This GPIO controller device is used on UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Base addresses for GPIOs could be different for different socs, this
patch moves the base addresses from driver to the soc specific location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This patch removes the gpio clock enable from gpio driver & move it in the
board code, making it possible to use the gpio driver with other socs.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The tegra GPIO controller has two ways of reading the value of a GPIO. It
can supply the 'input' value (which is the value read from the pin) and the
'output' value (which is the value being driven from the pin. With a GPIO
set to output mode, the 'input' value is always low which is not very
useful.
This has the unfortunate result that setting a GPIO high still leaves it
showing as low in the 'gpio status' command.
Adjust the driver to check which direction the GPIO is set to, then read
the value from the appropriate register: 'input' for input GPIOs, 'output'
for output GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
At present this GPIO driver still uses the legacy PCI API. Now that
we have proper PCH drivers we can use those to obtain the information
we need. While the device tree has nodes for the GPIO peripheral it is
not in the right place. It should be on the PCI bus as a sub-peripheral
of the PCH device.
Update the device tree files to show the GPIO controller within the PCH,
so that PCI access works as expected. This also adds '#address-cells'
and '#size-cells' to the PCH node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
All boards using this driver are with device tree support,
hence drop the legacy code in driver to have a pure DT solution.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In PIC32 GPIO controller is part of PIC32 pin controller.
PIC32 has ten independently programmable ports and each with multiple pins.
Each of these pins can be configured and used as GPIO, provided they
are not in use for other peripherals.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Provide this method so that 'gpio status' works fully. It now shows
whether a pin is used for input, output or some other function.
Signed-off-by: Simon Glass <sjg@chromium.org>
For SPL we don't really need sprintf() and with tiny-printf this is not
available. Allow this to be dropped in SPL when using tiny-printf.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Override the default name_to_gpio() function with one that
accepts strings of the form bank:pin. If a colon is present
in the provided name, it behaves like the default version.
This lets the "gpio" command work with sane names rather than
requiring the user to enter the bank/pin composite in decimal.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Convert altera_pio to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM_GPIO, gpio parameters like ACTIVE_(LOW/HIGH) are to be
parsed in xlate gpio drivers-ops. Since xlate is not implemented
in omap_gpio driver, the driver considers all gpio to be
ACTIVE_HIGH which is the default case and fails to return actual
gpio status for ACTIVE_LOW gpios. So adding .xlate ops to
omap_gpio.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
After rework in lib/fdtdec.c, the function fdtdec_get_addr()
doesn't work for nodes with #size-cells property set to 0.
To get GPIO's 'reg' property, the code should use one of:
fdtdec_get_addr_size_auto_no/parent() function.
Fortunately dm core provides a function to get the property.
This commit reworks function gpio_exynos_bind(), to properly
use dev_get_addr() for GPIO device.
This prevents setting a wrong base register for Exynos GPIOs.
Tested on: Odroid U3/X2, Trats, Trats2, Odroid XU3, Snow (by Simon).
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
In order to make it clear what the parameters to set_config() and
set_direction() mean, and similarly for the return values from the
respective get_*(), define named constants for these values.
Disassembly shows no diff in the generated code, except that the
order of the code in the branches of tegra_gpio_get_function() gets
modified without affecting behaviour.
Suggested-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These enum values aren't used anywhere. Remove them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's GPIO driver currently enables pins as GPIO as soon as they're
requested. This is not safe, since the desired direction and output value
are not yet known. This could cause a glitch on the output pins between
gpio_request() and gpio_direction_*(), depending on what values happen to
be in the GPIO controller's in/out and out-value registers vs. the final
desired configuration.
To solve this, defer enabling pins as GPIOs until some gpio_direction_*()
is invoked, and the desired configuration is explicitly programmed.
In theory this change could cause regressions, if code exists that claims
a GPIO, never explicitly sets a direction, and then gets/sets the GPIO
value based on that assumption. However, I've read through all the Tegra-
related board files and device drivers that touch GPIOs and I do not see
such buggy code anywhere.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's gpio_config_table() currently uses common GPIO APIs. These used
to work without requesting the GPIO, but since commit 2fccd2d96b "tegra:
Convert tegra GPIO driver to use driver model" no longer do so. This
prevents any of the GPIO initialization table from being applied to HW.
Fix gpio_config_table() to directly program the HW to solve this.
Fixes: 2fccd2d96b ("tegra: Convert tegra GPIO driver to use driver model")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The current simplify lpc32xx gpio driver implementation assume a
maximum of 32 GPIO per port; there are a total of 22 GPI, 24 GPO
and 6 GPIO to managed on port 3.
Update the driver to fix the following:
1) When requesting GPI_xx and GPO_xx on port 3 (xx is the same number)
the second call to "gpio_request" will return -EBUSY.
