This patch adds the groundwork for generating signed BootStream, which
can be used by the HAB library in i.MX28. We are adding a new target,
u-boot-signed.sb , since the process for generating regular non-signed
BootStream is much easier. Moreover, the signed bootstream depends on
external _proprietary_ _binary-only_ tool from Freescale called 'cst',
which is available only under NDA.
To make things even uglier, the CST or HAB mandates a kind-of circular
dependency. The problem is, unlike the regular IVT, which is generated
by mxsimage, the IVT for signed boot must be generated by hand here due
to special demands of the CST. The U-Boot binary (or SPL binary) and IVT
are then signed by the CST as a one block. But here is the problem. The
size of the entire image (U-Boot, IVT, CST blocks) must be appended at
the end of IVT. But the size of the entire image is not known until the
CST has finished signing the U-Boot and IVT. We solve this by expecting
the CST block to be always 3904B (which it is in case two files, U-Boot
and the hand-made IVT, are signed in the CST block).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.
As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.
Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Allow the boot of a device tree mainline kernel by aligning the environment
variables with other FSL boards.
Tested NFS boot of a dt 3.14-rc5 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Gateworks Ventana is a product family based on the i.MX6. This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a prototype for board_video_skip() in order to fix the following sparse
warning:
wandboard.c:227:5: warning: symbol 'board_video_skip' was not declared. Should it be static?
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Include <input.h> in order to fix the following sparse warning:
wandboard.c:278:5: warning: symbol 'overwrite_console' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a prototype for board_phy_config() to fix the following sparse warning:
wandboard.c:200:5: warning: symbol 'board_phy_config' was not declared. Should it be static?
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes the following sparse warning:
wandboard.c:137:5: warning: symbol 'board_mmc_init' was not declared. Should it be static?
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix the following sparse warning:
wandboard.c:58:22: warning: symbol 'usdhc1_pads' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since the switch may be re-configured for VLAN usage in Linux (or any
other OS), lets reset the switch to its default register values upon
power-up. Otherwise network might not be available in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
The bit DDR3_RST_DEF_VAL inside CTRL_DDR_IO represents the default value
of the ddr reset value for DDR3 before the EMIF takes over. We must have
this bit set high so that on exit from DeepSleep0 within the kernel the
reset line has the proper value.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The register secure_emif_sdram_config in control module is copied to
the EMIF sdram_config register when it is coming out of DeepSleep0 in
order to ensure that the EMIF comes up for the correct type of DDR.
Without this, resume can hang from within the kernel.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Per a suggestion from the hardware team, program the emif_pwr_mgmt_ctrl
and emif_pwr_mgmt_ctrl_shdw registers within the EMIF to hold the
desired delay in cycles that the EMIF waits without an access to enter
self-refresh, in this case 8192 cycles. With this, code desiring to
enter self refresh only has to toggle one bit to enable it.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Updating EMIF_PHY_CTRL and adding EMIF_READ_WRITE_EXECUTION_THRESHOLD
registers.
In EMIF_PHY_CTRL:
Updating [4:0]READ_LATENCY to 8, because at higher frequencies like
400MHz the read latency expected will be CL+3 as per tests from HW
folks.
Clearing [19]PHY_DIS_CALIB_RST bit as this is used onl for debug
purpose. With out this resume is not working(Still waiting for PHY team
to come back for better explanation).
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also correct the bit masking of mac id read from the efuse.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
When we tell the compiler to optimize for ARMv7 (and ARMv6 for that
matter) it assumes a default of SCTRL.A being cleared and unaligned
accesses being allowed and fast at the hardware level. We set this bit
and must pass along -mno-unaligned-access so that the compiler will
still breakdown accesses and not trigger a data abort.
To better help understand the requirements of the project with respect
to unaligned memory access, the
Documentation/unaligned-memory-access.txt file has been added as
doc/README.unaligned-memory-access.txt and is taken from the v3.14-rc1
tag of the kernel.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@ti.com>
While there are valid reasons to use __packed, often the answer is that
you should be doing something else here instead.
Signed-off-by: Tom Rini <trini@ti.com>
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This prevents references to _end from generating absolute
relocation records.
