On i.MX8, when booting from eMMC boot partition, the whole flash.bin
is stored in boot partition, however SPL switches to user partition
during the init of mmc driver:
spl_mmc_load() -> mmc_init()
Then it tries to load the container image in
spl_mmc_get_uboot_raw_sector(), but here it reads the data from user
partition and the header is not recognized as a valid header.
So we move spl_mmc_get_uboot_raw_sector after eMMC partition switch
to address this issue.
Anyway put spl_mmc_get_uboot_raw_sector before eMMC partition switch
is not correct, so let's move it after eMMC partition switch.
Reported-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It is possible to enable bootstage in TPL. TPL can stash the info for SPL.
But at present this information is then lost because SPL does not read
from the stash.
Add support for SPL not being the first phase to enable bootstage.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootstage in TPL and SPL use the same ID so it is not possible
to see the timing of each. Separate out the IDs and use the correct one
depending on which phase we are at.
Example output:
Timer summary in microseconds (14 records):
Mark Elapsed Stage
0 0 reset
224,787 224,787 TPL
282,248 57,461 end TPL
341,067 58,819 SPL
925,436 584,369 end SPL
931,710 6,274 board_init_f
1,035,482 103,772 board_init_r
1,387,852 352,370 main_loop
1,387,911 59 id=175
Accumulated time:
196 dm_r
8,300 dm_spl
14,139 dm_f
229,121 fsp-m
262,992 fsp-s
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootstage relocation assumes that it is possible to point back
to memory available before relocation, so it does not relocate the
strings. However this is not the case on some platforms, such as x86 which
uses the cache as RAM and loses access to this when the cache is enabled.
Move the relocation step to before U-Boot relocates, expand the allocated
region to include space for the strings and relocate the strings at the
same time as the bootstage records.
This ensures that bootstage data can remain accessible from TPL through
SPL to U-Boot before/after relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is a single shared address for bootstage data in both
TPL and SPL. If SPL unstashs TPL bootstage info and then stashes it again
to pass it to U-Boot, the new stash overwrites the strings of the old
stash.
Fix this by duplicating the strings into the malloc() region. This should
be a small code. Fix the header-file order at the same time.
This problem doesn't happen at the next stage (SPL->U-Boot) since U-Boot
relocates the boostage data.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current code searches for empty records but these not existing with
bootstage now. This used to be needed when bootstage records were stored
in a spare array.
Drop the unnecessary code and fix a code-style nit at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
When stashing bootstage info, store the next ID so that it can be used
when the stash is restored. This avoids the ID starting at zero and
potentially overwriting existing entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make sure that the bloblist starts on an aligned boundary. This protects
against one of the early allocating causing the alignment to be lost.
Signed-off-by: Simon Glass <sjg@chromium.org>
All platforms which are using MANUAL_RELOC are jumping back to origin
location when repeatable command is called. The reason is that cmd_rep link
is not updated properly. Issue can be reproduced by rewriting origin
U-Boot location through (for example) file download by tftp command.
Fixes: 80a48dd47e ("common: command: Rework the 'cmd is repeatable' logic")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds manual relocation for struct hash_algo if
CONFIG_NEEDS_MANUAL_RELOC is enabled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Loading U-Boot on i.MX8QXP MEK board is broken since recent changes
in spl_mmc:
U-Boot SPL 2019.10-00162-gff5bd397e4 (Oct 18 2019 - 15:50:45 +0200)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
Load image from MMC/SD 0x46400
spl: mmc partition switch failed
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The newly added CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION option
is selected automatically and overrides the EXT_CSC_PART_CONFIG
configurations with default value, always selecting the eMMC boot
partition 1. Boards which place U-Boot image in other partitions
became not bootable.
Fix this by making the eMMC HW boot partition selection optional.
Fixes: 17241ea054 (spl: mmc: Add option to set eMMC HW boot partition)
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
In new versions of Android Boot Image next fields are added to the
header (and corresponding payloads are added to the image itself):
- v1: Recovery DTBO
- v2: DTB
Account for these new fields in next functions:
1. android_image_get_end(): as v1 and v2 have new payloads in the
image, the calculation of image end address should be extended
correspondingly; this is used e.g. by "bootm" command when booting
the kernel from Android Boot Image
2. android_print_contents(): new fields values in v1 and v2 should be
printed; the result of this function can be seen e.g. in "iminfo"
command
This commit doesn't add the means for working with new payloads in v1
and v2 images (it will be done in further commits), it only updates
existing functions w.r.t. changes in boot image v1/v2.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
This define indicates if DM_SPI shall be supported in SPL. This allows
proper operation of DM converted SPI drivers in SPL, which use
#if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted
boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change allows setting pre-defined eMMC boot partition for SPL eMMC
booting. It is necessary in the case when one wants to boot (through falcon
boot) from eMMC after loading SPL from other memory (like SPI-NOR).
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Edit the commit message]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
This fixes a wrongly indented block of code.
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Make the commit message more verbose]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit add a generic function board_init_f that
only initialize some device (for example serial). It
avoid to define a board function only to launch the
serial configuration.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Expose SPL's Y-Modem core loader function via the common SPL header
file so it can be re-used for purposes other than loading U-Boot itself.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
During FIT reading through ymodem_read_fit() the function
xyzModem_stream_read() is being used which returns zero once the end
of a stream has been reached. This could lead to an premature exit from
ymodem_read_fit() with certain-sized FIT images reporting that zero
bytes overall were read. Such a premature exit would then result in an
-EIO failure being triggered within the spl_load_simple_fit() caller
function and ultimately lead to a boot failure.
Fix this logic by simply aborting the stream read loops and continuing
with the regular code flow which ultimately would lead to returning
the number of bytes to be read ('size') as expected by the callers of
ymodem_read_fit().
Fixes: fa715193c0 ("spl: Add an option to load a FIT containing U-Boot from UART")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The write functions do actually change the contents of memory so it is not
correct to use 'const'. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce weak spl_nand_get_uboot_raw_page, then platform could
have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Introduce weak spl_nor_get_uboot_base, then platform have their own
implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Introduce a weak function spl_spi_get_uboot_offs, then
platform could have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Introduce a weak function spl_mmc_get_uboot_raw_sector, then platform
could have their own implementation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The default CSF_SIZE defined in Kconfig is too high and SPL cannot
fit into the OCRAM in certain cases.
The CSF cannot achieve 0x2000 length when using RSA 4K key which is
the largest key size supported by HABv4.
According to AN12056 "Encrypted Boot on HABv4 and CAAM Enabled Devices"
it's recommended to pad CSF binary to 0x2000 and append DEK blob to
deploy encrypted boot images.
As the maximum DEK blob size is 0x58 we can reduce CSF_SIZE to 0x2060
which should cover both CSF and DEK blob length.
Update default_image.c and image.c to align with this change and avoid
a U-Boot proper authentication failure in HAB closed devices:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x32 length=0x6131 version=0x38
bad length magic=0x32 length=0x6131 version=0x38
bad version magic=0x32 length=0x6131 version=0x38
spl: ERROR: image authentication fail
Fixes: 96d27fb218 (Revert "habv4: tools: Avoid hardcoded CSF size for SPL targets")
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
This change tries to fix the following problem:
- The board boots (to be more precise - ROM loads SPL) from a slow SPI-NOR
memory.
As a result the spl_boot_device() will return SPI-NOR as a boot device
(which is correct).
- The problem is that in 'falcon boot' the eMMC is used as a boot medium to
load kernel from its partition.
Calling spl_boot_device() will break things as it returns SPI-NOR device.
To fix this issue the new CONFIG_SPL_FORCE_MMC_BOOT Kconfig flag is
introduced to handle this special use case. By default it is not defined,
so there is no change in the legacy code flow.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Currently it's not possible to authenticate the U-Boot proper of
mx6ul_14x14_evk_defconfig target:
Authenticate image from DDR location 0x877fffc0...
bad magic magic=0x0 length=0x00 version=0x3
bad length magic=0x0 length=0x00 version=0x3
bad version magic=0x0 length=0x00 version=0x3
spl: ERROR: image authentication fail
Commit 0633e13478 ("imx: hab: Increase CSF_SIZE for i.MX6 and
i.MX7 devices") has increased CSF_SIZE to avoid a possible issue
when booting encrypted boot images.
Commit d21bd69b6e ("tools: mkimage: add firmware-ivt image type
for HAB verification") is hardcoding the CSF and IVT sizes, the
new CSF size is not being considered and u-boot-ivt.img fails to
boot.
Avoid hardcoded CSF and IVT size to fix this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Microblaze as Arm is using multiple memory banks which are read from DT
that's why there is a need to initialized LMB based on bd->bi_dram[].
Without this fix memory base/size is all the time 0 and image relocation is
not possible.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define default address via Kconfig. There is no need to change this address
for most of the boards but it is also possible. This one line save a lot of
lines in defconfigs that's why make sense to do it.
The similar change has been done by commit 9340d8fe8b
("sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
This is currently a decimal value which is not as convenient or
meaningful. Also U-Boot tends to use hex everywhere.
Convert this option to hex and add a comment for the size_check macro.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the typo in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the bloblist is set up in spl_common_init() which can be called
from spl_early_init(), i.e. before SDRAM is ready. This prevents the
bloblist from being located in SDRAM, which is useful on some platforms
where SRAM is inaccessible after U-Boot relocates (e.g. x86 CAR region).
It doesn't serve much purpose to have the bloblist available early, since
very little is known about the platform then, and the handoff info is
written when SPL is about to jump to U-Boot.
Move the code to board_init_r() to avoid any restrictions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present there is an arch-specific area in the SPL handoff area intended
for use by arch-specific code, but there is no explicit call to fill in
this data. Add a hook for this.
Also use the hook to remove the sandbox-specific test code from
write_spl_handoff().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these options can be enabled when bloblist is not enabled for
SPL or TPL. This is incorrect as SPL handoff requires bloblist. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Old splash code in cfb_console driver displayed U-Boot version
string by default. Restore this behaviour for DM_VIDEO enabled
configurations.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
After mxc_ipuv3 DM_VIDEO conversion board configs with enabled
CONFIG_VIDEO_LOGO do not show splash screen (previosly drawing
splash screen worked via cfb_console driver with CONFIG_VIDEO_LOGO
enabled). Use splash_source library for loading splash images
when CONFIG_SPLASH_SOURCE is selected, otherwise prepare built-in
video logo for drawing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The current code in reserve_noncached() has two issues:
1) The first update of gd->start_addr_sp always rounds down to a section
start. However, the equivalent calculation in cache.c:noncached_init()
always first rounds up to a section start, then subtracts a section size.
These two calculations differ if the initial value is already rounded to
section alignment.
2) The second update of gd->start_addr_sp subtracts exactly
CONFIG_SYS_NONCACHED_MEMORY, whereas the equivalent calculation in
cache.c:noncached_init() rounds the noncached size up to section
alignment before subtracting it. The two calculations differ if the
noncached region size is not a multiple of the MMU section size.
