This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.
This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).
A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080a, LS1088a and LS2088a SOCs are based on Chassis-3 and shared
same stream-id partitioning. This patch rewords the definition to
support all these SOCs.
Also have changes in description about iommu-map property updates
in PCI node.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The stream ID allocation for Chasis 3.0 devices can be shared among
LS1088, LS2088 and LS2080.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add header address for PPA to be validated during ESBC phase for LS2080A
platform based on Layescape Chasis 3.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
from the GPIO bank number and bank's GPIO offset number.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
We only support cores that do Thumb-1 or later. So we add a comment to
explain this and remove the architecture test.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Use meaningful macros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.
Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add the iomux pins header file from iomux tool team. Change the IOMUXC0 pins
to add IOMUX_CONFIG_MPORTS flags.
Note: The IOMUXC0 offset provided in this file is from 0xD000, this is not
aligned with IOMUXC0 base address. We have adjusted the IOMUXC0 base address
to aligin with it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.
The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.
To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.
Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.
Reuse some code in imx-common.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.
SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.
In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add imx-regs.h for i.MX7ULP registers addresses definitions and some
registers structures.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add rk3328 pinctrl driver and grf/iomux structure definition.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3399 support DDR3, LPDDR3, DDR4 sdram, this patch is porting from
coreboot, support 4GB lpddr3 in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
The sdram controller blocks are very similar to the rk3288 in utilizing
memory scheduler, Designware uPCTL and Designware PUBL blocks, only
limited to one bank instead of two.
There are some minimal differences when setting up the ram, so it gets
a separate driver for the rk3188 but reuses the driver structs, as there
is no need to define the same again.
More optimization can happen when the modelling of the controller parts
in the dts actually follow the hardware layout hopefully at some point
in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
So far spl-boards have declared the back_to_brom() function as simple
extern in the files themself. That doesn't scale well if every boards
defines this on its own.
Therefore move the declarations to a bootrom header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Use defines to describe the bit shifts used to create the
table for ddrconf register values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
rk3399 has different syscon registers which may used in spl,
add to support rk3399 spl.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
rk3399 grf register bit defenitions should locate in header
file, so that not only pinctrl can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As no gpio.h is defined in arch/arm/include/asm/arch-stih410,
to avoid compilation failure, do not include asm/arch/gpio.h.
This is needed for example when including sdhci.h, which include
asm/gpio.h>.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Raw uboot image is used in place of FIT image in secure boot.
The maximum allocated size of raw u-boot bin is 1MB in memory map.
Hence , CONFIG_SYS_MONITOR_LEN has been modified to 1 MB.
The bootscript (BS_ADDR) and its header (BS_HDR_ADDR) offset on
MMC have also been modified to accommodate the increase in uboot size.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different
Add new function adjust_vdd() for LSCH3 compliant SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases this is absolutely required, so select this for some secure
features. This also requires migration of RSA_FREESCALE_EXP
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Saksham Jain <saksham.jain@nxp.freescale.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Current ARM assembler helper for the 'return to caller' pseudo-instruction
turns 'ret lr' into 'mov pc, lr' for ARMv5TE. This causes the core to remain
in its current ARM state even when the routine doing the 'ret' was called
from Thumb-1 state, triggering an undefined instruction exception.
This causes early run-time failures in all boards compiled using the Thumb-1
instruction set (for instance the Open-RD family).
ARMv5TE supports 'bx lr' which properly implements interworking and thus
correctly returns to Thumb-1 state from ARM state.
This change makes 'ret lr' turn into 'bx lr' for ARMv5TE.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
When using early malloc the allocated memory can overflow into the SRAM
scratch space, move NON_SECURE_SRAM_IMG_END down a bit to allow more
dynamic allocation at the expense of a slightly smaller maximum image
size.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PPA binary needs to be relocated on secure DDR, hence marking out
a portion of DDR as secure if CONFIG_SYS_MEM_RESERVE_SECURE flag
is set
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds glue code required for enabling the designware
mac on stm32f7 devices.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the clock setup function defined in clock.c instead of setting the
clock bits directly in the drivers.
