Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.0
This will enable USB on Amlogic Meson GXL Boards like Khadas VIM, P212 or
LibreTech-CC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The lowlevel_init function uses r4 and r6 without preserving their
values as required by the AAPCS. Use r0 and r2 instead as these
are call-clobbered.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Since commit 0e373c0ade ("spl: add SPL_RESET_SUPPORT"),
reset is supported in SPL, enable this flag for STM32F SoCs family.
This allows to remove a specific case in RCC mfd driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The mach/config.h file would helpfully define CONFIG_SYS_I2C and
CONFIG_SYS_I2C_MVTWSI if CONFIG_CMD_I2C was defined by the board. This
conflicts with the way DM_I2C works. As a transitional measure don't
automatically define these if CONFIG_DM_I2C is defined. It should be
possible to remove this once all kirkwood boards are migrated to DM.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch shows how to enable driver model support for the LS-CHLv2 and
LS-XHL boards.
There are a couple of open questions:
- do I need the u-boot,dm-pre-reloc tags in the device tree?
- should mach/config.h define CONFIG_DM_SEQ_ALIAS?
- how can we split this patch or are there any other pending patches
which does the same and I didn't catch these.
This patch is based on the http://git.denx.de/u-boot-marvell.git (master
branch) and needs the following patches, which are still pending:
https://patchwork.ozlabs.org/patch/909618/https://patchwork.ozlabs.org/patch/909617/https://patchwork.ozlabs.org/patch/909973/
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Some QCA988x based modules presence is not detected by the SERDES lanes,
so force this detection which will trigger the LTSSM state machine to
negotiate link.
An example of such a card is WLE900VX.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot,dm-pre-reloc was missing from pinctrl and it's
children node. causing failure to configure pin mux
before relocation.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
This undocumented function relies on arch-specific code to declare a nop
weak version. Add the weak function in common code instead to avoid having
to duplicate the same function in each arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI loader code requires certain linker sections to exist. Add these
for sandbox so that the EFI loader code will link.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add an implementation of setjmp() and longjmp() which rely on the
underlying host C library. Since we cannot know how large the jump buffer
needs to be, pick something that should be suitable and check it at
runtime. At present we need access to the underlying struct as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch implements the function unaligned_access() to reset the aligned
access flag in the system control register (SCTLR). It is called when the
bootefi command is invoked.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix SPDX identifier]
Signed-off-by: Alexander Graf <agraf@suse.de>
The efi selftest and the hello application require CRT0 and RELOC to be
built.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Variables EFI_RELOC and EFI_CRT0 have to be defined to build the
EFI unit tests. This patch ensures this for the x86 architecure.
If we compile with EFI_STUB, the bitness depends on CONFIG_EFI_STUB_64BIT.
Otherwise the bitness depends on CONFIG_X86_64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support for loading secure bitstreams on ZynqMP
platforms. The secure bitstream images has to be generated using
Xilinx bootgen tool.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import the R8A77990 and Ebisu DTS from linux-next to get the latest
version. This makes AVB ethernet work in U-Boot since the ethernet
node is now present in DT, as well as GPIOs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Basic support for the Renesas Ebisu board based on R-Car E3:
- Memory,
- Main crystal,
- Serial console,
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds basic support for the Renesas R-Car E3 (R8A77990) SoC:
- PSCI
- CPU (single)
- Cache controller
- Main clocks and controller
- Interrupt controller
- Timer
- PMU
- Reset controller
- Product register
- System controller
- UART for console
Inspried by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add ID and Kconfig entry for the Renesas R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Here we do a couple of minor fixes like:
- Move .ivt section to the very beginning of the image
by default which allows us to use that image put right
at reset vector (usually 0x0)
- Improve relocation fix-up which became required once
we moved .ivt and understood a problem with existing implementation
where we relied on a particular placement of sections.
Now we don't care about placement because we just explicitly
check for .text and in case of ARCompact .ivt sections
- Re-implemnt do_reset() such that it calls reset_cpu() which
could implmented for a particular board
And hte most important part we introduce support for yet another
devboard from Synopsys - EMDK.