In practice, one/both of those issues causes a practical problem on
Jetson TX1; U-Boot triggers a synchronous abort during initialization,
likely due to overlapping use of some memory region.
This change fixes both these issues by duplicating the exact calculations
from noncached_init() into reserve_noncached().
However, this fix assumes that gd->start_addr_sp on entry to
reserve_noncached() exactly matches mem_malloc_start on entry to
noncached_init(). I haven't traced the code to see whether it absolutely
guarantees this in all (or indeed any!) cases. Consequently, I added some
comments in the hope that this condition will continue to be true.
Fixes: 5f7adb5b1c ("board_f: reserve noncached space below malloc area")
Cc: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Define new image type for coprocessor images.
It is used in FIT to identify the files loaded
with remoteproc command (elf or bin).
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, SPL/TPL options
when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit. In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
Noncached area at present is being initialized to random space after malloc
area. It works in most the cases as it goes to stack area & stack is not
overwriting it being far from it.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
To support relocation of the stack and global data on RISC-V, the
secondary harts must be notified of the change using IPIs. We can reuse
the hart relocation code for this purpose. It uses global data to store
the new stack pointer and global data pointer for the secondary harts.
This means that we cannot update the global data pointer of the main
hart in spl_relocate_stack_gd(), because the secondary harts have not
yet been relocated at this point. It is updated after the secondary
harts have been notified.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
RISC-V OpenSBI is an open-source implementation of the RISC-V Supervisor
Binary Interface (SBI) specification. It is required by Linux and U-Boot
running in supervisor mode. This patch adds support for booting via the
OpenSBI FW_DYNAMIC firmware. It supports OpenSBI version 0.4 and higher.
In this configuration, U-Boot SPL starts in machine mode. After loading
OpenSBI and U-Boot proper, it will start OpenSBI. All necessary
parameters are generated by U-Boot SPL and are passed to OpenSBI. U-Boot
proper is started in supervisor mode by OpenSBI. Support for OpenSBI is
enabled with CONFIG_SPL_OPENSBI. An additional configuration entry,
CONFIG_SPL_OPENSBI_LOAD_ADDR, is used to specify the load address of the
OpenSBI firmware binary. It is not used directly in U-Boot and instead
is intended to make the value available to scripts such as FIT
configuration generators.
The header file include/opensbi.h is based on header files from the
OpenSBI project. They are recent, as of commit bae54f764570 ("firmware:
Add fw_dynamic firmware").
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
As part of the SPL FIT boot flow, the device tree is appended to U-Boot
proper. The device tree is used to record information on the loadables
to make them available to the SPL framework and U-Boot proper. Depending
on the U-Boot device tree provider, the FIT image might not include a
device tree. Information on the loadables is missing in this case.
When booting via firmware bundled with the FIT image, U-Boot SPL loads
the firmware binary and U-Boot proper before starting the firmware. The
firmware, in turn, is responsible for starting U-Boot proper.
Information on the memory location of the U-Boot proper loadable must be
available to the SPL framework so that it can be passed to the firmware
binary. To support this use case when no device tree is found in the FIT
image, fall back to the U-Boot device tree in this situation.
At the same time, update the comment to remove the note that the
destination address must be aligned to ARCH_DMA_MINALIGN. Alignment is
only required as an intermediate step when reading external data. This
is automatically handled by spl_fit_append_fdt(). After reading the
external data, it is copied to the specified address, which does not
have to be aligned to ARCH_DMA_MINALIGN.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
This converts the following to Kconfig:
CONFIG_SYS_SPI_U_BOOT_OFFS
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present we have environment.h but this file includes all the
environment-related header files as well as internals such as
default_environment.
It seems desirable to have a new header to hold the commonly used
environment functions, so that most files can avoid including all of this
unnecessary stuff.
Create a new env.h header and move one function over to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This function relates to lcd.h and is about to become obsolete with the
driver-model conversion. Move it out of common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This implements a stack usage check in SPL.
Many boards start up SPL to run code + data from one common, rather small
SRAM. To implement a sophisticated SPL binary size limit on such boards,
the stack size (as well as malloc size and global data size) must be
subtracted from this SRAM size.
However, to do that properly, the stack size first needs to be known.
This patch adds a new Kconfig option:
- SPL_SYS_REPORT_STACK_F_USAGE: memset(0xaa) the whole area of the stack
very early and check stack usage based on this constant later before the
stack is switched to DRAM
Initializing the stack and checking it is implemented in weak functions,
in case a board does not use the stack as saved in gd->start_addr_sp.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The Linux ramdisk should always be decompressed by the kernel itself,
not by U-Boot. Therefore, the 'compression' node in the FIT image should
always be set to "none" for ramdisk images, since the only point of
using that node is if you want U-Boot to do the decompression itself.
Yet some systems populate the node to the compression algorithm used by
the kernel instead. This used to be ignored, but now that we support
decompression of all image types it becomes a problem. Since ramdisks
should never be decompressed by U-Boot anyway, this patch adds a special
exception for them to avoid these issues. Still, setting the
'compression' node like that is wrong in the first place, so we still
want to print out a warning so that third-party distributions doing this
can notice and fix it.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Avoid to flush buffer when silent console is activated as the
console can be reactivate later, after relocation, when the env will
be updated with the saved one.
Solve issue (missing beginning of U-Boot trace) when:
- CONFIG_SILENT_CONSOLE is activated
- silent=1 is defined in default environment (CONFIG_EXTRA_ENV_SETTINGS)
- silent is removed in saved environment with:
> env delete silent; env save
Only functional when PRE_CONSOLE_BUFFER is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update the "silent" property with the variable "silent" get from
saved environment, it solves the issue when:
- CONFIG_SILENT_CONSOLE and CONFIG_SYS_CONSOLE_IS_IN_ENV are activated
- silent is not defined in default environment
- silent is requested in saved environment with:
> env set silent 1; env save
On next reboot the console is not disabled as expected after relocation
and the environment load from flash (the callback is not called when
the INSERT is requested in the created hash table)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When having only these AVB related configs enabled:
CONFIG_AVB_VERIFY=y
CONFIG_CMD_AVB=y
CONFIG_LIBAVB=y
build fails with next errors:
common/avb_verify.c: In function 'read_persistent_value':
common/avb_verify.c:867:6: warning: implicit declaration of function
'get_open_session'
common/avb_verify.c:870:45: error: 'struct AvbOpsData' has no member
named 'tee'
common/avb_verify.c:894:7: warning: implicit declaration of function
'invoke_func'
common/avb_verify.c: In function 'write_persistent_value':
common/avb_verify.c:931:45: error: 'struct AvbOpsData' has no member
named 'tee'
Guard read_persistent_value() and write_persistent_value() functions
by checking if CONFIG_OPTEE_TA_AVB is enabled (as those are only used in
that case) to fix the build with mentioned configuration.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
if CONFIG_AUTOBOOT_KEYED, CONFIG_AUTOBOOT_ENCRYPTION and
CONFIG_AUTOBOOT_STOP_STR_SHA256 are enabled in conjunction
with CONFIG_SHA_HW_ACCEL and CONFIG_FSL_CAAM, we get the
Error when pressing a key while waiting for bootdelay:
Error: Address arguments are not aligned
CAAM was not setup properly or it is faulty
Reason is, that used variables are not cache aligned,
so malloc this variables cache aligned.
Probably this is also a bugfix for other hw accelerators
than CAAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Move the variable to the top of the file and adjust the code which uses it
to use if() rather than #ifdef, to make it easier to read.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not defined by any board. We could use CONFIG_AUTOBOOT_PROMPT
instead perhaps, but this depends on CONFIG_AUTOBOOT_KEYED which is not
used for the single-key case.
So let's just remove CONFIG_MENUPROMPT.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have two functions named __autoboot() which do different
things. This is confusing. Fix it by using if() instead of #ifdef for
selecting the functions, and renaming them to meaningful names.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use if() instead for this option, renaming the two different
passwd_abort() functions to indicate their purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
This CONFIG option is only present if CONFIG_AUTOBOOT_ENCRYPTION is
enabled so it cannot be used in code without that #ifdef. But we want to
reduce the use of #ifdef in this file and in particular to avoid having
two different functions both named passwd_abort() but which do different
things.
In preparation for this, create an intermediate value which is set to an
empty string if there is no value for CONFIG_AUTOBOOT_STOP_STR_SHA256.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function name indicates that it does something, but its entire
operation is actually condition on a CONFIG. Move the condition outside
the function so this is clearer, and use if() instead of #ifdef, like the
reset of the file.
Signed-off-by: Simon Glass <sjg@chromium.org>
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXUCEtQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLYhAJ4gSCCx54ubBmbsZ1cueGk59E/SkwCdFl7nfLqz
Vy/HbBVAUkzD4JVOR0U=
=7rSM
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix EDID mode filtering
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
Add a condition to the break in the modes lookup, without this
when the first mode is not valid, then edid_get_timing_validate()
return an error instead of checking the next modes.
Fixes: 1c1ed441b0 ("edid: add edid_get_timing_validate() variant to filter out edid modes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
recently added gpio hog patch was "in discussion"
state with Simon Glass. This patch now adds most
of comments from Simon Glass.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds support for an optional optimization to compatible
string matching where the compatible string property from the root node
of the kernel FDT can be copied into the configuration node of the FIT
image. This is most useful when using compressed FDTs or when using FDT
overlays, where the traditional extraction of the compatible string from
the kernel FDT itself is not easily possible.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for compressing non-kernel image nodes in a FIT
image (kernel nodes could already be compressed previously). This can
reduce the size of FIT images and therefore improve boot times
(especially when an image bundles many different kernel FDTs). The
images will automatically be decompressed on load.
This patch does not support extracting compatible strings from
compressed FDTs, so it's not very helpful in conjunction with
CONFIG_FIT_BEST_MATCH yet, but it can already be used in environments
that select the configuration to load explicitly.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Upcoming patches want to add decompression to use cases that are no
longer directly related to booting. It makes sense to retain a single
decompression routine, but it should no longer be in bootm.c (which is
not compiled for all configurations). This patch moves
bootm_decomp_image() to image.c and renames it to image_decomp() in
preparation of those upcoming patches.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix warning around handle_decomp_error being unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
The original edid_get_timing() function returns the first valid timing,
but on some plaforms, we could only supports a subset of the listed
monitot's navite timing.
Let's introduce a edid_get_timing_validate() adding a mode_valid callback
including a private cookie pointer.