This change is binary invariant for ARM targets.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Newly added cm_t335 was missed in commit 47ed5dd0 which
made ARM targets produce full ELF files. Fix its linker
script.
This change is binary-invariant when only .dynsym, .dynstr,
.dynamic, .plt, .interp and .gun sections are declared.
Sections .hash, .got.plt, .dynbss and .ARM.exidx are also
declared so that their (unused) content is moved out of the
u-boot binary.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This reverts commit fc0fc50f38.
The author has asked on the mailing list that we revert this for now as
it breaks write support.
Reported-by: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
arch/arm/cpu/armv7/omap-common/config.mk is never included
because "omap-common" is not SoC name.
If we want to add OMAP-specific compiler flags,
they must be added to omap3/config.mk, omap4/config.mk, omap5/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Same as the previous commit.
Move sanity check to prepare1 target to avoid nasty troubles.
Before this commit, LDSCRIPT existence was not checked
when it was specified by CONFIG_SYS_LDSCRIPT.
Now LDSCRIPT existence is checked for all boards.
$(wildcard $(LDSCRIPT)) must point to the linker scripts
with absolute path.
Otherwise, make will terminate with a false error
on out-of-tree build.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Before this commit, make terminated with an error
where is shouldn't under some condition.
This bug happened when we built a board unsupporting
generic board right after building with generic board.
For example, the following sequence failed.
(harmony uses generic board but microblaze-generic does not
support it)
$ make harmony_config
Configuring for harmony board...
$ make CROSS_COMPILE=arm-linux-gnueabi-
[ Build succeed ]
$ make microblaze-generic_config
Configuring for microblaze-generic board...
$ make CROSS_COMPILE=microblaze-linux-
Makefile:488: *** Your architecture does not support generic board.
Please undefined CONFIG_SYS_GENERIC_BOARD in your board config file. Stop.
We had to do "make clean" before building the microblaze board.
This commit fixes this unconvenience.
Move generic board sanity check to "prepare1" target,
which is run after generation of include/autoconf.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 6ab6b2af deleted ./u-boot.dtb because it was a copy
of dts/dt.dtb.
But Simon suggested to keep u-boot.dtb at the top directory
because it is a build output.
After discussions, we agreed on revival of ./u-boot.dtb.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
"help" target has been copied from Linux 3.13 and adjusted
for U-Boot.
Unlike Linux, cleaning is done on 4 levels:
clean, clobber, mrproper, distclean.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit avoids generating ./SPL twice.
- Fist time descending to spl/
- Second time as a prerequisite of u-boot-with-spl.imx,
u-boot-with-nand-spl.imx.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Rename OBJCFLAGS to OBJCOPYFLAGS beforehand to use
"cmd_objcopy" in scripts/Makefile.lib in an upcoming commit.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Generate include/generated/generic-asm-offsets.h and
include/generated/asm-offsets.h in ./Kbuild.
This commit also changes the include guard.
Before this commit, __ASM_OFFSETS_H__ was used for both of them.
So we could not include generic-asm-offsets.h and asm-offsets.h
at the same time.
This commit renames the include guard of the former to
__GENERIC_ASM_OFFSETS_H__.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit moves include/generated/{generic-asm-offsets.h, asm-offsets.h}
from "depend" targets to "prepare" targets and deletes "depend" targets.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
- Generate include/generated/{timestamp.h, version.h}
more simply by using filechk rule.
- Add $(UBOOTRELEASE) variable and re-write u-boot.imx rule
more simply.
- Rename U_BOOT_VERSION in Makefile to UBOOTVERSION
Before this commit, the same variable name, "U_BOOT_VERSION"
was used for two different strings.
One of them was defined in Makefile.
It takes the form like "2014.01-rc1" and used in
makefiles and script files.
The other is defined in include/generated/version.h
It takes the form like "U-Boot 2014.01-rc1-00010-gbe6d426-dirty"
and used in C and Aseembler.
It is confusing when grepping the source tree. So, this commit
renames the former to UBOOTVERSION.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If -fstack-usage option is given to crosstools
that do not support it, gcc displays a warning message
but still exits with status 0.
This means we can not rely on $(call cc-option,...)
to detect if -fstack-usage option is supported or not.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
