Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH is defined in the socfpga_common.h,
but not referenced at all. Remove.
Also, clean-up the README.socfpga. CONFIG_MMC should not be defined
in the header since it was moved to Kconfig by commit c27269953b
("mmc: complete unfinished move of CONFIG_MMC"). I see no grep hit
for the others.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Do the same change which was done in ZynqMP by:
"ARM64: zynqmp: Remove CONFIG_BOOTP_SERVERIP"
(sha1: a8b6a156c0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to save environment as a file of FAT filesystem
on to SD card. The file will be saved with name uEnv.txt.
This environment will be retrieved during boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Increase environment size to 32K as the current default
environment itself is greater than 4K.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since usb ether gadget have support for driver model, so enable
usb ether gadget.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL load address changes based on boot type in HS devices,
ISW_ENTRY_ADDR is used to set this address for AM43xx based SoCs
for similar reasons. Add this same logic for AM33xx devices.
Also make the default value for ISW_ENTRY_ADDR correct for GP
devices based on SoC, HS devices already pick the correct
value in their defconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Use TARGET_T1024RDB from Kconfig instead.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Get missing hunk in board/freescale/t102xrdb/ddr.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that the SPL is ready to be compiled in AArch64 and the DRAM
init code is ready, enable SPL support for the A64 SoC and in the
Pine64 defconfig.
For now we keep the boot0 header in the U-Boot proper, as this allows
to still use boot0 as an SPL replacement without hurting the SPL use
case.
We disable FEL support for now by making its compilation conditional
and disabling it for ARM64, as the code isn't ready yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The predominantely 32-bit ARM targets try to compile the SPL in Thumb
mode to reduce code size.
The 64-bit AArch64 instruction set does not know an alternative, concise
encoding, so the Thumb build option should only be set for 32-bit
targets.
Likewise -marm machine options are only valid for ARMv7 targets.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add FIT image booting from MMC device, during MMC bootcmd
u-boot env script look for bootscript, else fit image or else
finally look for legacy image uImage.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling FIT along with Signature will make bootm to
not-understanding u-boot legacy image formats like uImage, etc.
So this patch enabling legacy image format for backward compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable Flattened Image Tree support for all Engicam boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add config options for booting Linux from NAND in UBI format.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
gpmi-nand is the proper name used in nand driver from Linux for all
imx related nand boards, so rename mtdparts name as gpmi-nand instead
of nand, this will eventually reflects all nand info to Linux from
u-boot like mtdparts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Linux with uImage instead of zImage, so update
bootz with bootm.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Increase the nand kernel partition size, for supporting
large uImage files, maximum 8MiB.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add MAC support.
Use PHY, connected to RGMII1 as a default Eth adapter,
by appropriate setting of 'cpsw_data.active_slave'.
'cpsw_phy' env variable can override this setting.
Set the MAC addresses in the U-Boot environment.
The addresses are retrieved from the on-board EEPROM or from the SOC's
MAC fuses.
Set the following PHYs RGMII clock delays:
- Enable RX delay
- Disable TX delay
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: add RGMII clock delays]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