If the callback returns false, the current timing is discared and the next
one is checked. If no valid & supported timings are found, the function
would return an error.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
A few device-tree fixes
Binman support for extracting files from an image
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl04t50RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYGPwgAlK9Jw/UoLuag8I1rd6nS8U/EYFP4VRrS
ND5Vpe+3WxuMZvrTZyeg1oOkC6UwCJZJMJPFDN2j+VD8LzUYHymTfBykJZLq11Ks
wAieldpK75ZqKcafHP8TI3L5a2fjTj20Rgg9R3IXjy8pPp9sdtqr/GiupaEY3AJf
Y8SQrL7NRZBKxfaRZZAp2MzbzjyUDwmrgntx/xd0Tr/WwZlOf+dojyAdzKP4udfF
9JcEDi4UOyF/9YBzaSfhYO5h38ZdFan+oXpeXDwjWK5w5YV9uheXLChzloF3d9T0
CRPGfFcyl1EowDO1KB3L73HROAURzEJ8gn76IEqHraHm6dqdmU372g==
=9x0F
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-24jul19-take3' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
Minor driver-model fixes and tweaks
A few device-tree fixes
Binman support for extracting files from an image
The fdt_pci_dma_ranges() cannot work on e.g. ARM, since the DT entries
endianness is not adjusted at all. Fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Currently, fdt_get_base_address() returns 0 if the "reg" property is
missing. Since 0 is a valid value, it is not suitable for the error
handling. Return OF_BAD_ADDR instead.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support load of the U-Boot image from raw SATA disk sector. This is
equivalent to load from MMC raw sector.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This patch determines the A/B-specific bootloader message structure
that is the basis for implementation of recovery and A/B update
functions. A/B metadata is stored in this structure and used to decide
which slot should we use to boot the device. Also some basic functions
for A/B metadata manipulation are implemented (like slot selection).
The patch was extracted from commits [1], [2] with some coding style
fixes.
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729878/2
[2] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows to use any available compression format with Android boot image
Since not all available compression formats have a magic number we should
explicitly specify type of compression.
For this purpose using uImage format becomes very useful, as this format is
well-known by the community and mkimage tool is already available.
Usage example:
mkimage -A ARM64 -T kernel -C lzma -d Image.lzma out/kernel
At this moment only -C option is handled, but specifying -A and -T options
are recommended for compatibility reasons in the future.
Kernel that compressed with LZ4 can be already used without wrapping into
the uImage, but I recommend wrapping it into the uImage in order to avoid
situations when by some mistake legacy LZ4 is used, that is interpreted as
raw Image and causes CPU to enter Exception Handler without providing any
meaningful explanation to the user.
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
If there is only one menu item available, prompting user to enter
choice makes little sense and just causes unnecessary boot delay. This
change makes menu_get_choice return the only one item when there is no
other choices.
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Add the following functions to translate DMA address to CPU address:
- dev_translate_dma_address()
- ofnode_translate_dma_address()
- of_translate_dma_address()
- fdt_translate_dma_address()
These functions work the same way as xxx_translate_address(), with the
difference that the translation relies on the "dma-ranges" property
instead of the "ranges" property.
Add related test. Test report:
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Use CONFIG_IS_ENABLED(WDT) to permit use of WDT in SPL without DM,
while the full U-Boot can use rich DM/DT WDT driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
The autocompletion did not work if CONFIG_CMDLINE_PS_SUPPORT was enabled
because U-Boot was comparing the prompt string with CONFIG_SYS_PROMPT .
While this works if CONFIG_CMDLINE_PS_SUPPORT is disabled, this no longer
works if it's enabled because user can override the PS1 . Fix this by
checking prompt string against the current PS1 value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
The current U-Boot SPL image loader infrastructure is very powerful,
able to initialize and load from a variety of boot media however it
is strongly geared towards loading specific types of images in a very
specific way. To address the need being able to use this infrastructure
to load arbitrary image files go ahead and refactor it as follows:
- Refactor existing spl_mmc_load_image function into superset function,
accepting additional arguments such as filenames and media load offset
(same concept can also be applied toother spl_XXX_load_image functions)
- Extend the loader function to "remember" their peripheral initialization
status so that the init is only done once during the boot process,
- Extend the FIT image loading function to allow skipping the parsing/
processing of the FIT contents (so that this can be done separately
in a more customized fashion)
- Populate the SPL_LOAD_IMAGE_METHOD() list with a trampoline function,
invoking the newly refactored superset functions in a way to maintain
compatibility with the existing behavior
This refactoring initially covers MMC/SD card loading (RAW and FS-based).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some platform we have sufficient memory available early on to allow
setting up and using a basic BSS prior to entering board_init_f(). Doing
so can for example be used to carry state over to board_init_r() without
having to resort to extending U-Boot's global data structure.
To support such scenarios add a Kconfig option called CONFIG_SPL_EARLY_BSS
to allow moving the initialization of BSS prior to entering board_init_f(),
if enabled. Note that using this option usually should go along with using
CONFIG_SPL_SEPARATE_BSS and configuring BSS to be located in memory
actually available prior to board_init_f().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.
To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
When we have a FIT image being used by SPL by default that means the
most common case is that we'll never run into a legacy image. Disable
legacy image support by default in that case to reclaim space.
Signed-off-by: Tom Rini <trini@konsulko.com>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow the code to build when FS_FAT is not enabled, and thus
spl_load_image_fat() is not provided.
A subsequent patch should add alternative raw access U-Boot main image
load method.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The init_sata() routine is only present when DM_SCSI is not enabled.
Don't call init_sata() when DM_SCSI is enabled. The code will fall back
to scsi_scan() in this case.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Add sensible defaults for the FAT partition selection and the main
U-Boot image file name. This allows spl_sata to build when the board
headers does not select them explicitly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Correct the debug output for the trace buffer size to accommodate trace
buffers exceeding 2GiB.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Compiling with TRACE but without TRACE_EARLY results in an error
aarch64-linux-gnu-ld.bfd:
common/built-in.o:(.rodata.init_sequence_f+0x10):
undefined reference to `trace_early_init'
trace_early_init() should not be called if CONFIG_TRACE_EARLY is not
defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
If bootstage is enabled in TPL it lacks a record count and so does not
build. Fix this by adding a new Kconfig option.
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows to silence ubi and ubispl individually.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
The motivation is to use the UBI atomic volume rename functionality to
allow double copy software updates on UBI. To that end the SPL is
configured to always load the same volume name (e.g. "u-boot"),
whereas a software updater always installs into the secondary volume
"u-boot_r". After successful installation, these two volume names are
switched.
This extension is protected by #ifdefs as it will somewhat slow down
loading of volumes by id. This is because the code needs to disable
the optimization of ignoring all volume ids which are not
to-be-loaded, since these can only be resolved after attaching.
This adds two vtbl related functions from Linux, which are taken from
the same kernel version as the current main U-Boot UBI code (Linux 4.2
64291f7db5bd8).
Signed-off-by: Hamish Guthrie <hamish.guthrie@kistler.com>
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Move the ubispl configuration to KConfig and drop them from the
whitelist.
Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
The initr_watchdog is currently placed before initr_serial. The
initr_watchdog calls printf and printf finally calls ops->putc of a serial
driver.
However, gd->cur_serial_dev points to a udevice allocated in board_f. The
gd->cur_serial_dev->driver->ops->putc points the the code region before
relocation.
Some serial drivers call WATCHDOG_RESET() in ops->putc. When DM is enabled
for watchdog, watchdog_reset() is called. watchdog_reset() calls get_timer
to get current timer.
On some platforms the timer driver is also a DM driver. initr_watchdog is
placed right after initr_dm, which means the timer driver hasn't been
initialized. So dm_timer_init() is called. To create a new udevice, calloc
is called.
However start from ops->putc, u-boot execution flow is redirected into the
memory region before relocation (board_f). In board_f, dlmalloc hasn't
been initialized. The call to calloc will fail, and this will cause DM to
print out an error message, and it will call printf again, causing
recursive error outputs.
This patch places initr_watchdog after initr_serial to solve this issue.
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
The pointer to struct atf_image_info in
bl31_params_mem.bl31_params.bl31_image_info is not initialized before
being dereferenced. This can cause U-Boot to crash right before jumping
to the BL31 ATF binary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: bcc1726a7b ("spl: add support to booting with ATF")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for loading u-boot FIT images over the USB SDP protocol in
the SPL
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[Various build fixes]
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
Previously we would store NULL in info->padding and jump to an illegal
instruction if an unknown value for "padding" was specified in the
device tree.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com>
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
The SPL DFU uses dfu_alt_info_N variable name to determine the DFU
configuration, where N is the name of the media (e.g. ram). It does
not use the plain dfu_alt_info. Print the name of the missing env
variable in case of a failure instead of printing dfu_alt_info,
which is just the name of the parameter passed to spl_dfu_cmd().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
As explained in include/configs/imx6_spl.h. the i.MX6 SPL
size limit is 68KB (4KB header + 64KB max size).
Provide such limit for all i.MX6 boards that use SPL
to detect SPL size overflow in build time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
When introduced this limit was an int but was then changed to hex
without noting as much in the prompt nor changing existing users. Put
this back to an int.
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Fixes: 2577015dc5 ("spl: add overall SPL size check")
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a size check for SPL that can dynamically check generated
SPL binaries (including devicetree) for a size limit that ensures
this image plus global data, heap and stack fit in initial SRAM.
Since some of these sizes are not available to make, a new host tool
'spl_size_limit' is added that dumps the resulting maximum size for
an SPL binary to stdout. This tool is used in toplevel Makefile to
implement the size check on SPL binaries.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
By default the configuration of the PMC is to have an external crystal
connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not
do any driving, and the XIN needs to be provided with a proper signal.
This is the MOSCXTBY bit in the PMC main clock generator register.
The SPL needs to properly initialize the PMC registers before switching
to external clock signal and raising the clock to the cruise speed.
Also created Kconfig for this specific configuration.
By default this is disabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Currently for CONFIG_DM_VIDEO=y setting splashimage env variable doesn't
have any effect. Introduce a common function for both dm-video/lcd stacks,
that checks env("splashimage") and invokes bmp_display() accordingly.
For additional details please check discussion [1].
[1] https://lists.denx.de/pipermail/u-boot/2019-May/371002.html
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJc5rdIAAoJEMrHeC97M/+mw64P/0jD3C1jvtwkzFQ2DPvnSQEk
iTZHMb91/9GncSY0S2Cgn8a2+m24F7YFLqibKSdduLLr/w98Zfi7kmO+ju/Kn+qE
aG6iomyour8+Pr+1LMPolsKKM8lULSgrd4ALRA5CegNsXijvYEE7N8mPrBpdIQem
BaM4HnQpbtxXU9J/rGHAVagLuHbJmwBvZBQTBAWfQdNR5+vGfplH2sF0cxJF5UTW
06yBXrwjLW6PEVYZbzYiRQ5Gn7BnBe4nXrl4ReDtS5e4ueRKM166TZljvNCd60KI
B49eLxd0wT2Zutsz1rT5c/LChXo3cr8FXM3csJ6J6cIBdfFF3frHbIEDM2jZTxJf
jN7pAHpxbRdYS/GbWS5mSuUyKmxDPt6Kfd7LQUYX9qktqeLG9LfkrmLfGdCSiwkB
64Z15DoHAuDMab+LlV+rz8ns3YAV0ruFryWfZ8udLWuX3G6NDmivafLR3dgNRdNB
otkyCdIlq8GQUm3w+5r9wm7aGvHB3UtNYK870AnYA20vmn/WVuUBZ6yE+lce/QpV
zFS4dgsdbn41EXO/O9TtwMyKT+/s138u2+L7CEegXiNneJmwzbJg3YPeMuaiF8Y2
oYqlUmfVO/ZuoVvr5dwo4TY96nEhRf2Ul36spRdrx8wBZ0YdL+ByDO5Pcc2B9A+P
M80QqlT64BJDJ1CqhW5m
=meeB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190523' of https://github.com/pchotard/u-boot
- Add various STM32MP1 fixes for serial, env, clk, board, i2c ...