2) The status of GPO_xx pin report the status of the
corresponding GPI_xx pin when using the "gpio status" command.
3) The gpio driver may setup the direction register for the wrong
gpio when calling "gpio_direction_input" (GPI_xx) or
"gpio_direction_output" (GPO_xx) on port 3; the call to the
direction is require to use the "gpio status" command.
The following change were done in the driver:
1) port3 GPI are cache in a separate 32 bits in the array.
2) port3 direction register written only for GPIO pins.
3) port3 GPO & GPIO (as output) are read using "p3_outp_state".
4) LPC32XX_GPI_P3_GRP updated to match the change.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
* Add mxc_gpio support for imx7d SoC
* Use CONFIG_MX7 to extend mxc gpio driver support for imx7d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Fix gpio_read: gpio input (INDT) and gpio output (OUTDT) registers
have different offset. gpio_read must be performed from INDT.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This function can return an error. Correct the detection of this error so
that it works even with large 32-bit addresses.
The return value is set up for returning an I/O address but the function is
also used to return a memory-mapped address. Adjust the return code to make
this work.
Also add a bit more debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
These calls seem to be incorrect. The function expects an I/O address but
the existing callers pass the value at an I/O address. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver for the DesignWare APB GPIO IP block.
This driver is DM capable and probes from DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
sun6i and later have a couple of io-blocks which are shared between the
main CPU core and the "R" cpu which is small embedded cpu which can be
active while the main system is suspended.
These gpio banks sit at a different mmio address then the normal banks,
and have a separate devicetree node and compatible, this adds support for
these banks to the sunxi-gpio code when built with device-model support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since a gpio_desc is allowed to be invalid we should return an error
indicating that the operation cannot be completed. This can happen if the
GPIO is optional - e.g. some devices may have a reset line and some may
not.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be used for testing to manually request a GPIO for use,
without resorting to the legacy GPIO API.
Signed-off-by: Simon Glass <sjg@chromium.org>
The LPC32XX GPIO driver platdata currently contains GPIO state information,
which should go into priv_data. Thus rename lpc32xx_gpio_platdata to
lpc32xx_gpio_priv and convert to use dev_get_priv() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
Like SPI and I2C few GPIO controllers also have
multiple chip instances. This patch adds the
flag 'DM_UC_FLAG_SEQ_ALIAS' in gpio_uclass driver
to control device sequence numbering. By defalut
the dev->r_seq for gpio_uclass will alwalys
returns -1, which leads the gpio driver probe
failure when using the driver with device trees.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Add "allwinner,sun8i-a33-pinctrl", this is used by the latest upstream
linux sunxi dts files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
gpio_get_values_as_int() should return an error if something goes wrong.
Also provide gpio_claim_vector(), a function to request the GPIOs and set
them to input mode. Otherwise callers have to do this themselves.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The GPIO driver didn't correctly compute the bank offset
from the GPIO number and caused random writes into the
GPIO block address space. Fix the driver so it actually
does the writes correctly. While at it, make use of the
clrsetbits_le32() mechanisms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that all sunxi boards are using driver-model for gpio (*), we can remove
the non driver-model support from the axp gpio code, and the glue to call
into the axp gpio code from the sunxi_gpio non driver-model code.
*) For the regular u-boot build, SPL still uses non driver-model gpio for
now, but the SPL never uses axp gpios support and we were already not building
axp-gpio support for the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add driver-model support to the axp_gpio code, note that this needs a small
tweak to the driver-model version of sunxi_name_to_gpio to deal with the
vbus detect and enable pins which are not standard numbered gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.
This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.
Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.
The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change the axp_gpio_foo function prototypes to match the gpio uclass op
prototypes, this is a preparation patch for moving the axp gpio code to
a separate driver-model gpio driver.
Note that the ugly calls with a NULL udev pointer in drivers/gpio/sunxi_gpio.c
this adds are removed in a later patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When doing a driver-model enabled build we still need sunxi_name_to_gpio_bank
(for now) for the mmc pinmux code in board/sunxi/board.c, so build it for
driver-model enabled builds too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We want to use driver-model/fdt with other model SoCs too, so add
compatible strings for the other SoCs to the dm sunxi gpio code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Until sunxi moves to device tree (e.g. for USB) we need to convert named
GPIOs to numbers. Add a function to do this.
This fixes the USB / EHCI support not working on the LinkSprite pcDuino3
(which uses devicemodel).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
By convention, sunxi GPIOs are named PA1, PA2 instead of A1, A2. Change
the driver model GPIO driver for sunxi to use these names.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Most of the code is taken (and adapted) from Linux kernel driver.
