Fetch the device class into usb device's dwcriptors,
so that the host controller's driver can use this info
to differentiate between HUB and DEVICE.
Signed-off-by: Amar <amarendra.xt@samsung.com>
XHCI ports are powered on after a H/W reset, however
EHCI ports are not. So disabling and re-enabling power
on all ports invariably.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Some cleanup in usb framework, nothing much on feature side.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
USB_PRINTF, USB_HUB_PRINTF, USB_STOR_PRINTF, USB_KBD_PRINTF
are nothing but conditional debug prints, depending on DEBUG.
So better remove them and use debug() simply.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
This commit allows pxa2xx based boards to reimplement reset_cpu()
function with board specific reset sequence.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
This patch adds a driver for the diskonchip G4 nand flash device. It is based
on the driver from the linux kernel.
This also includes a separate SPL driver. A separate SPL driver is used because
the device operates in a different mode (reliable mode) when loading a boot
image, and also because the storage format of the boot image is different from
normal data (pages are stored redundantly). The SPL driver basically mimics how
a typical IPL reads data from the device. The special operating mode and
storage format are used to compensate for the fact that the IPL does not contain
the BCH ecc decoding algorithm (due to size constraints). Although the u-boot
SPL *could* use ecc, it operates like an IPL for the sake of simplicity and
uniformity, since the IPL and SPL share the task of loading the u-boot image.
As a side benefit, the SPL driver is very small.
[port from linux kernel 3.4 commit 570469f3bde7f71cc1ece07a18d54a05b6a8775d]
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
If CONFIG_USB_DEV_PULLUP_GPIO is defined, a link error occurs because the
set_GPIO_mode() helper function is not implemented. This function doesn't do
much except make the code a little more readable, so I just manually coded its
equivalent and removed the prototype from the header file. It is invoked no
where else in the code.
While I was at it, I noticed that two other function prototypes in the same
header file are also neither implemented nor invoked anywhere, so I removed them
as well.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Make lcd_init() a weak pointer so that boards can overload it if necessary. The
palmtreo680 board needs to wiggle some gpios and configure the pwm controller in
order to get the lcd and its backlight working.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
This patch adds the bitrev library from the linux kernel. This is a simple
algorithm that uses an 8 bit look-up table to reverse the bits in data types of
8, 16, or 32 bit widths. The docg4 nand flash driver uses it.
[port from linux kernel v3.9 commit 7ee32a6d30d1c8a3b7a07a6269da8f0a08662927]
[originally added: v2.6.20 by commit a5cfc1ec58a07074dacb6aa8c79eff864c966d12]
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
There is no change of behavior, except for the folloing line that has been
removed because the iomux mode was not set accordingly and the pad used for OTG
OC is not this one:
mxc_iomux_set_input(MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, 1);
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX53. The content of the file is taken from Freescale's Linux kernel at
commit 4ab3715, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Matt Sealey <matt@genesi-usa.com>
There is no change of behavior, except for older silicon revisions for which
support is removed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add missing definitions that are required by future changes.
By the way, make some cosmetic cleanup.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
In ALT1 mode, EIM_CS2 is GPIO2[27], not ESDHC1.CD. Hence, rename
MX51_PAD_EIM_CS2__SD1_CD to MX51_PAD_EIM_CS2__GPIO2_27.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not
ALT1 (which even corresponds to nothing).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX35. The content of the file is taken from Linux kernel at commit
267dd34, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
There is no change of behavior, even if some pad control values could probably
be simplified.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for
the i.MX25. The content of the file is taken from Linux kernel at commit
267dd34, plus the required changes to make it work in U-Boot.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add basic support for the DENX M53EVK board. Currently supported is:
MMC (incl. booting)
NAND (incl. booting)
Ethernet, I2C, USB, SATA, RTC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Augment the MX5 clock code with function to enable and configure
NFC clock. This is necessary to get NFC working on MX5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Fix minor adjustments needed to get SPL framework building on MX5.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
The U-Boot SPL can parse the uImage format and gather information from
it about the payload. Make use of this and wrap u-boot.bin into uImage
format. The benefit is the SPL will know the size of the payload
instead of using fixed size of the payload defined at compile time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Add support for generic NAND SPL via the SPL framework into the
mxc_nand_spl driver. This is basically just a simple rename and
publication of the already implemented functions. To avoid the
bare-bones functions getting in the way of the NAND_SPL, build
them only if CONFIG_SPL_FRAMEWORK is not defined.
Also make sure the requested payload is aligned to full pages,
otherwise this simple driver fails to load the last page.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The MX53 ROM loads the data from NAND in multiples of pages and
supports maximum page size of 4k. Thus, align the image and header
to 4k to be safe from ROM bugs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
FSL bootlets code set the PORT_PRIORITY_ORDER field of register HW_EMI_CTRL
as 0x2, which means:
PORT0231 = 0x02 Priority Order: AXI0, AHB2, AHB3, AHB1
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
HW_DRAM_CTL27, HW_DRAM_CTL28 and HW_DRAM_CTL35 are not initialized as per
FSL bootlets code.
mx23 Reference Manual mark HW_DRAM_CTL27 and HW_DRAM_CTL28 as "reserved".
HW_DRAM_CTL8 is setup as the last element.
So skip the initialization of these DRAM_CTL registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx23 there is no 'DRAM init complete' in register HW_DRAM_CTL18.
Remove this erroneous setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
