Enable access to ESM0 configuration space and add Main ESM0 and MCU ESM
nodes to the AM64 device tree.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Add functionality to enable, set priority to the input events and to
route to MCU ESM. On AM64x/AM62x devices, it is possible to route Main
ESM0 error events to MCU ESM. When these error events are routed to MCU
ESM high output, it can trigger the reset logic to reset the device,
when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is set to '0'.
K3 based J7 devices (ex: J721e) also have ESM modules, and the changes
to the driver does not impact those devices.
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- Rearrange defconfig option order
- Add CONFIG_SAVE_PREV_BL_* options
- Doc updates:
- remove wrong SBOOT memory corruption note, because
memory is changed during u-boot bringup process,
not by SBOOT
- put payload on ramdisk place in abl boot image
creation step
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
BSP boot0 executes resistor calibration before clocks are initialized.
Let's do that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H6 and H616 SPL code has a few writes to unknown PRCM registers. Now
that we know what they are, let's replace magic offsets with proper
register names.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fix non working console on uart2, that seems releated to both
Allwinner H2+ and H3.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
[Andre: remove H2+, rearrange pin setup order]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This syncs the sun8i-h3-nanopi-neo.dts from the Linux tree, from tag
v5.18-rc1.
The alias is required to enable automatic MAC address generation.
Signed-off-by: Baltazár Radics <baltazar.radics@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.
This also has the added benefit of picking the right clock/reset
bits for H6 and new SoCs that have a rearranged PRCM MMIO space.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Chips attached to the RSB bus require an initialization command before
they can be used. (Specifically, this command programs the chip's
runtime address.) The driver does this in its .probe_chip hook, under
the assumption that .probe_chip is called during child probe. This is
not the case; .probe_chip is only called by dm_i2c_probe, which is
intended for use by board-level code, not for chips with OF nodes.
Since this initialization command must be run before a child chip can be
used, do it before probing each child.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, clock/reset setup for this device is handled by a
platform-specific function and is intermixed with non-DM pinctrl
setup. Use the devicetree to get clocks/resets, which disentagles
it from the pinctrl setup in preparation for moving to DM_PINCTRL.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Chips attached to the P2WI bus require an initialization command before
they can be used. (Specifically, this switches the chip from I2C mode
to P2WI mode.) The driver does this in its .probe_chip hook, under the
assumption that .probe_chip is called during child probe. This is not
the case; .probe_chip is only called by dm_i2c_probe, which is intended
for use by board-level code, not for chips with OF nodes.
Since this initialization command must be run before a child chip can be
used, do it before probing each child.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that mkimage can generate TOC0 images, and the SPL can interpret
them, hook up the build infrastructure so the user can choose which
image type to build. Since the absolute load address is stored in the
TOC0 header, that information must be passed to mkimage.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
SPL uses the image header to detect the boot device and to find the
offset of the next U-Boot stage. Since this information is stored
differently in the eGON and TOC0 image headers, add code to find the
correct value based on the image type currently in use.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most Allwinner sunxi SoCs have separate boot ROMs in non-secure and
secure mode. The "non-secure" or "normal" boot ROM (NBROM) uses the
existing sunxi_egon image type. The secure boot ROM (SBROM) uses a
completely different image type, known as TOC0.
A TOC0 image is composed of a header and two or more items. One item
is the firmware binary. The others form a chain linking the firmware
signature to the root-of-trust public key (ROTPK), which has its hash
burned in the SoC's eFuses. Signatures are made using RSA-2048 + SHA256.
The pseudo-ASN.1 structure is manually assembled; this is done to work
around bugs/quirks in the boot ROM, which vary between SoCs. This TOC0
implementation has been verified to work with the A50, A64, H5, H6,
and H616 SBROMs, and it may work with other SoCs.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As mkimage -T sunxi_egon now gains support for -A parameter, specify the
architecture when generating SPL boot image for sunxi.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There's now a sun20i family in sunxi, which uses RISC-V CPU.