Just add CONFIG_ZYNQ_GPIO to you config to enable it
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Marvell GPIO driver can be used on Marvell platforms other than
Sheeva, so remove the ifdef to enable it for others.
Signed-off-by: Rob Herring <robh@kernel.org>
1. The bits 11..10 for mfp driver strength is only valid for
aspen and old xscale family, for newer Marvell chip, this range
has been moved to 12..11.
2. add sleep bit support
Signed-off-by: Xiang Wang <wangx@marvell.com>
[robh: rebase to current mainline]
Signed-off-by: Rob Herring <robh@kernel.org>
This has a prototype but no implementation. It returns the global GPIO number
given a gpio_desc. It is useful for debugging in some cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The function gpio_request_list_by_name_nodev() returned -ENOSPC error,
when the loop count was greater than requested count. This was wrong,
because function should return the requested gpio count, when meets
the call request without errors. Now, the loop ends on requested
max_count.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions currently use a generic name, but they are for x86 only.
This may introduce confusion and prevents U-Boot from using these names
more widely.
In fact it should be possible to remove these at some point and use
generic functions, but for now, rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.
This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Use the full driver model GPIO and serial drivers in SPL now that these are
supported. Since device tree is not available they will use platform data.
Remove the special SPL GPIO function as it is no longer needed.
This is all in one commit to maintain bisectability.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch add DT support for mxc gpio driver.
There are one place using CONFIG_OF_CONTROL macro.
1. The U_BOOT_DEVICES and mxc_plat array are complied out. To DT,
platdata is alloced using calloc, so there is no need to use mxc_plat.
The following situations are tested, and all work fine:
1. with DM, without DT
2. with DM and DT
3. without DM
Since device tree has not been upstreamed, if want to test this patch.
The followings need to be done.
+ pieces of code does not gpio_request when using gpio_direction_xxx and
etc, need to request gpio.
+ move the gpio settings from board_early_init_f to board_init
+ define CONFIG_DM ,CONFIG_DM_GPIO and CONFIG_OF_CONTROL
+ Add device tree file and do related configuration in
`make ARCH=arm menuconfig`
These will be done in future patches by step.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
Add a new entry in platdata structure and intialize
bank_index in mxc_plat array.
This new entry can avoid using `plat - mxc_plat` by using
`plat->bank_index`.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Use dev_get_priv() rather than dev_get_platdata() to get correct address of
private data.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
This deals with the polarity bit. It also changes the GPIO devices so that
the correct device tree node is linked to each one. This allows us to use
the new uclass phandle functionality to implement a proper GPIO binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present U-Boot sort-of supports the standard way of reading GPIOs from
device tree nodes, but the support is incomplete, a bit clunky and only
works for GPIO bindings where #gpio-cells is 2.
Add new functions to request GPIOs, taking full account of the device
tree binding. These permit requesting a GPIO with a simple call like:
gpio_request_by_name(dev, "cd-gpios", 0, &desc, GPIOD_IS_IN);
This will request the GPIO, looking at the device's node which might be
this, for example:
cd-gpios = <&gpio TEGRA_GPIO(B, 3) GPIO_ACTIVE_LOW>;
The GPIO will be set to input mode in this case and polarity will be
honoured by the GPIO calls.
It is also possible to request and free a list of GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Only the GPIO driver knows about the full GPIO device tree binding used by
a device. Add a method to allow the driver to provide this information to the
uclass, including the GPIO offset within the device and flags such as the
polarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far driver model's GPIO uclass just implements the existing GPIO API.
This has some limitations:
- it requires manual device tree munging to support GPIOs in device tree
(fdtdec_get_gpio() and friends)
- it does not understand polarity
- it is somewhat slower since we must scan for the GPIO device each time
- Global GPIO numbering can change if other GPIO drivers are probed
- it requires extra steps to set the GPIO direction and value
The new functions have a dm_ prefix where necessary to avoid name conflicts
but we can remove that when it is no-longer needed. The new struct gpio_desc
holds all required information about the GPIO. For now this is intended to
be stored by the client requesting the GPIO, but in future it might be
brought into the uclass in some way.
With these changes the old GPIO API still works, and uses the driver model
API underneath.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It does not make sense to make gpio_direction_input() return the gpio input
status. The return value of gpio_direction_input() is inconsistent if
CONFIG_DM_GPIO is defined.
And we don't need to call gpio_direction_input() int sunxi_mmc_getcd().
Just init the gpio once in mmc_resource_init() is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.
Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Current code does not set gpio output value in ich6_gpio_direction_output(),
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
Modify this driver to support driver model, with platform data required to
determine the GPIOs that it controls.
Signed-off-by: Simon Glass <sjg@chromium.org>
When not relying on Coreboot for GPIO init the GPIOs must be set up
correctly. This is currently done statically through a rather ugly method.
