MPC8610HPCD board adds -O2 gcc option to PLATFORM_CPPFLAGS
causing overriding default -Os option. New gcc (ver. 4.2.2)
produces warnings while compiling net/net.c file with -O2
option. The patch is an attempt to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This problem shows up with parallel builds only; it results in
somewhat cryptic error messages like
$ JOBS=-j6 MAKEALL netstar
Configuring for netstar board...
arm-linux-ld: cannot find -lgeneric
make[1]: *** [eeprom.srec] Error 1
A few boards (like netstar and voiceblue) need some libraries for
building; however, the board Makefile does not contain any such
dependencies which may cause problems with parallel builds. Adding
such dependencies is difficult as we would also have to provide build
rules, which already exist in the respective library Makefiles.
To solve this, we make sure that all libraries get built before the
board code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch changes the Canyonlands/Glacier fixed DDR2 controller setup
used for NAND booting to match the values needed for the new 512MB
DIMM modules shipped with the productions boards:
Crucial: CT6464AC667.8FB
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem with DIMMs that have 8 banks. Now the
MCIF0_MBxCF register will be setup correctly for this setup too.
This was noticed with the 512MB DIMM on Canyonlands/Glacier.
Signed-off-by: Stefan Roese <sr@denx.de>
Newer gcc's might be configured to enable autovectorization by default.
If we happen to build with one of those compilers we will get SPE
instructions in random code.
-mno-spe disables the compiler for automatically generating SPE
instructions without our knowledge.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename init_addr and init_ext_addr to match the docs between
85xx and 86xx. Both now use 'init_addr' and 'init_ext_addr'.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* adjust __spin_table alignment to match ePAPR v0.94 spec
* loop over all cpus when determing who is up. This fixes an issue if
the "boot cpu" isn't core0. The "boot cpu" will already be in the
cpu_up_mask so there is no harm
* Added some protection in the code to ensure proper behavior. These
changes are explicitly needed but don't hurt:
- Added eieio to ensure the "hot word" of the table is written after
all other table updates have occurred.
- Added isync to ensure we don't prefetch loading of table entries
until we a released
These issues we raised by Dave Liu.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
LWMON5 DSPIC POST uses the watch-dog scratch register. So, make
the CFG_DSPIC_TEST_ADDR definition more readable.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Some boards (e.g. lwmon5) need rather a frequent watch-dog
kicking. Since the time it takes for the flush_cache() function
to complete its job depends on the size of data being flushed, one
may encounter watch-dog resets on such boards when, for example,
download big files over ethernet.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Since the current dflush() implementation is know to have some problems
(as seem on lwmon5 ECC init) this patch removes it completely and replaces
it by using clean_dcache_range().
Tested on Katmai with ECC DIMM.
Signed-off-by: Stefan Roese <sr@denx.de>
As it seems the "old" ECC initialization routine by using dflush() didn't
write all lines in the dcache back to memory on lwmon5. This could lead
to ECC error upon Linux booting. This patch changes the program_ecc()
routine to now use clean_dcache_range() instead of dflush().
clean_dcache_range() uses dcbst which is exactly what we want in this
case.
Since dflush() is known is cause problems, this routine will be
removed completely and replaced by clean_dcache_range() with an
additional patch.
Signed-off-by: Stefan Roese <sr@denx.de>
On ppc405EP and ppc405GP (at least) the ebc is directly attached to the plb
and not to the opb. This patch will try to fixup /plb/ebc if /plb/opb/ebc
doesn't exist.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Move non-inlied functions into specific drivers file
Set get_prom as weak
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Vlad Lungu <vlad@comsys.ro>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Currently the timeout waiting for an ARP reply is hard set to 5 seconds.
On i.MX31ADS due to a hardware "strangeness" up to four first IP packets
to the boards get lost, which typically are ARP replies. By configuring
the timeout to a lower value we significantly improve the first network
transfer time on this board. The timeout is specified in milliseconds,
later internally it is converted to deciseconds, because it has to be
converted to hardware ticks, and CFG_HZ ranges from 900 to 27000000 on
different boards.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Remove a redundant register definition, clean up some coding style
violations.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The specification for the lwmon5 board dsPIC POST got changed.
Also add defines for the temperatures and voltages.
Signed-off-by: Sascha Laue <sascha.laue@liebherr.com>
If the hardware watchdog detects a voltage error, the watchdog sets
GPIO62 to low. The watchdog POST has to detect this low level.
Signed-off-by: Sascha Laue <leglas0@legpc180.leg.liebherr.i>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The IDE driver can use 32-bit addresses in LBA mode, in which case it
spits multiple warnings during compilation. Fix them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
out_8 wants a pointer to an unsigned as the first argument. Add a
maintainer for Linkstation boards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Arithmetic expressions do not get evaluated under stringification. Remove
default network configuration, add DHCP command support. Thanks to Felix
Radensky for reporting.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Since we didn't want to remove features from the configuration, we
decided to increase the U-Boot image size (add one flash sector).
Also changed the default environment definition to make it
independent of such changes.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Since we didn't want to remove features from the configuration, we
decided to increase the U-Boot image size (add one flash sector).
Also changed the default environment definition to make it
independent of such changes.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
