on source was power plug-in.
This check currently runs very late at PMIC probe in U-Boot proper.
Fix so that the power-on source check can work at probe time in SPL.
Also enable probe after bind and remove the PMIC banner in SPL.
With this we can use ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON and
SPL_PMIC_RK8XX to power off the device very quickly after TPL instead
of after TF-A and U-Boot proper has been loaded and run.
DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB
change to: 324MHz
clk skew:0x64
change to: 528MHz
clk skew:0x58
change to: 780MHz
clk skew:0x58
change to: 1056MHz(final freq)
clk skew:0x40
out
Power Off due to plug-in event
Fixes: 30975fb73d ("rockchip: Add option to prevent booting on power plug-in")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With PMIC_RK8XX, SYSRESET and CMD_POWEROFF options enabled it is
possible to power down a board using the poweroff command and turn the
board back on using a power button.
Enable the poweroff command on RK356x boards that have a button wired
to PMIC pwron.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select SYSRESET_CMD_POWEROFF to use the sysreset implementation of the
poweroff command when PMIC_RK8XX is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Sync the device tree for RK3588 series with Linux 6.6-rc1.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Without DOS_PARTITION support U-Boot is not able to boot an OS stored
into an SD card with MBR partitions table. This is still a quite common
case so add DOS_PARTITION (only for U-Boot proper build) to Rockchip
RK3308 EVB, Radxa ROCK Pi S and Firefly roc-rk3308-cc boards: they are
the only RK boards missing of DOS_PARTITION.
Reported-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK3588 boards that
have an enabled gmac node and drop ETH_DESIGNWARE and GMAC_ROCKCHIP for
remaining RK3588 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK356x boards that
have an enabled gmac node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk_gmac_ops and other special handling that is needed for GMAC to
work on RK3588.
rk_gmac_ops was ported from linux commits:
2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based
on Synopsys DWC Ethernet QoS IP.
rk_gmac_ops was ported from linux commit:
3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove spam of RX packet not available debug messages when waiting to
receive a packet.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Return error code when phy_connect fails or no link can be established.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
rx_pkt is allocated and not used for anything, remove it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for generating a LZMA-compressed U-boot binary with the
help of binman, if CONFIG_SPL_LZMA is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for generating a GZIP-compressed U-boot binary with the
help of binman, if CONFIG_SPL_GZIP is selected.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update and improve documentation about build steps for SoCs that
require using TF-A and TPL binaries provided by Rockchip, such as
rk3308. Add rk3308 boards case to rST document. Add ROCK Pi S in
the list of supported boards. Minor page format improvements.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on rk3308 SoC using U-Boot
TPL or SPL, and therefore an external TPL binary must be used to
package a bootable u-boot-rockchip.bin image.
Default ROCKCHIP_EXTERNAL_TPL to yes if ROCKCHIP_RK3308.
Remove useless TPL_SERIAL.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Port the Rockchip IO-domain driver for RK3568 from linux.
The driver auto probe after bind to configure IO-domain based on the
regulator voltage. Compared to the linux driver this driver is not
notified about regulator voltage changes and only configure IO-domain
based on the initial voltage autoset by the regulator.
It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage
and IO-domain may end up out of sync.
Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add
rk3568 support").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The voltage value for switchout converters is always reported as 0 uV.
When the switch is enabled, it's voltage is same as input supply.
Fix this by implementing get_value for switchout converters.
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