Add support for making eGON.BT0 image for RISC-V.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Refactor some functions in mkimage sunxi_egon type, in order to prepare
for adding support for more CPU architectures (e.g. RISC-V). In
addition, compatibility for operation w/o specified architecture is
kept, in this case the architecture is assumed as ARM.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sunxi_egon type used to take no -A argument (because we assume sunxi
targets are all ARM). However, as Allwinner D1 appears as the first
RISC-V sunxi target, we need to support -A; in addition, as external
projects rely on U-Boot mkimage to generate sunxi eGON.BT0 header, we
need to keep compatibility with command line without -A.
As the default value of arch in mkimage is not proper (IH_ARCH_PPC
instead of IH_ARCH_INVALID), to keep more compatibility, add an Aflag
field to image parameters to describe whether an architecture is
explicitly specified.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is the only possible mux setting for the A64's PWM peripheral.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.
Clean up the code in the process: remove #ifdefs and recognize that the
pin configuration is the same for all sun8i/sun50i SoCs, not just those
which select CONFIG_MACH_SUN8I.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Where multiple options were available, the one matching board.c and the
device trees was chosen.
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixup H5 I2C1 pinmux]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This includes UART0 and R_UART (s_uart) on all supported platforms, plus
the additional UART configurations from arch/arm/mach-sunxi/board.c.
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sunxi pinctrl hardware has bias and drive control. Add driver
support for configuring those options.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pinmux command uses this function to display pinmux status.
Since the driver cannot map pin numbers to a list of supported
functions, only functions which are common across all pins can be
reported by name.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Implement the operations to get pin and function names, and to set the
mux for a pin. The pin count and pin names are calculated as if each
bank has the maximum number of pins. Function names are simply the index
into a list of { function name, mux value } pairs.
We assume all pins associated with a function use the same mux value for
that function. This is generally true within a group of pins on a single
port, but generally false when some peripheral can be muxed to multiple
ports. For example, A64 UART3 uses mux 3 on port D, and mux 2 on port H.
But all of the port D pins use the same mux value, and so do all of the
port H pins. This applies even when the pins for some function are not
contiguous, and when the lower-numbered mux values are unused. A good
example of both of these cases is SPI0 on most SoCs.
This strategy saves a lot of space (which is especially important for
SPL), but where the mux value for a certain function differs across
ports, it forces us to choose a single port for that function at build
time. Since almost all boards use the default (i.e. reference design)
pin muxes[1], this is unlikely to be a problem.
[1]: See commit dda9fa734f ("sunxi: Simplify MMC pinmux selection")
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: add comment summarising the commit message]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Create a do-nothing driver for each sunxi pin controller variant.
Since only one driver can automatically bind to a DT node, since the
GPIO driver already requires a manual binding process, and since the
pinctrl driver needs access to some of the same information, refactor
the GPIO driver to be bound by the pinctrl driver. This commit should
cause no functional change.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
U-boot is intended to replace linux kernel in android boot image(ABL), and
it's FIT payload to replace initramfs file. The boot process is similar to
boot image with linux:
- android bootloader (ABL) unpacks android boot image
- ABL sets `linux,initrd-start property` in chosen node in unpacked FDT
- ABL sets x0 register to FDT address, and passes control to u-boot
- u-boot reads x0 register, and stores it in `prevbl_fdt_addr` env variable
- u-boot reads `linux,initrd-start` property,
and stores it in `prevbl_initrd_start_addr`
In this way, u-boot bootcmd relies on `prevbl_initrd_start_addr` env
variable, and boils down to `bootm $prevbl_initrd_start_addr`.
If more control on boot process is desired, pack a boot script in
FIT image, and put it to default configuration
What done:
- strip unneeded config options
- add FIT image support
- add framebuffer node, u-boot logo and video console
- increase LMB_MAX_REGIONS, to store all linux dtb reserved memory regions
- add linux kernel image header
Uart driver causes hang, when u-boot is used in android boot image instead
of linux. Temporary disable console driver, until investigated and fixed.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
When u-boot is used as a chain-loaded bootloader (replacing OS kernel),
previous bootloader leaves data in RAM, that can be reused.
