PLLSAIP divider uses 2 bits (bits 16 and 17) into RCC_PLLSAICFGR
register, available combination are :
00: PLLSAIP = 2
01: PLLSAIP = 4
10: PLLSAIP = 6
11: PLLSAIP = 8
Previously, the divider value was incorrectly set to 6.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
All current STM32F4 supported boards uses a 8MHz external oscillator.
All current STM32F7 supported boards uses a 25MHz external oscillator.
In order to introduce the new stm32f429-evaluation board which uses a
25MHz external oscillator without creating a dedicated struct
stm32_clk_info for this board, retrieve the external oscillator
frequency from DT and set pll_m accordingly to obtain 1MHz for the VCO.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add macros for the DIV6P1 clock type, which is used on Gen2
and optionally also on Gen3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull code which is common for RCar Gen2 and RCar Gen3 into
separate source file. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for each SoC clock table, so they can be
compiled in or out at build time. This can reduce the size of
the binary if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Gen2 requires setting RMSTPCR before booting, while on Gen3 this
is thus far always zero. Split the tables so the RMSTPCR can be set
too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Extract the macros specific to Gen3 clock into a separate header.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all SoCs have the same PLL configuration options,
so make those PLL configuraion tables per-SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all drivers use the same IDs, so make those IDs per-driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Split the massive driver into smaller per-SoC drivers and pull the
common code into a separate file. This would allow configuring out
unnecessary clock drivers once the Kconfig changes are in and also
allow adding more clock tables easily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Makefile entries in the clk driver directory were not alphabetically
sorted. Correct this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The clk uclass was converted to support a live device tree recently,
hence the global data pointer declarations are no longer needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
checkpatch.pl complains that the clk_ops structures used in clk-uclass.c
ought to be const, so we mark them as const.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Update default AXI, TUN, ARC clock set options:
instead of changing only IDIV divider settings adjust also domain PLL
settings.
Add support of TUN_ROM and TUN_PWM clocks (subclocks of TUNN_PLL)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Bind rockchip reset to clock-controller with rockchip_reset_bind().
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Fix a copy-paste typo in the clock table entry, s/7795/7796/.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add rk3128 clock driver and cru structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Differentiate the generic clock source selection value from the parent
clock index to fix the incorrect assignment of the generic clock
source selection.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To get the same behavior as the Linux driver, instead of selecting
the closest inferior rate, select the closest inferior or superior
rate
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
What the AT91_UTMI depends on SPL_DM isn't right. AT91_UTMI is not
only used in SPL, also in other place, even if SPL_DM isn't enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Now that clk_stm32f7.c manages clocks for both STM32F4 and F7 SoCs
rename it to a more generic clk_stm32f.c
Fix also some checkpatch errors/warnings.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 and STM32F7 RCC clock IP are very similar.
Same driver can be used to managed RCC clock for
these 2 SoCs.
Differences between STM32F4 and F7 will be managed using
different compatible string :
_ overdrive clock is only supported by STM32F7
_ different sys_pll_psc parameters can be used between STM32F4
and STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add a dedicated stm32f7 compatible string to use clk_stm32f7
driver with both STM32F4 and STM32F7 SoCs.
It will be needed to manage differences between these 2 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add xHCI entry into the clock tables, so that the xHCI USB driver
can enable the clock for the xHCI block via clock framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The MSTP registers were poked in boards/renesas/rcar-common/common.c
in arch_preboot_os hook thus far to shut down the clock before Linux
takes over. With DM, this is no longer needed and we can do the same
in the clock driver .remove callback. This patch adds such a .remove
callback for R8A7795 and R8A7796.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The RK3399 clk driver still has a left-over use of extract_bits, which
can be replaced by using bitfield_extract from include/bitfield.h.
This rewrites the invocation to use the shared function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using priv for new sysreset driver binding.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