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is
an FPGA-based development platform from Synopsys aimed to speed-up
development of software for ARC EM cores and entire subsystems based on
ARC EM like Data Fusion, Secure and Sensor & Control subsystems.
U-Boot is supposed to be used as a primary bootloader on EMDK allowing
users to easily load and start their application from micro-SD card.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This will allow for board-specific implementation of reset.
Default version will just stop execution with help of BRK instruction.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
For quite some time we have a GCC's built-in which inserts BRK
instruction so let's use it instead of simple insertion of in-line
assembly.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This is useful for cases when U-Boot image is put in ROM and
reset vector points to 0 where the very beginnign of the image reside.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to have the one and only linker script for all ARC boards
and so we relied on a particular order of symbols there.
Because of that we used __ivt_end as the marker of the end of all the
code which won't be true any longer if we move .ivt section to any other
place. That said we'd better check for each section separately.
A couple of other improvements:
1. There's no point to include the marker of section end in interested
range because its address is beyond the section, i.e. we should
compare with "<" but not "<=".
2. .ivt section for ARCv2 cores is just an array of 32-bit ints and
they are not swapped even on little-endia cores while in case of
ARCompact cores .ivt contains valid code so swapping is required.
3. Just in case add check for ARC600 which is also ARCompact
and its .ivt is normal code.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't care much about I$ line length really as there're
no per-line ops on I$ instead we only do full invalidation of it
on occasion of relocation and right before jumping to the OS.
Also as compared to Linux kernel where we don't support different
lengths of I$ and D$ lines in U-Boot we have to deal with such an
exotic configs if the target board is not supposed to run Linux kernel.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
After importing v4.17-rc1 Linux commit 9130ba884640 ("scripts/dtc:
Update to upstream version v1.4.6-9-gaadd0b65c987"), sandbox build
reports below warnings:
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Silent them by applying the 's/_/-/' substitution in the names of the
'fdt_dummy0', 'fdt_dummy1', 'fdt_dummy2', 'fdt_dummy3' properties.
Similar DTC warnings have been recently fixed in Linux kernel, e.g. via
v4.17-rc1 commit d366c30d19f4 ("ARM: dts: STi: Fix aliases property name
for STi boards").
If done alone, the DTS update generates a failure of the
`ut dm fdt_translation` unit test in sandbox environment as seen below:
$ ./u-boot -d arch/sandbox/dts/test.dtb
---<-snip->---
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
test/dm/test-fdt.c:444, dm_test_fdt_translation(): 0 == uclass_find_device_by_seq(UCLASS_TEST_DUMMY, 0, 1, &dev): Expected 0, got -19
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
test/dm/test-fdt.c:444, dm_test_fdt_translation(): 0 == uclass_find_device_by_seq(UCLASS_TEST_DUMMY, 0, 1, &dev): Expected 0, got -19
Failures: 2
---<-snip->---
Fix this issue in place, by updating the "name" string in the
UCLASS_DRIVER(fdt_dummy) definition, so that it matches the newly
updated aliases properties. After that, the test passes:
$ ./u-boot -d arch/sandbox/dts/test.dtb
---<-snip->---
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
---<-snip->---
Fixes: e8d5291824 ("core: ofnode: Fix translation for #size-cells == 0")
Reported-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PS clock(LPD_APB_CLK) is default clock for TTC. Add this clock
entry in TTC nodes.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Card detect bit was broken on revA and it is working fine with revC
board that's why this property can be removed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is control board on Bitmain Antminer S9.
There are 3 board variables with 256MB, 512MB and 1024MB DDR.
DDR memory is automatically detected with using get_with using
get_ram_size().
Bitmain is using 16MB space for FPGA which is handled via
reserved-memory. Also U-Boot is allocating 16B for storing bootcounts.
Watchdog is started but never service in U-Boot.
SPL MMC is working. SPL NAND is not working because it is not supported
as of now.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