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
This debug mode is used by CubeMX DDR tuning tools
or manualy for tests during board bring-up.
It is simple console used to change DDR parameters and check
initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When using fdt_fixup_mtdparts() offset and length cell sizes
are limited to 4 bytes (1 cell). However if the mtd device is
bigger then 4GiB, then #address-cells and #size-cells are
8 bytes (2 cells) [1].
This patch read #size-cells and uses either fdt32_t or
fdt64_t cell size. The default is fdt32_t.
[1] Documentation/devicetree/bindings/mtd/partition.txt
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXOK5Sw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBvoAJ96YrInVKKWtuVigA9lNpk5xbmbeQCdG9wML4LI
dBbQyzD3mNqvnDMyNPQ=
=Plt7
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc3' of git://git.denx.de/u-boot-video
- update for using splashfile instead of location->name
when loading the splash image from a FIT
- updates for loading internal and external splash data from FIT
- DM_GPIO/DM_VIDEO migration for mx53 cx9020 board
- fix boot issue on mx6sabresd board after DM_VIDEO migration
- increase the max preallocated framebuffer BPP to 32 in ipuv3
driver to prepare for configurations with higher color depth
- allow to use vidconsole_put_string() in board code for text
output on LCD displays
The FIT image could contain the splash data in 3 different structure:
- The splash data is embedded in FIT image (internal)
In this case, the property 'data' presents in FIT image header. And
internal information 'start' and 'end' represent the location and
size of splash data inside of FIT image.
- The splash data is external with absolute position in FIT image
This case is made by 'mkimage -p [pos]'. The splash data is stored
at the absolute position. Instead the property 'data', the properties
'data-position' and 'data-size' are used to specify the location and
size of the splash data.
- the splash data is external with relative offset in FIT image
This case is made by 'mkimage -E'. The splash data is placed after
the FIT image header with 4 byte alignment. Instead the property
'data', the properties 'data-offset' and 'data-size' are used to
specify the location and size of the splash data.
Currently, the splash only support to load external data with relative
offset from FIT image. This commit make it possible to load the splash
data embedded in FIT image or the external data with absolute position
This inspiration comes from Simon Glass <sjg@chromium.org>, see
common/spl_fit.c
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The splash image could be loaded from different sources (e.g. sf, mmc)
with different formats (e.g. raw, file-system). These sources are
structured by a board dependent object 'splash_location'. To decide
where is the splash image loaded, following environment variables are
used to select the splash source and file:
- 'splashsource' is used to select the splash source by setting its
value to specified name of splash location.
- 'splashfile' specify the name of splash image file
But, when loads the splash image from FIT, the name of splash image
within FIT is specified by splash location name. Due to the splash
location name is already used for the splash source, its name may
conflicts with the name of splash image.
To solve the conflict, the environment variable 'splashfile' is used
to specify the splash image in FIT, and keeps the splash location
name for the splash source.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tomas Melin <tomas.melin@vaisala.com>
Set the spl_image->fdt_addr pointer both for simple fitImage configuration
as well as full fitImage configuration, to let spl_perform_fixups() access
the DT and perform modifications to it if necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function merely relocates the fdt blob, so don't let it alter
it by adding reservations that didn't exist before.
Instead, if the memory used for the fdt blob has been reserved
before calling this function, ensure the relocated memory is
marked as reserved instead.
Reported-by: Keerthy <j-keerthy@ti.com>
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Due to some mistakes in the source code, it was not possible to really
turn FIT support off. This commit fixes the problem by means of the
following changes:
- Enclose "bootm_host_load_image" and "bootm_host_load_images" between
checks for CONFIG_FIT_SIGNATURE, in common/bootm.c.
- Enclose the declaration of "bootm_host_load_images" between checks for
CONFIG_FIT_SIGNATURE, in common/bootm.h.
- Condition the compilation and linking of fit_common.o fit_image.o
image-host.o common/image-fit.o to CONFIG_FIT=y, in tools/Makefile.
Signed-off-by: Carlos Santos <casantos@datacom.ind.br>
[fabio: adapt for 2016.07]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
[Ricardo: fix conditional compilation and linking of the files mentioned above
for 2016.07]
Signed-off-by: Ricardo Martincoski <ricardo.martincoski@gmail.com>
[Jörg: adapt for 2019.01]
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
[Retrieved from:
https://git.buildroot.net/buildroot/tree/package/uboot-tools/0003-Make-FIT-support-really-optional.patch]
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
FIT_IMAGE_TINY is used to reduce the size of the SPL by removing os-type
tracking and recording the loadables into the loaded FDT. When this option
is enabled, it is assumed that the next stage firmware is u-boot.
However this does not play well with the SPL_OS_BOOT option that enables
loading different type of next stage firmware, like the OS itself.
When SPL_OS_BOOT is used, do not disable os-tracking. The added footprint
is about 300 Bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
AVB 2.0 spec. revision 1.1 introduces support for named persistent values
that must be tamper evident and allows AVB to store arbitrary key-value
pairs [1].
Introduce implementation of two additional AVB operations
read_persistent_value()/write_persistent_value() for retrieving/storing
named persistent values.
Correspondent pull request in the OP-TEE OS project repo [2].
[1]: https://android.googlesource.com/platform/external/avb/+/android-9.0.0_r22
[2]: https://github.com/OP-TEE/optee_os/pull/2699
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
According to Android image format [1], kernel image resides at 1 page
offset from the boot image address. Grab the magic number from there
and allow U-Boot to handle LZ4-compressed KNL binaries instead of
hardcoding compression type to IH_COMP_NONE. Other compression types,
if needed, can be added later.
Tested on H3ULCB-KF using the image detailed in [2].
[1] Excerpt from include/android_image.h
+-----------------+
| boot header | 1 page
+-----------------+
| kernel | n pages
+-----------------+
| ramdisk | m pages
+-----------------+
| second stage | o pages
+-----------------+
[2] => iminfo 4c000000
## Checking Image at 4c000000 ...
Android image found
kernel size: 85b9d1
kernel address: 48080000
ramdisk size: 54ddbc
ramdisk addrress: 4a180000
second size: 0
second address: 48000800
tags address: 48000100
page size: 800
os_version: 1200012a (ver: 0.9.0, level: 2018.10)
name:
cmdline: buildvariant=userdebug
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
It is possible for this to happen if something goes wrong very early in
the init sequence. Add a check for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if one of the initcalls fails on sandbox the address printing
is not help, e.g.:
initcall sequence 0000557678967c80 failed at call 00005576709dfe1f (err=-96)
This is because U-Boot gets relocated high into memory and the relocation
offset (gd->reloc_off) does not work correctly for sandbox.
Add support for finding the base address of the text region (at least on
Linux) and use that to set the relocation offset. This makes the output
better:
initcall sequence 0000560775957c80 failed at call 0000000000048134 (err=-96)
Then you use can use grep to see which init call failed, e.g.:
$ grep 0000000000048134 u-boot.map
stdio_add_devices
Of course another option is to run it with a debugger such as gdb:
$ gdb u-boot
...
(gdb) br initcall.h:41
Breakpoint 1 at 0x4db9d: initcall.h:41. (2 locations)
Note that two locations are reported, since this function is used in both
board_init_f() and board_init_r().
(gdb) r
Starting program: /tmp/b/sandbox/u-boot
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".
U-Boot 2018.09-00264-ge0c2ba9814-dirty (Sep 22 2018 - 12:21:46 -0600)
DRAM: 128 MiB
MMC:
Breakpoint 1, initcall_run_list (init_sequence=0x5555559619e0 <init_sequence_f>)
at /scratch/sglass/cosarm/src/third_party/u-boot/files/include/initcall.h:41
41 printf("initcall sequence %p failed at call %p (err=%d)\n",
(gdb) print *init_fnc_ptr
$1 = (const init_fnc_t) 0x55555559c114 <stdio_add_devices>
(gdb)
Signed-off-by: Simon Glass <sjg@chromium.org>
When using boot scripts it can become quite hard to understand
which commands are actually executed during bootup (e.g. where
is a kernel image loaded from or which DTB is in use).
Shell scripts suffer from a similar problem and many shells address
this problem with a command execution tracer (e.g. BASH has xtrace,
which can be enabled by "set -x").
This patch introduces a command tracer for U-Boot, which prints
every command with its arguments before it is executed.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Our platform doesn't store the DTB into the Android image second area,
but rather copies the DTB to RAM from a dedicated dtb.img partition [0],
prior to booting the Android image by calling bootm.
Similar to [1], we find it useful to just call 'bootm' and have the
right DTB being passed to OS (assuming its address has been previously
stored in 'fdtaddr' by calling `fdt addr <dtb-addr>`).
Booting Android with DTB from 'fdtaddr' will only occur if:
- No DTB is embedded in the second area of Android image
- 'fdtaddr' points to a valid DTB in RAM
[0] https://source.android.com/devices/architecture/dto/partitions
[1] https://patchwork.ozlabs.org/patch/1046652/
("Support boot Android image without address on bootm command")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prepare for booting Android images which lack any DTB in the second
area by using 'fdtaddr' environment variable as source/address of FDT.
No functional/behavioral change expected in this patch.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Increase the readability of boot_get_fdt().
No change in behavior is expected.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'no_fdt' goto label was introduced by v2015.01 commit [0] and it
had two review stages [1-2]. The *documented* purpose behind commit [0]
is (excerpt from commit description):
> allows both FDT and non-FDT kernels to boot by making the
> third parameter to the bootm/bootz optional
While [1] and [2] share the same goal, they have very different
implementations:
- [1] was based on a very simple 'argc' check at function error out
with returning success to the caller if the third parameter was NOT
passed to bootm/bootz command. This approach had the downside of
returning success to the caller even in case of legitimate internal
errors, which should halt booting.
- [2] added the "no_fdt" label and several "goto no_fdt" statements.
This allowed to report the legitimate internal errors to the caller.
IOW the major difference between [1] and [2] is:
- [1] boot w/o FDT if FDT address is not passed to boot{m,z,*}
- [2] give *freedom* to the developer to boot w/o FDT from any
(more or less) arbitrary point in the function flow (and here
comes the peculiar aspect, which looks to be a leftover from [1])
with the precondition that the 3rd argument (FDT address) is NOT
provided to boot{m,z,*}. In practice, this means that only a subset
of "goto no_fdt" end up booting w/o FDT while the other subset is
returning an error to the caller.