For example, on recent arm linux system, when chainloading u-boot,
there are initramfs and fdt in RAM prepared for OS booting. Initramfs
may be modified to store u-boot's payload, thus providing the ability to
use chainloaded u-boot to boot OS without any storage support.
Two config options added:
- SAVE_PREV_BL_INITRAMFS_START_ADDR
saves initramfs start address to 'prevbl_initrd_start_addr' environment
variable
- SAVE_PREV_BL_FDT_ADDR
saves fdt address to 'prevbl_fdt_addr' environment variable
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
We already support the NVMe commands and PCIe backend in the QEMU target,
so let's make it easy for anyone to consume them and enable NVMe distro
boot along the way!
With this patch, I can put an NVMe backed disk image into my QEMU VM and
have it automatically load a UEFI target blob.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
/LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
yoje
=SwGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
If include/generated/env.in does not exist, which is a typical case for
clean build, quiet_cmd_gen_envp command tries to delete this file
unconditionally.
This produces following warning during the build:
ENVP include/generated/env.in
rm: cannot remove 'include/generated/env.in': No such file or directory
Add '-f' option to the `rm` command to not complain if file does not
exist.
Fixes: f432eb6d8a ("env: Avoid using a leftover text-environment file")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Unfortunately, we require additional logic to buildman to support this
removal and still use SYS_SOC, etc, for build targets.
This reverts commit eeec00072d.
Signed-off-by: Tom Rini <trini@konsulko.com>
This brings in two related series. The first from Andre:
This series is the continuation of last year's effort to support the new
Armv8-R64 application profile. This led to a significant rework of the
existing fastmodel (FVP) support, to both upgrade it to newest U-Boot
standards (OF_CONTROL and distro_boot support), but also to generalise
the code, so that plugging in the v8-R64 support in the last patch gets
much easier. This is because apart from the twisted memory map between
the two profiles there is actually little difference, when it comes to
U-Boot relevant parts of the hardware.
I kept the legacy semihosting support (which picks up magic files from
the current directory), but if that fails, we go and try virtio-blk
(.iso installer images work), then virtio-net.
Please have a look, and give it a try, if possible. Both the v8-R and
v8-A FVP models are available for free on the Arm website[1].
Patch 01/11 fixes a regression introduced in December, it should be
applied now. The rest of the patches are for the next merge window.
[1]
https://developer.arm.com/tools-and-software/simulation-models/fast-models
And the second from Sean (where we exclude 27, 28 and 29 for now):
This cleans up the semihosting code and adds the following new features:
- hostfs support (like sandbox)
- support for being used as a SPL boot device
- serial device support
- falling back to normal drivers if semihosting is disabled
The main device affected by these changes is vexpress64, so I'd
appreciate
if Andre (or anyone else) could try booting.
These changes are motivated by bringup for ls1046a. When forcing JTAG
boot, this device disables most communication peripherals, including
serial and ethernet devices. This appears to be fixed in later
generation devices, but we are stuck with it for now. Semihosting
provides an easy way to run a few console commands.
The patches in this series are organized as follows:
0-4: rST conversions and other documentation updates
5-9: Semihosting cleanups
10-14: Filesystem support (including SPL boot device)
15-16: Serial support
16: Documentation update
17: JTAG boot support for LS1046A
19-25: Semihosting fallback
26-29: DM puts support
The last two groups of patches are "bonus;" the first 17 patches stand
on their own. The last two groups could be broken out as separate
series, but I have kept them in this one to help with my sanity (and not
have to deal with too many outstanding series).
Patch 14 depends on [1] to apply cleanly. Patch 17 depends on [2] for
correctness. This series should be applied to u-boot/next (in
particular, the EROFS series must have been applied).
[1]
https://lore.kernel.org/u-boot/CACRpkdZ+9fmNjC_mvrbPa9-iuTQVd8UkJ7Zpe7cL0c5vZygsVw@mail.gmail.com/T/
[2]
https://lore.kernel.org/u-boot/20220222183840.1355337-2-sean.anderson@seco.com/
