OCOTP driver is currently selected via CONFIG_MXC_OCOTP option.
Remove the old OCOTP related options, as they are not used anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Whilst U-boot does not require this itself, Linux currently relies upon
it having been muxed and enabled by the bootloader. Thus in order to
preserve compatibility with current kernels before a fix is merged in
Linux we will enable the SERIRQ interrupt and mux it to its pin.
Without doing this current kernels will never receive serial port
interrupts and the end result is typically that userland appears to
hang.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
CONFIG_SYS_NS16550_CLK specifies the rate of the clock 16x the baud
rate. The SMSC FDC37M81x datasheet states that a divider of 1 results in
a UART at 115200 baud, thus the x16 clock rate is 115200 * 16.
Previously the divider was left at 0 which led to a rate of 38400 baud
regardless of CONFIG_BAUDRATE or the baudrate environment variable.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The baudrate passed to Linux in the environment was hardcoded at 38400.
Instead pass the correct baudrate from global data, allowing Linux to
correctly inherit the baudrate used by U-boot when console setup is not
explicitly specified.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.
T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: removed Makefile blank line at EOF,
fix conflicts with moving DDR driver]
Acked-by: York Sun <yorksun@freescale.com>
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
The DRAM base has been zero for Power SoCs. It could be non-zero
for ARM SoCs. Use a macro instead of hard-coding to zero.
Signed-off-by: York Sun <yorksun@freescale.com>
Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.
TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit c360ceac.
Signed-off-by: York Sun <yorksun@freescale.com>
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
The default partition table matches the .dts files for these boards in
Linux. This allows these partitions to be used by name with U-Boot's
"nand" command.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
The offset of register address within GPIO module is just
CONFIG_SYS_MPC85xx_GPIO_ADDR. So, fix it. The following platforms
are confirmed: MPC8572, P1023, P1020, P1022, P2020, P4080,
P5020, P5040, T4240, B4860.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
The use of 'bool' data types in globally used header files cases build
errors like this:
In file included from arch/blackfin/include/asm/blackfin.h:13:0,
from include/common.h:92,
from cmd_test.c:17:
arch/blackfin/include/asm/blackfin_local.h:54:1: error: unknown type name 'bool'
Use plain 'int' instead to avoid such kind of trouble.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Some board have multiple configurations.
For example, the board "m54455evb" has many configurations:
M54455EVB, M54455EVB_a66, M54455EVB_i66, M54455EVB_intel, ...
When we modify board-related files, we need to test
all configurations based on such a board.
In such a case, the new option -b is useful.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
All objects under api/ and examples/api/ directories are selected
by CONFIG_API.
So we can move CONFIG_API switch to the top Makefile.
In order to use CONFIG_API, the definition of SUBDIR_EXAMPLES-y
must be moved after "sinlude $(obj)include/autoconf.mk".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The directory tools/ is always built before common/.
So when envcrc tool is necessary in common/Makefile,
it already exists.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
All objects under api/ and examples/api/ directories are selected
by CONFIG_API.
So we can move CONFIG_API switch to the top Makefile.
In order to use CONFIG_API, the definition of SUBDIR_EXAMPLES-y
must be moved after "sinlude $(obj)include/autoconf.mk".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 69434e4c deleted spieval board support
but it missed to clean up include/configs/spieval.h file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
tools/updater needs board/MAI/AmigaOneG3SE board
for compiling.
But AmigaOneG3SE board was already deleted
by Commit 953b7e6.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Some GPIO connected LEDs have inverted polarity.
Introduce new config option: CONFIG_GPIO_LED_INVERTED_TABLE for the
specifying the inverted GPIO LEDs list and add support for this in the
gpio_led driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
Add a check for the gpio_request() function return value and do not try
to configure the GPIO if the gpio_request() call fails.
Also, print an error message indicating the gpio_request() has failed.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
The CONFIG_GPIO_LED symbol does not have any documentation in the README
file. Document the CONFIG_GPIO_LED symbol.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
In the case of not having CONFIG_CMD_HASH but having CONFIG_CMD_CRC32
enabled (and not CONFIG_CRC32_VERIFY), we end up in this part of the
code path on hash_command(). However, we will only have exactly 3 args
here, and 3 > 3 is false, and we will not try and store the hash at the
address given as arg #3. The next problem however is that we've been
moving argv around so the third value is now in argv[0] not argv[3].
Confirmed on AM335x Beaglebone White.
Signed-off-by: Tom Rini <trini@ti.com>
This chip is compatible with the existing driver, except that it uses
BAR2 instead of BAR1 for the I/O memory region. Using this patch I can
use the PCIe ethernet interface on the CompuLab Trimslice to boot from
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276477
Instead of directly calling the low-level invalidate_dcache_range() and
flush_cache() functions, provide thin wrappers that take into account
alignment requirements.
While at it, fix a case where the cache was flushed but should have been
invalidated, two cases where the buffer data was flushed instead of the
descriptor and a missing cache invalidation before reading the packet
data that the NIC just wrote to memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276474
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.
With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
(When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