This patch removes the peculiar behavior described above, such that
"goto no_fdt" performs really what it tells to the developer.
The motivation of this patch is to decrease the unneeded complexity
and increase the readability of boot_get_fdt().
[0] 48aead71c1 ("fdt: Allow non-FDT kernels to boot when CONFIG_OF_LIBFDT is defined")
[1] https://patchwork.ozlabs.org/patch/412923/
("[U-Boot,v1] fdt: Allow non-FDT kernels to boot when CONFIG_OF_LIBFDT is defined")
[2] https://patchwork.ozlabs.org/patch/415635/
("[U-Boot,v2] fdt: Allow non-FDT kernels to boot when CONFIG_OF_LIBFDT is defined")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Paranoid programming [1] lies at the foundation of proper software
development, but the repetitive zeroing-out of output arguments in the
context of the same function rather clutters the code and inhibits
further refactoring/optimization than is doing any good.
In boot_get_fdt(), we already perform zero/NULL-initialization of
*of_flat_tree and *of_size at the beginning of the function, so doing
the same at function error-out is redundant/superfluous.
Moreover, keeping the code unchanged might encourage the developers to
update *of_flat_tree and *of_size during some interim computations,
which is against the current design of boot_get_fdt(). Currently,
writing useful data into these arguments happens just before
successfully returning from boot_get_fdt() and it should better stay so.
[1] https://blog.regehr.org/archives/1106
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The cache flush of the kernel load area needs to be aligned outward to
the DMA cache alignment. The operations are simpler if we think of this
as aligning the start down, ALIGN_DOWN(load, ARCH_DMA_MINALIGN), and
aligning the end up, ALIGN(load_end, ARCH_DMA_MINALIGN), and then find
the length of the flushed region by subtracting the former from the
latter.
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using memalign() in a scenario where U-Boot is configured for full
malloc support with simple malloc not explicitly enabled and before the
full malloc support is initialized, a memory block is being allocated
and returned without the alignment parameter getting honored.
Fix this issue by replacing the existing memalign pre-full malloc init
logic with a call to memalign_simple() this way ensuring proper alignment
of the returned memory block.
Fixes: ee038c58d5 ("malloc: Use malloc simple before malloc is fully initialized in memalign()")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds a short message to the SPL NAND loader, which displays
the source and destinations addresses including the size of the
loaded image, like this:
U-Boot SPL 2019.04-rc3-00113-g486efd8aaf (Mar 15 2019 - 14:18:02 +0100)
Trying to boot from NAND
Loading U-Boot from 0x00040000 (size 0x000a0000) to 0x22900000
I find this message quite helpful - hopefully others do so as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for loading fully featured fitImages over YModem in SPL.
This is useful when various advanced features of full fitImages are
needed in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Currently only the first fdt is loaded from the extra configuration of
FIT image.
If the configuration have multiple fdt, load them all as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
It works perfectly fine to boot an Android boot.img with bootm command
followed by an explicit address argument that holds the image. But if
we have boot.img downloaded into default 'loadaddr', and then boot it
using bootm command without the address argument, we will run into
problem, because U-Boot fails to find ramdisk and fdt (second area) in
boot.img.
The current Android image support assumes there is always an address
argument on bootm command. However just like booting any other images,
'loadaddr' should be used when address argument is missing from bootm
command. It patches boot_get_ramdisk() and boot_get_fdt() a bit to
support this quite common usage of bootm command for Android image.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
-----BEGIN PGP SIGNATURE-----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=QdJl
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (2)
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
- bug fix for ASCII characters > 127
- ANSI sequence handling extensions (implement clear line,
reverse video and relative cursor movement commands)
- preparation for doing character set translations
- left/right and up/down arrow keys translation to ANSI
control sequences for cursor movement to fix selection
with an USB keyboard in bootmenu
- CONFIG_SYS_WHITE_ON_BLACK font scheme configuration for
sunxi boards
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXLN1fg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXJKfAJ4mlkJRm5oXcjjZqVkI+Qm1NdKpPACfUuvrDOgo
MzubX1rLQS+h8BBlG+s=
=7pd3
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.07-rc1' of git://git.denx.de/u-boot-video
- optional backlight PWM polarity config via polarity cell
- bug fix for ASCII characters > 127
- ANSI sequence handling extensions (implement clear line,
reverse video and relative cursor movement commands)
- preparation for doing character set translations
- left/right and up/down arrow keys translation to ANSI
control sequences for cursor movement to fix selection
with an USB keyboard in bootmenu
- CONFIG_SYS_WHITE_ON_BLACK font scheme configuration for
sunxi boards
So far arrows key pressed on an USB keyboard got translated to some
low ASCII control sequences (Ctrl+N, Ctrl+P). Some programs understand
these codes, but the standard for those keys is to use ANSI control
sequences for cursor movement (ESC [ A).
Our own boot menu is a victim of this, currently we cannot change the
selection with an USB keyboard due to this.
Since we already implement a queue for USB key codes, we can just insert
the three character ANSI sequence into the key buffer. This fixes the
bootmenu, and is more universal for other users (UEFI) as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The first functions of the UEFI sub-system are invoked before reaching the
U-Boot shell, e.g. efi_set_bootdev(), efi_dp_from_name(),
efi_dp_from_file(). We should be able to print out device paths for
debugging purposes here.
When printing device paths via printf("%pD\n", dp) this invokes functions
defined as EFIAPI. So efi_save_gd() must be called beforehand.
So let's move the efi_save_gd() call to function initr_reloc_global_data(()
in board_r.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 6d29cc7dcf ("fdt: Fixup only valid memory banks") ended up
being merged twice, first as:
commit 6d29cc7dcf
Author: Thierry Reding <treding@nvidia.com>
AuthorDate: Tue Jan 30 11:34:17 2018 +0100
Commit: Simon Glass <sjg@chromium.org>
CommitDate: Sun Feb 18 12:53:38 2018 -0700
fdt: Fixup only valid memory banks
Memory banks with address 0 and size 0 are empty and should not be
passed to the OS via device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
and later again, though this time it was v2:
commit ed5af03f9b
Author: Thierry Reding <treding@nvidia.com>
AuthorDate: Thu Feb 15 19:05:59 2018 +0100
Commit: Tom Rini <trini@konsulko.com>
CommitDate: Fri Feb 23 10:40:50 2018 -0500
fdt: Fixup only valid memory banks
Memory banks with address 0 and size 0 are empty and should not be
passed to the OS via device tree.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The second version was slightly different, so the main hunk of the patch
was applied twice. This isn't harmful because the code is idempotent,
but it's wasteful to run the same code twice.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case the gunzip() call fails, it will print an error message.
If that happens within the YModem session, the error message will
not be displayed and would be useless. Move the gunzip() call out
of the YModem session to make those possible error messages visible.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
In case spl_parse_image_header() errors out, terminate the YModem
session, otherwise we won't get any further output.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Current code is plain wrong, and there's no need to have a mutable string,
so fix function type and remove the intermediate variable.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
If FIT_IMAGE_TINY is enabled, spl_fit_image_get_os returns -ENOTSUPP.
In this case, we should default to IH_OS_U_BOOT not to IH_OS_INVALID.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Handle in boot_fdt_reserve_region
any return value > 0 of lmb_reserve() function;
it occurs when coalesced region are found:
adjacent reserved region are merged.
This patch avoid the error trace:
ERROR: reserving fdt memory region failed..
when reserved region are merged (return value = 1).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
To find out how big the early malloc heap must be in SPL, add a debug
print statement that dumps its usage before switching to relocated heap
in spl_relocate_stack_gd() via CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This is the same migration path as commit b6251db8c3 ("Kconfig:
Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND").
I also moved the description in README to the Kconfig help.
I ripped off the sentence about 'LWMON' since it is gone already.
I only let my boards migrate, leaving the rest to platform maintainers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present the default log level is set to LOGL_INFO on start-up. Allow
this to be controlled from Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The log level numbers in the Kconfig are not actually correct. Fix them
and also add a missing space in the header-file comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
SPL currently does not check uImage CRCs when loading U-Boot.
This patch adds checking the uImage CRC when SPL loads U-Boot. It does
this by reusing the existing config option SPL_CRC32_SUPPORT to allow
leaving out the CRC check on boards where the additional code size or
boot time is a problem (adding the CRC check currently adds ~1.4 kByte
to flash).
The SPL_CRC32_SUPPORT config option now gets enabled by default if SPL
support for legacy images is enabled to check the CRC on all boards
that don't actively take countermeasures.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since there is the SPL_USB_HOST_SUPPORT for enabling USB support in SPL,
makes more sense to rename the SPL_USB_SUPPORT as SPL_USB_STORAGE.
Everything that is not part of the usb storage support in SPL is now
build under SPL_USB_HOST_SUPPORT.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
This converts the following to Kconfig:
CONFIG_BOARD_TYPES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The board_r init function was complaining that we are looping through
an array, calling all our tiny init stubs sequentially via indirect
function calls (which can't be speculated, so they are slow).
The solution to that is pretty easy though. All we need to do is inline
the function that loops through the functions and the compiler will
automatically convert almost all indirect calls into direct inlined code.
With this patch, the overall code size drops (by 40 bytes on riscv64)
and boot time should become measurably faster for every target.
Signed-off-by: Alexander Graf <agraf@suse.de>
Some platforms choose to store device tree blob in Android image second
area. Let's try to look for dtb from there when booting an Android
image, and use it for booting if found.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SPL only needs to be able to read from SPI Flash to load next stage and
does not really need write/erase etc. Therefore in order to reduce SPI
Flash code size in SPL, enable SPI_FLASH_TINY, that only supports
reading from SPI flash, as default.
Note: Since, SPI_FLASH_TINY does not support SPI_FLASH_BAR,
SPI_FLASH_TINY is not enabled for boards with SPI controllers that
cannot support 4 byte addressing.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from
Linux. This allows auto detection and configuration of Flash parameters.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
This fixes the automatic lmb initialization and reservation for boards
with more than one DRAM bank.
This fixes the CVE-2018-18439 and -18440 fixes that only allowed to load
files into the firs DRAM bank from fs and via tftp.
Found-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most of the time SPL only needs very simple FAT reading, so having
CONFIG_IS_ENABLED(FAT_WRITE) to exclude it from SPL build would help
to save 64KiB default max clustersize from memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
CLI support with the HUSH parser is not currently SPL safe due to it's
use of realloc. That function is not defined for SPLs that use
SYS_MALLOC_SIMPLE. CLI support can be built in to SPL and some functions
do work, but use of some like run_command() will cause build to fail.
When no SPL code calls this function build works as the compiler removes
this unreachable code so the unresolved symbols are ignored.