Remove register definitions of RCC in rcc.h as these are already
defined in the struct in stm32.h
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
The fmc base address is defined twice, once in fmc.h and once in stm32.h.
Fix wrong definition in stm32.h.
Remove the definiton in fmc.h.
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Cleanup stm32f7 files:
- use BIT macro
- use GENMASK macro
- use rcc struct instead of macro additions
Add missing stm32f7 register in rcc struct
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA<vikas.manocha@st.com>
The check for OMAP3630/3730 only checks for 800MHz 3630/3730, but
anything else is lumped into 36XX/37XX with an assumed 1GHz speed.
Based on the DM3730 TRM bit 9 shows the MPU Frequency (800MHz/1GHZ).
This also adds the ability to distinguish between the DM3730, DM3725,
AM3715, and AM3703 and correctly display their maximum speed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
chiliSOM is a System On Module (http://http://grinn-global.com/chilisom/).
It can't exists on its own, but will be used as part of other boards.
Hardware specification:
* TI AM335x processor
* 128M, 256M or 512M DDR3 memory
* up to 256M NAND
We place source inside arch/arm/mach-omap2/ directory and make it
possible to reuse initialization code (i.e. DDR, NAND init) for all
boards that use it.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.
[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce board/freescale/common/Kconfig so that we have a single place
for CONFIG options that are shared between ARM and PowerPC NXP platforms.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the config FSL_PPA_ARMV8_PSCI from fsl-layerscape's Kconfig to
Kconfig under armv8 and renamed it to SEC_FIRMWARE_ARMV8_PSCI.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For 64-bit kernel, there is a warning about x1-x3 nonzero in violation
of boot protocol. To fix this issue, input argument 4 is added for
armv8_switch_to_el2 and armv8_switch_to_el1. The input argument 4 will
be set to the right value, such as zero.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS1043A rev1.1 silicon supports two types of GIC offset: 4K
alignment and 64K alignment. The bit SCFG_GIC400_ALIGN[GIC_ADDR_BIT]
is used to choose which offset will be used.
The LS1043A rev1.0 silicon only supports the CIG offset with 4K
alignment.
If GIC_ADDR_BIT bit is set, 4K alignment is used, or else 64K alignment
is used. 64K alignment is the default setting.
Overriding the weak smp_kick_all_cpus, the new impletment is able to
detect GIC offset.
The default GIC offset in kernel device tree is using 4K alignment, it
need to be fixed if 64K alignment is detected.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Set up chip power supply voltage according to voltage ID.
The fuse status register provides the values from on-chip
voltage ID fuses programmed at the factory. These values
define the voltage requirements for the chip.
Main operations:
1. Set up the core voltage
2. Set up the SERDES voltage and reset SERDES lanes
3. Enable/disable DDR controller support 0.9V if needed
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update bootscript and its hdr addresses for Layerscape Chasis 3
based platforms instead of individual SoCs.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Up to now, there are 3 kind of SoCs under Layerscape Chassis 2,
like LS1043A, LS1046A and LS1012A. But the clocks tree has a
lot of differences, for instance, the IP modules have different
dividers to derive its clock from Platform PLL. And the core
cluster PLL and platform PLL maybe have different reference
clocks, such as LS1012A. Another problem is which clock/PLL
should be described by sys_info->freq_systembus, it is confused
in Layerscape Chissis 2.
This patch is to bind the sys_info->freq_systembus to the Platform
PLL, and handle the different divider of IP modules separately
between different SoCs, and separate reference clocks of core
cluster PLL and platform PLL.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Clear the content to zero and the ECC error bit of OCRAM1/2.
The OCRAM must be initialized to ZERO by the unit of 8-Byte before
accessing it, or else it will generate ECC error. And the IBR has
accessed the OCRAM before this initialization, so the ECC error
status bit should to be cleared.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The real size of OCRAM is 128KiB, so correct the size of OCRAM.
And OCRAM reserved 2MiB space, then add a new macro to describe
it, which is used for MMU setup.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
