Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of
address space; however, not all of this space is covered by a device. In
particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped
at the far end of the address space.
In zlib, there is a loop that references p[-1] if p is non-NULL. Under
some circumstances, this leads to the CPU speculatively loading from
0xfffffff8 if p is NULL. This leads to a machine check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
continuation to the remaining mpc83xx boards that suffer from the same problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently this is not creating any problem. But it will result
in compilation error when used as below.
printf("CFG_SDRAM_CFG2 - %08x\n", CFG_SDRAM_CFG2);
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
continuation of the theme based on git grep "^#define CFG_.*;$" include/
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
bootdelay set to -1 'permanently' disables autobooting, even if
bootcmd is specified. Change to a positive value to allow
autobooting when a bootcmd is set.
Reported-by: Coray Tate <Coray.Tate@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now. Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Change LCRR clock ratio from 2 to 4 to commodate VSC7385.
Correct TSEC1 vs TSEC2 assignment.
Define ETHADDR and ETH1ADDR always.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
this seems as a good compromise between human memory, typing,
and last but not least, to accommodate for current and future kernel bloat.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
These changes were identified by HighSmith Bill ,Mazzyar and Joseph for
DDR configuration in u-boot code. Some are related to performance, some
affect stability and some correct few basic errors in the current
configuration.
The changes have been tested and found to give better memory latency
figures on MPC8313eRDB.LMBench figures prove it.
The changes are:
- CS0_CONFIG[ AP_n_EN] is changed from 1 to 0
(this may improve performance for application with many read
or write to open pages).
- CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to
001 (activating all the CS when only one is used may cause
unwanted noise on the system)
- TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on
Tras=45ns)
- TIMING_CFG_1[REFREC] changed from 21 clks to 18clks.
- TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to
comply with the 3 ODT clk requirements)
- TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4.
- TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks.
- DDR_SDRAM_MODE[AL]changed from 0 to 1.
- DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks.
- DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510.
- DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500.
The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git
The last commit on this tree was 6775c68683
Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com>
Cc: Bill HighSmith <Bill.Highsmith@freescale.com>
Cc: Razzaz Mazyar <MRazzaz@freescale.com>
Cc: Josep P J <PJ.Joseph@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
clean up the cache config from configs.h of board
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
convert to using simpler mpc85xx style fdt update code; streamline by
eliminating macros OF_SOC, OF_CPU, etc. which allows us to rm
the old school FLAT_TREE code from 83xx (since the sbc8349 was just
converted over to using libfdt).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
currently-defined 83xx boards. This change guarantees that the environment
will be located on the first flash sector after the U-Boot image.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
add board_add_ram_info, to make memory diagnostic output more
consistent. u-boot banner output now looks like:
DRAM: 256 MB (DDR1, 64-bit, ECC on)
and for boards with SDRAM on the local bus, a line such as this is
added:
SDRAM: 64 MB (local bus)
also replaced some magic numbers with their equivalent define names.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The 85xx code now relies on CONFIG_HAS_ETH0 to determine whether
to update TSEC1's device-tree node, so we need to add it
to all the boards with TSECs. Do this for 83xx and 86xx, too,
since they will eventually do something similar.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The tsec_info structure and array has a "flags" field for each
ethernet controller. This field is the only reason there are
settings. Switch to defining TSECn_FLAGS for each controller
in the config header, and we can greatly simplify the array, and
also simplify the addition of future boards.
Signed-off-by: Andy Fleming <afleming@freescale.com>
this enables libfdt code by default for the
freescale mpc8313erdb, mpc832xemds, mpc8349emds,
mpc8349itx and gp boards.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h
used to be included but CONFIG_BOOTP_MASK was not defined.
Remove lingering references to CFG_CMD_* symbols.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