If DFU support is enabled in SPL then MMU DFU support may get brought in
also, this code does make a call to run_command() causing build to fail
if the HUSH parser is not built-in. To break this odd and unneeded
dependency chain we use CONFIG_IS_ENABLED where appropriate to prevent
calls into HUSH code from SPL. This also removes our need to pull in the
rather unrelated source file when SPL_DFU is defined.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
boot_fdt_add_mem_rsv_regions() adds reserved memory sections to an lmb
struct. Currently, it only parses regions described by /memreserve/
entries.
Extend this to the more commonly used scheme of the "reserved-memory"
node.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlw+AlIACgkQfxc6PpAI
reYchAf+L/P5JsLoCKAY84v11eWQkCS44idAYStD8Q023dyuyNC/W6G3qEQVGkHu
SXBzNrZ5wSJanN5I3h3ktJ7yfMOYIvSO2qLHphxDstPaZbCY4Zac6NywHrHxQpA9
fbSilQRbcVWrPo5rsjjZhXmMdQRZVOmGD6CYZj1AihWAiHfYth7f6laNWNTWQA8C
z+aoiF70t/PbvwFbgdzzYOjoGdXI9XML0xTqdLWRlsBKjf3z54pCV6LmN2xrsrDZ
k7lr+x7ajJUFhivxzjowf4aOjhDB+/+I3sr+hJ5vkMM0Kqg14bbEU+xJRGpDc18K
QPvVHT5JGe/nq1cZXuCqzrYxTrrA7A==
=w9ln
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15jan19' of git://git.denx.de/u-boot-dm
Fix recent changes to serial API for driver model
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
Add the dollar_complete() function to auto-complete arguments starting
with a '$' and use it in the cmd_auto_complete() path such that all
args starting with a $ can be auto-completed based on the available env
vars.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Fix some linking problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
The repeatable property is currently attached to the main command and
sub-commands have no way to change the repeatable value (the
->repeatable field in sub-command entries is ignored).
Replace the ->repeatable field by an extended ->cmd() hook (called
->cmd_rep()) which takes a new int pointer to store the repeatable cap
of the command being executed.
With this trick, we can let sub-commands decide whether they are
repeatable or not.
We also patch mmc and dtimg who are testing the ->repeatable field
directly (they now use cmd_is_repeatable() instead), and fix the help
entry manually since it doesn't use the U_BOOT_CMD() macro.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some commands have a table of sub-commands. With minor adjustments,
complete_cmdv() is able to provide auto-completion for sub-commands
(it's just about passing the table of commands instead of taking the
global one).
We rename this function into complete_subcmd() and implement
complete_cmdv() as a wrapper around complete_subcmdv().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When auto-completing command arguments, the last argument is not
necessarily the one we need to auto-complete. When the last character is
a space, a tab or '\0' what we want instead is list all possible values,
or if there's only one possible value, place this value on the command
line instead of trying to suffix the last valid argument with missing
chars.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 2c77c0d652 ("xyz-modem: Change getc timeout loop waiting")
fixes the loop delay when using a hw watchdog, assuming that watchdog
kicking is taken care of by getc(). But the xyzmodem driver tries to
do a getc only after confirming that a character is available like below:
while (!tstc()) {
till timeout;
}
if (tstc())
*c = getc();
and getc() does a watchdog reset only if it fails to see a character.
In this case, getc() always sees a character and never does a
watchdog reset. So to make sure that watchdog doesn't get reset
while loading the file, do a watchdog reset just before starting the
image loading.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for gunzip-ing gzip-compressed uImages in the SPL Ymodem code.
Loading data over Ymodem can be gruelingly slow, gzip-ing the data can
reduce that aggravating slowness at least slightly (depends on the data,
u-boot.bin compresses to ~1/3 of it's original size on ARM64), hence add
optional support for decompressing gzip-compressed uImages.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
We usually deal with hexadecimal addresses and sizes in
device-tree. Its much easier if debug logs print hexadecimal
values too.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Booting an image currently sets the environment variable "fdtaddr"
by calling into 'cmd/fdt.c'. As a result, linking U-Boot fails if
CMD_FDT is not enabled.
Fix this by adding 'if (CONFIG_IS_ENABLED(CMD_FDT))' to the two
places where 'set_working_fdt_addr()' is called.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If we don't define CONFIG_SPL_FIT_IMAGE_TINY, when loading images from FIT,
the SPL will record all loadables' info to u-boot's FDT. This causes
problem when HAB is enabled, because FDT's content is modified before
we authenticate it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8M bootable image type is like i.MX6/7, but there is signed HDMI
firmware image in front of A53 bootable image, which is also has an IVT
header.
Here we also include fit image to generate a bootable image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If DM_USB_GADGET is used, the usb ethernet gadget driver must be bound to a
controller before the image can be downloaded over the network.
In u-boot this can be done with the bind command. In SPL it must be done
programmatically.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Building U-Boot with CONFIG_PCI and CONFIG_DM_PCI enabled, but
CONFIG_SPL_PCI_SUPPORT disabled, results in following linker
error:
lib/built-in.o: In function `fdtdec_get_pci_bar32':
lib/fdtdec.c:305: undefined reference to `dm_pci_read_bar32'
fdtdec.c:305:(.text.fdtdec_get_pci_bar32+0x24): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `dm_pci_read_bar32'
This is because reference to dm_pci_read_bar32() remains in lib/fdtdec.c
while SPL build does not descend into drivers/pci directory in
drivers/Makefile if CONFIG_SPL_PCI_SUPPORT is not enabled.
Fix this by applying appropriate #define guards in lib/fdtdec.c.
It looks like ns16550.c has the same problem, so fixed that too.
To simplify this, CONFIG_SPL_PCI_SUPPORT is renamed to CONFIG_SPL_PCI
(enables use of CONFIG_IS_ENABLED() macro).
Suggested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function part_init() will only be built when we have both
CONFIG_PARTITIONS and CONFIG_HAVE_BLOCK_DEVICE set. Protect the call to
this function with both of these tests now.
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The CRC16-CCITT checksum function is useful for space-constrained
applications (such as obtaining a checksum across a 2KBit or 4KBit
EEPROM) in boot applications. It has not been accessible from boot
scripts until now (due to not having a dedicated command and not being
supported by the hash infrstructure) limiting its applicability
outside of custom commands.
This adds the CRC16-CCITT (poly 0x1021, init 0x0) algorithm to the
list of available hashes and adds a new crc16_ccitt_wd_buf() to make
this possible.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Fix building crc16.o for SPL/TPL]
Signed-off-by: Tom Rini <trini@konsulko.com>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Drop BMP_ALIGN_CENTER define in lcd.c and video_bmp.c as it is
already defined by splash.h. Include splash.h in bmp code.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add common clear screen command for configurations
CONFIG_DM_VIDEO, CONFIG_LCD and CONFIG_CFB_CONSOLE.
Remove the existing cls command implementation from
lcd.c code and activate the command for all boards
enabling CONFIG_LCD for compatibility reasons.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Patrick.Delaunay <patrick.delaunay@free.fr>
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
CC common/board_r.o
common/board_r.c:747:2: error: ‘initr_spi’ undeclared here (not in a function)
initr_spi,
^
make[1]: *** [common/board_r.o] Error 1
Fixes: ebe76a2df9 ("dm: Remove spi_init() from board_r.c when using driver model")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
We add the support of the padding pss for rsa signature.
This new padding is often recommended instead of pkcs-1.5.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rsa signature use a padding algorithm. By default, we use the
padding pkcs-1.5. In order to add some new padding algorithm, we
add a padding framework to manage several padding algorithm.
The choice of the padding is done in the file .its.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the sandbox the memory addresses in the device tree refer to the virtual
address space of the sandbox. This implies that the memory reservations for
the fdt also have to be converted to this address space.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The sandbox uses a virtual address space that is neither the physical nor
the virtual address space of the operating system. All address used on the
command line live in this address space. So also the environment variable
${fdtcontroladdr} has to be in this address space.
Commands like bootefi and booti receive the fdt address as parameter.
Without the patch ${fdtcontroladdr} cannot be used as parameter value on
the sandbox.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
It is sometimes useful to see what memory is being allocated early during
boot. Add logging to support this, using a new LOGC_ALLOC category.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for MTK boot image generation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In legacy CONFIG_HARD_SPI initalizing spi_init code, which
was removed during dm conversion cleanup.
So remove the dead instances of CONFIG_HARD_SPI, and related
code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- spi_init_f
- spi_init_r
- spi_read
- spi_write
these spi calls are exclusively for mpc8xx, but
the relevant driver is not available so remove it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
spi_init used in some areas in tree, but the respective
drivers will remove in future patches.
So remove the same instances.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This fixes link issues when building the SPL without USB driver model
but with USB storage support. CONFIG_BLK can be enabled and disabled
independently for SPL and non-SPL builds. We leverage that existing
functionality here.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This allows to disable the USB driver model in SPL because it checks
the CONFIG_SPL_DM_USB variable for SPL builds. Nothing changes for
regular non-SPL builds.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Common USB code is built whenever USB is enabled (in non-SPL builds).
The USB uclass is built whenever (SPL_)DM_USB is enabled. Both need to
be independent from CMD_USB.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
There is some basic informaton that SPL normally wants to pass through to
U-Boot, such as the SDRAM size and bank information.
Mkae use of the new bloblist structure for this. Add a new 'handoff' blob
which is set up in SPL and passed to U-Boot proper. Also adda test for
sandbox_spl that checks that this works correctly and a new 'sb' command
to show the information passed from SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
We support putc() in this case but not puts(), but this is more useful
since it is what printf() uses.
This particularly affects debugging early in SPL, where currently printf()
statements result in no output. Fix this by adding a special case into
puts() for sandbox, just like putc().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
There is a strange feature to set global_data to a data-section variable
early in SPL. This only works if SPL actually has access to SRAM which is
not the case on x86, for eaxmple. Add a comment to this effect.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having a negative option, make this a positive option and
enable it by default. This makes it easier to understand.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use a macro rather than hard-coding the SPL prompt to 'spl'
since the code can be used by TPL too. Add a macro that works for both
and use it in various places.
This allows TPL to use the same code without printing confusing messages.
Note that the string is lower case ('spl', 'tpl') which is a change from
previously.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these subsystems are only supported in U-Boot proper but it is
sometimes necessary to support them in SPL, or even TPL. Update the
Kconfig and Makefile to support this. Also adjust GPIO so that it can be
used in TPL if required.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for locating a bloblist in U-Boot that has been set up by SPL.
It is copied into RAM during relocation.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The bloblist is normally set up in SPL ready for use by U-Boot. Add
a simple implementation of this to the common SPL code.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is no standard way in U-Boot to pass information from SPL
to U-Boot proper. But sometimes SPL wants to convey information to U-Boot
that U-Boot cannot easily figure out. For example, if SPL sets up SDRAM
then it might want to pass the size of SDRAM, or the location of each
bank, to U-Boot proper.