As the GPIOs are figured out they can be moved to the device tree and set
up as needed rather than all at the start.
In this implementation, board files should call ich_gpio_set_gpio_map()
before the GPIO driver is used in order to provide the GPIO information.
We use the early PCI interface so that this driver can now be used before
relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For board IDs a common approach is to set aside several GPIOs for use in
determining the board ID. This can provide information about board features
and the revision.
Add a function that turns a list of GPIOs into an integer by assigning
each GPIO to a single bit.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Convert over this driver, using device tree to pass in the required
information. The peripheral is still probed, just the number of GPIO banks
and their offsets is in the device tree (previously this was a table in
the driver).
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the uclass supports gpio_request/free() there is no need for the
driver to implement it too. Drop this unnecessary code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement this method so that the 'gpio' command can do its job correctly.
For sandbox we only support input and output states for a gpio.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have several GPIO drivers now and all are doing similar things to record
which GPIOs are reserved.
Move this logic into the uclass to make the drivers similar.
We retain the request()/free() methods since currently one driver does use
these for setting up the pin.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model support to this driver, while retaining support for the
legacy system. Driver model GPIO support is enabled with CONFIG_DM_GPIO
as usual.
Since gpio_is_valid() no longer exists, we can use the -EINVAL error
returned from gpio_request().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add a separate internal helper function to get a GPIO value, so that we
will be able to call it with the driver model version and avoid code
duplication.
Also move gpio_get_bank() and check_gpio() down below the helper functions
as these won't be needed with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
At present banks must be named and it is not possible to refer to GPIOs by
number in driver model. Some boards use numbering - e.g. OMAP. It is fairly
easy to support by detecting the absense of a bank name (which starts with
a letter).
Add support for numbered GPIOs in addition to the existing bank support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Convert the BCM2835 GPIO driver to use driver model, and switch over
Raspberry Pi to use this, since it is the only board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Add driver model support with this driver. In this case the platform data
is in the driver. It would be better to put this into an SOC-specific file,
but this is best attempted when more boards are moved over to use driver
model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Convert the exynos GPIO driver to driver model. This implements the generic
GPIO interface but not the extra Exynos-specific functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
The defines at the top of the GPIO driver use single-character names for
parameters which are not very descriptive.
Improve these to use descriptive parameter names.
Signed-off-by: Simon Glass <sjg@chromium.org>
The wrong header is being included, thus requiring the code to re-declare
the generic GPIO interface in each GPIO header.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix Tegra GPIO driver to not crash resp. misbehave upon requesting
GPIOs with an empty aka NULL label. As the driver uses exclusively the
label to check for reservation status actually supplying one is
mandatory!
This fixes a regression introduced by commit:
2fccd2d96b
tegra: Convert tegra GPIO driver to use driver model
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.
The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.
The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.
Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
In current gpio_set_value() implementation, it always sets the gpio control bit
no matter the value argument is 0 or 1. Thus the GPIOs never set to low.
This patch fixes this bug.
The address bus is used as a mask on read/write operations, so that independent
software drivers can set their GPIO bits without affecting any other pins in a
single write operation. Thus we don't need a read-modify-write to update the
register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
We want 'N0' and 'n0' to mean the same thing, so ensure that case is not
considered when naming GPIO banks.
Signed-off-by: Simon Glass <sjg@chromium.org>
using UBI and DM together leads in compiler error, as
both define a "struct device", so rename "struct device"
in include/dm/device.h to "struct udevice", as we use
linux code (MTD/UBI/UBIFS some USB code,...) and cannot
change the linux "struct device"
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
We need check the NULL pointer as at91_pio_get_port() may return NULL.
Also print a error message when at91_pio_get_port() failed otherwise we
cannot notice the failure.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. Add a feature to the GPIO driver
which executes a GPIO configuration table. Board files will use this to
implement the correct HW initialization procedure.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add driver model support for GPIOs. Since existing GPIO drivers do not use
driver model, this feature must be enabled by CONFIG_DM_GPIO. After all
GPO drivers are converted over we can perhaps remove this config.
Tests are provided for the sandbox implementation, and are a sufficient
sanity check for basic operation.
The GPIO uclass understands the concept of named banks of GPIOs, with each
GPIO device providing a single bank. Within each bank the GPIOs are numbered
using an offset from 0 to n-1. For example a bank named 'b' with 20
offsets will provide GPIOs named b0 to b19.
Anonymous GPIO banks are also supported, and are just numbered without any
prefix.
Each time a GPIO driver is added to the uclass, the GPIOs are renumbered
accordinging, so there is always a global GPIO numbering order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
Add support for the Kona GPIO controller found on Broadcom mobile SoCs.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.
Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