Add a new 'bloblist' feature which provides this. A bloblist is set up in
the first phase of U-Boot that runs (i.e. TPL or SPL). The location of
this info may be in SRAM or CAR (x86 cache-as-RAM) or somewhere else.
Information placed in this region is preserved (with a checksum) through
TPL and SPL and ends up in U-Boot. At this point it is copied into SDRAM
so it can be used after relocation.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
It is sometimes useful to log information in SPL and TPL. Add support for
this.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these features are supported in SPL but not TPL. Update the
Kconfig and Makefile to allow this.
Also add a few Makefile comments to make earier to track what is going on.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is really just a call to uclass_get_device() and there is no
reason why the caller cannot do it. Update sandbox and snow accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
A specially crafted FIT image leads to memory corruption in the stack
when using the verified boot feature. The function fit_config_check_sig
has a logic error that makes it possible to write past the end of the
stack allocated array node_inc. This could potentially be used to bypass
the signature check when using verified boot.
This change ensures that the number of strings is correct when counted.
Signed-off-by: Konrad Beckmann <konrad.beckmann@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.
Update all DM BLK drivers to adopt this change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It was observed that current output of print_cpuinfo() on QEMU
x86 targets does not have an ending '\n', neither have a leading
'CPU:' any more. However it used to have these before.
It turns out commit c0434407b5 introduced a unified DM version
of print_cpuinfo() that exposed such issue on QEMU x86.
Fixes: c0434407b5 ("board_f: Use static print_cpuinfo if CONFIG_CPU is active")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the DM CPU drivers are active, printing information about a CPU
should be delegated to a matching driver.
Hence, add a static print_cpuinfo that implements this delegation when
DM CPU drivers are active.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Changed condition to CONFIG_IS_ENABLED(CPU):
Signed-off-by: Simon Glass <sjg@chromium.org>
common/common_fit.c is including <spl.h>, but not actually using it. The
inclusion will cuase compile error on platforms using CONFIG_OF_SEPARATE
and not SPL.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tiny printf does not support %.*s and %lX. Since tiny printf should
be very common in SPL, replace these by %32s (for printing image
name) and %lx.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit c0434407b5.
It turns out commit c0434407b5 broke some boards which have DM CPU
driver with CONFIG_DISPLAY_CPUINFO option on. These boards just fail
to boot when print_cpuinfo() is called during boot.
Fixes are already sent to ML and in u-boot-dm/next, however since
we are getting close to the v2018.11 release, it's safer we revert
the original commit.
This commit should be reverted after v2018.11 release.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In upcoming freescale board LX2160AQDS, the MDIO bus is muxed.
i.e. same MDIO bus can be routed to eight different slots depending
on mux register settings.
To support this mdio mux behavior, we add each MDIO bus mux as a
separate MDIO bus.
Now, various phy devices can be attached to each of these slots(mux).
The information about these devices is passed to OS via device tree.
To do the fdt fixups related to MDIO bus, its necessary that MDIO bus
list is accessed.Therefore, add a function to retrieve the list head.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
i.MX8/8X bootable image type is container type.
The bootable image, containers a container set which supports two
container. The 1st container is for SECO firmware, the 2nd container
needs to include scfw, m4_0/1 image, ACore images per your requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch partially reverts:
"spl: fit: Add support for loading FPGA bitstream"
(sha1: 26a642238b)
There shouldn't be a need to call private spl_load_fpga_image function
because the whole sequence should be already handled by fpga framework.
If there is missing loading bistream by chunks it should be done via
fpga framework instead of having private hooks.
Also spl_load_fpga_image() weak function is not used anywhere and
opening a way for not reviewed hacks out of mainline U-Boot is not the
right way to go.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sandbox SPL/TPL support
Various dm-related improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
/b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
=Bfjm
-----END PGP SIGNATURE-----
Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
Add board-specific hook which is executed before the code hands over
control to the OS. This lets the board perform some last-minute clean
ups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
It is useful to be able to set the default log level from the command line
when running sandbox. Add a new -L command-line flag for this. The log
level is set using the enum log_level_t in log.h. At present a number must
be specified, e.g. -L7 for debug.
Signed-off-by: Simon Glass <sjg@chromium.org>
With CONFIG_OPTEE_TA_AVB use the trusted application AVB provided by
OP-TEE to manage rollback indexes and device-lock status.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
The patch:
"spl: Weed out CONFIG_SYS_TEXT_BASE usage"
(sha1: 04ce5427bd)
introduced bug where assigning to u_boot_pos variable wasn't done
which end up in situation where SPL wasn't able to find out
image on the selected address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of manually specifying CONFIG_SYS_EXTRA_ENV_RELOC
for every board that needs it, it shouldn't hurt to let
initr_reloc_global_data() always relocate gd->env_addr
unless we know this pointer is outside the initial binary.
To achieve this, the relocation is omitted if
CONFIG_ENV_ADDR is defined (and ENV_IS_EMBEDDED is not).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbt0FOAAoJECaAFcEOcohNZmcH/A1mKO0/R4tHCqFP2j0I+OuP
PClkA1HUZuD5phvPMaxdHQBwsq7sAa8AljK1oPCNkslP7mFxToUUBx7xc0vB89P/
D+XsI4uce89hIyTULR2FdhR22MOk41zaLVeNicpQ1keCNbzCwsHsHTA+B4XN/xNe
tdPpu6wN2D+g88DAv+/ebVYgjmxRvFD4qpL9bbZpOqqA8XCcD31ukCR2E4fsESgn
mzwKaKcX6SeYgTVCT8Q15SLTNI1WRUY1Y1laj1WKl4abY+HsTt4Whm9imM2l3K5W
ODj6vnFlwEC9rgdxmtXGcmBfwtyXubSfuZDrMGFAiOlyIUgpPXWZI7i8LYQbZ7s=
=NdBl
-----END PGP SIGNATURE-----
Merge tag 'rockchip-for-v2018.11-rc2' of git://git.denx.de/u-boot-rockchip
Rockchip-focused changes for v2018.11-rc2:
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
Signed-off-by: Tom Rini <trini@konsulko.com>
With implemented print_cpuinfo() and model property in .dts
we're ready to print nice info about ARC cores and boards on boot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
OP-TEE is an open source trusted OS, in armv7, its loading and
running are like this:
loading:
- SPL load both OP-TEE and U-Boot
running:
- SPL run into OP-TEE in secure mode;
- OP-TEE run into U-Boot in non-secure mode;
To make code simple, it would be fine to use IH_OS_TEE for the
os tyle in TPL(just like IH_OS_LINUX is using both in SPL and U-Boot).
Here is the diagram for SPL loading OP-TEE,
IH_OS_TEE:(make u-boot.itb for SPL)
Non-Secure Secure
BootROM
|
v
SPL
|
v
--------- OP-TEE
|
v
U-Boot
|
V
Linux
For other two king of OP-TEE loading/booting, see commit message:
45b55712d4 image: Add IH_OS_TEE for TEE chain-load boot
More detail:
https://github.com/OP-TEE/optee_os
and search for 'boot arguments' for detail entry parameter in:
core/arch/arm/kernel/generic_entry_a32.S
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
If we fail to find the MMC boot device, report the number of the one
we were looking for in the error to aid diagnosis.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ZuJG
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
When running sandbox with the new pointer sanitization we just recently
introduced, we're running into a case with FIT images where we end up
interpreting pointers as addresses.
What happened is that most callers of set_working_fdt_addr() simply
convert pointers into addresses without taking into account that they
might be 2 separate address spaces. Fix the callers up to map their
pointers into addresses.
This makes sandbox tests pass for me again.
Signed-off-by: Alexander Graf <agraf@suse.de>
There is no reason to limit gzip usage only for OS_BOOT and kernel image
type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: York Sun <york.sun@nxp.com>
The SPL loaders assume that the CONFIG_SYS_TEXT_BASE memory location
is available and can be corrupted by loading ie. uImage or fitImage
headers there. Sometimes it could be beneficial to load the headers
elsewhere, ie. if CONFIG_SYS_TEXT_BASE is not yet writable while we
still want to parse the image headers in some local onchip memory to
ie. extract firmware from that image.
Add the possibility to override the location where the headers get
loaded by introducing new function, spl_get_load_buffer() which takes
two arguments -- offset from the CONFIG_SYS_TEXT_BASE and size of the
data that are to be loaded there -- and returns a valid buffer address
or hangs the system. The default behavior is the same as before, add
the offset to CONFIG_SYS_TEXT_BASE and return that address. User can
override the weak spl_get_load_buffer() function though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When the DM CPU drivers are active, printing information about a CPU
should be delegated to a matching driver.
Hence, add a static print_cpuinfo that implements this delegation when
DM CPU drivers are active.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Changed condition to CONFIG_IS_ENABLED(CPU):
Signed-off-by: Simon Glass <sjg@chromium.org>
To print the reset status during boot, add a method print_resetinfo to
board_f, which is called in init_sequence_f[], that gets the reset
information from the sysreset driver (assuming there is only one seems
reasonable), and prints it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Unify the fgetc function when MUX is activated or not:
- always call tstc() : it is the normal behavior expected
by serial uclass (call tstc then getc) and that avoids
issue when SERIAL_RX_BUFFER is activated
- reload WATCHDOG in the char waiting loop
This patch allow to have the same behavior when CONSOLE_MUX is activated
or not and avoid regression when this feature is deactivated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
malloc_simple() can return 0 if out of memory. Don't call memset
from calloc() in this case but rely on the caller checking
the return value.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Compiling U-Boot with ubsan/asan libraries and running it in sandbox
may lead to below backtrace:
=> avb init 0
=> avb verify
## Android Verified Boot 2.0 version 1.1.0
read_is_device_unlocked not supported yet
common/avb_verify.c:407:31: runtime error: division by zero
AddressSanitizer:DEADLYSIGNAL
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
=================================================================
==9388==ERROR: AddressSanitizer: FPE on unknown address 0x0000004b467f \
(pc 0x0000004b467f bp 0x000000000000 sp 0x7ffd899fe150 T0)
#0 0x4b467e in mmc_byte_io common/avb_verify.c:407
#1 0x4b4c47 in mmc_byte_io common/avb_verify.c:532
#2 0x4b4c47 in read_from_partition common/avb_verify.c:533
#3 0x69dc0d in load_and_verify_vbmeta lib/libavb/avb_slot_verify.c:560
#4 0x6a1ee6 in avb_slot_verify lib/libavb/avb_slot_verify.c:1139
#5 0x45dabd in do_avb_verify_part cmd/avb.c:245
#6 0x4af77c in cmd_call common/command.c:499
#7 0x4af77c in cmd_process common/command.c:538
#8 0x46bafc in run_pipe_real common/cli_hush.c:1677
#9 0x46bafc in run_list_real common/cli_hush.c:1875
#10 0x46c780 in run_list common/cli_hush.c:2024
#11 0x46c780 in parse_stream_outer common/cli_hush.c:3216
#12 0x46d34b in parse_file_outer common/cli_hush.c:3299
#13 0x4ad609 in cli_loop common/cli.c:217
#14 0x4625ae in main_loop common/main.c:65
#15 0x46f2d1 in run_main_loop common/board_r.c:648
#16 0x640253 in initcall_run_list lib/initcall.c:30
#17 0x46f9d0 in board_init_r common/board_r.c:879
#18 0x40539b in main arch/sandbox/cpu/start.c:321
#19 0x7fa94925f82f in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2082f)
#20 0x408908 in _start (/srv/R/u-boot-master/u-boot+0x408908)
AddressSanitizer can not provide additional info.
SUMMARY: AddressSanitizer: FPE common/avb_verify.c:407 in mmc_byte_io
==9388==ABORTING
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cppcheck (v1.85) reports w/o this patch:
[common/avb_verify.c:738] -> [common/avb_verify.c:741]: (warning) \
Either the condition 'ops' is redundant or there is possible null \
pointer dereference: ops.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fix sparse complaint:
common/avb_verify.c:14:21: warning: \
symbol 'avb_root_pub' was not declared. Should it be static?
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fix below compiler [1] warning:
common/avb_verify.c: In function ‘avb_find_dm_args’:
common/avb_verify.c:179:30: warning: left-hand operand of comma expression has no effect [-Wunused-value]
for (i = 0; i < AVB_MAX_ARGS, args[i]; ++i) {
[1] aarch64-linux-gnu-gcc (Linaro GCC 7.2-2017.11)
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
dtimg command allows user to work with Android DTB/DTBO image format.
Such as, getting the address of desired DTB/DTBO file, printing the dump
of the image in U-Boot shell, etc.
This command is needed to provide Android boot with new Android DT image
format further.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Android documentation recommends new image format for storing DTB/DTBO
files: [1]. To support that format, this patch adds helper functions for
Android DTB/DTBO format. In image-android-dt.* files you can find helper
functions to work with Android DT image format, such us routines for:
- printing the dump of image structure
- getting the address and size of desired dtb/dtbo file
This patch uses dt_table.h file, that was added in commit 643cefa4d8
("Import Android's dt_table.h for DT image format") by Alex Deymo.
[1] https://source.android.com/devices/architecture/dto/partitions
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
spl_common_init() debug-prints "spl_early_init()\n" but it is
called both from spl_early_init() and spl_init().
Fix this by moving the debug() statement to the calling functions
which now print their name.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Replaced misspelled words "parition"/"paritioning" (missing 't') in two
Kconfig files by correct words "partition"/"partitioning"
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If CONFIG_NR_DRAM_BANKS is bigger than the default
value (4) define MEMORY_BANKS_MAX as CONFIG_NR_DRAM_BANKS.
Fixes: 2a1f4f1758 ("Revert "fdt_support: Use CONFIG_NR_DRAM_BANKS if defined"")
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Implement get_size_of_partition() operation,
which is required by the latest upstream libavb [1].
[1] https://android.googlesource.com/platform/external/avb/+/android-p-preview-5
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Initialize the led with the default state defined in device tree
in board_init and solve issue with test for led default state.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
These functions are only called in this file that's why make them static
to keep static analysers happy.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present each entry has an offset within its parent section. This is
useful for figuring out how entries relate to one another. However it
is sometimes necessary to locate an entry within an image, regardless
of which sections it is nested inside.
Add a new 'image-pos' property to provide this information. Also add
some documentation for the -u option binman provides, which updates the
device tree with final entry information.
Since the image position is a better symbol to use for the position of
U-Boot as obtained by SPL, update the SPL symbols to use this instead of
offset, which might be incorrect if hierarchical sections are used.
Signed-off-by: Simon Glass <sjg@chromium.org>
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.
At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.
A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.
It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:
tegra
sunxi
x86
The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit 5e5745465c.
The reverted commit didn't support the scenario where there are less
DRAM banks in U-Boot than in Linux.
Also, it didn't introduce any new functionality, only limitaion.
User could just increase MEMORY_BANKS_MAX if it's too small.
Reviewed-by: Simon Glass <sjg@chromium.org>
In raw mode, handle ctrl-c as normal. This allows normal ctrl-c behavior
such as aborting a command that is timing out without completely
terminating the sandbox executable.
In [1], Simon disabled this. His reason for it was that it interferes
with piping test scripts. Piping should be done in cooked mode, so this
change should still not interfere.
[1] commit 8969ea3e9f ("sandbox: Disable Ctrl-C")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't necessarily want to re-enable ctrl-c if it was already disabled
when calling tstc().
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some legacy boards use RAW image for SPL boot. Add Kconfig option
SPL_PAYLOAD to set alternative image.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The second argument of fdt_fixup_mtdparts() is an opaque pointer,
'void *node_info', hence callers can pass any pointer.
Obviously, fdt_fixup_mtdparts() expects 'struct node_info *'
otherwise, it crashes run-time.
Change the prototype so that it is compile-time checked.
Also, add 'const' qualifier to it so that callers can constify
the struct node_info arrays.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Header file "asm/utils.h" is not required to compile "spl_ymodem.c".
So, removing this dependency allows other architectures to use this
booting device as "asm/utils.h" is only present in "arm" architecture.
Signed-off-by: Paulo Zaneti <paulo.zaneti@datacom.ind.br>
Use blk_dread()/blk_dwrite() in mmc_read()/mmc_write() AVB operation
implementations. This fixes compilation issues when CONFIG_BLK is
enabled.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Some boards indicate support from booting NAND or
ONENAND booting, but don't enable the CONFIG_NAND. This
makes those boards imply NAND which will make
enabling other flags that are dependent on CONFIG_NAND
possible and easier to migrate.
Signed-off-by: Adam Ford <aford173@gmail.com>
On some boards, we want to give the board/architecture-specific code a
chance to look at where the next image has been loaded from and
perform fixups before starting the next image. This is of particular
importance, when we probe multiple devices for bootable payloads and
boot the first one found.
This change adds the following:
- we record the boot_device used into the spl_image structure
- we provide an extension-point for boards/architectures that can
perform late fixups depending on a fully populated spl_image
structure (i.e. we'll know the final boot_device and have info
on the image type and operating system to be booted).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
A message should be displayed if an image is loaded
to an FPGA, because the hardware might have changed,
and the user should be informed
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the ram_base to store the start address of
the first bank DRAM and the use this ram_base to calculate ram_top
properly. This patch fixes the erroneous calculation of ram_top
incase of non zero ram start address.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Driver supports only one instance of usb keyboard.
Remove the first dependency on generic usbkbd DEVNAME.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
command_ret_t enum contains 3 return values but only two are handled
now. Extend cmd_process_error() and handle CMD_RET_USAGE separately.
These commands are affected by this change.
cmd/demo.c
cmd/efi.c
cmd/gpio.c
cmd/qfw.c
cmd/x86/fsp.c
test/dm/cmd_dm.c
And scripts shouldn't be affected because return value is not 0. But
every command implementation can choose what it is correct to pass.
I would expect that RET_USAGE is called when parameters are not
correctly passed (have incorrect value, missing parameters)
and RET_FAILURE when correct parameters are passed but command fails.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
In ARM 64-bits, memory size can be supported is more than 4GB,
hence increasing save array is needed to cope with testing larger memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Typically init_scsi() does not output anything. So initr_scsi() should
provide a \n or we may see borked output like
SCSI: Net: No ethernet found.
as observed with sandbox_defconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The hashed-strings signature property includes two uint32_t values.
The first is unneeded as there should never be a start offset into the
strings region. The second, the size, is needed because the added
signature node appends to this region.
See tools/image-host.c, where a static 0 value is used for the offset.
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new config value FIT_SIGNATURE_MAX_SIZE, which controls the
max size of a FIT header's totalsize field. The field is checked before
signature checks are applied to protect from reading past the intended
FIT regions.
This field is not part of the vboot signature so it should be sanity
checked. If the field is corrupted then the structure or string region
reads may have unintended behavior, such as reading from device memory.
A default value of 256MB is set and intended to support most max storage
sizes.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Verification of hashes needs to take place before any image post
processing, thus matching full FIT image processing.
This allows mechanisms such as encryption be applied to images
prior to fit generation at the spl level.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Move the FPGA loading from IS_ENABLED(CONFIG_SPL_OS_BOOT) &&
IS_ENABLED(CONFIG_SPL_GZIP) conditional. The FPGA loading can
be used without OS loading and GZIP support in SPL. This issue
was most likely induced by some merge conflict, so fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Handle the case where the full fitImage support is enabled. In this
case, the whole fitImage must be loaded up front as some parts of the
fitImage code require memory-mapped access to the entire fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Handle the case where the full fitImage support is enabled. In this
case, the whole fitImage must be loaded up front as some parts of the
fitImage code require memory-mapped access to the entire fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Rather than verifying configuration signature of the configuration node
containing the kernel image types, verify all configuration nodes, even
those that do not contain kernel images. This is useful when the nodes
contain ie. standalone OSes or U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET, so can use
CONFIG_IS_ENABLED(DM_RESET) checking in reset.h later.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With driver model philosophy, we should avoid explicitly calling
driver initialization routine during boot. This updates the ram
init sequence table to exclude the IDE initialization for DM BLK.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ARM64 has 2 MiB alignment requirement for the kernel. When using
fitImage, this requirement may by violated, the kernel will thus be
executed from unaligned address and fail to boot. Do what booti does
and run booti_setup() for kernel_noload images on arm64 to obtain a
suitable aligned address to which the image shall be relocated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Both putc() and puts() can be called before global_data is set up. Some of
the code paths don't handle this correctly. Add an explicit test before
any member is accessed.
Reported-by: Coverity (CID: 169030)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Don't continue updating the offset when buffer is full.
When the buffer size exhausts and there's no space left to write
warn the user and update only the needed size and not both the
offset and needed size.
Add needed buffer size information in the iotrace command.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The header definitions are needed for reading
record information in cmd/iotrace.c
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
1. Add initial support of boot states mode (red, green, yellow)
2. Add functions for enforcing dm-verity configurations
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Implement AVB ops on top of existing mmc subsystem API. Currently there
is a full implementation of such operations, defined by [1]
AVB2.0 specification:
.read_from_partition() - reads N bytes from a partition identified by
a name.
.write_to_partition() - Writes N bytes to a partition identified by a name.
.validate_vbmeta_public_key() - checks if the given public ‘vbmeta’
partition is trusted.
.get_unique_guid_for_partition() - Gets the GUID for a partition identified
by a string name.
As [1] specification recommends to use tamper-evident storage for storing
rollback indexes and device state (LOCKED/UNLOCKED),
currently are only stubs instead of full implementation for these ops:
.read_rollback_index() - Gets the rollback index for a given index location
.write_rollback_index() - Sets the rollback index to a given location
.read_is_device_unlocked() - Gets where the device is unlocked
[1] https://android.googlesource.com/platform/external/avb/+/master/README.md
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
