Some OSes require that secondary cores not be initialized when they
are booted (eg VxWorks). By default when U-Boot is compiled with the
CONFIG_MP option all secondary cores are brought out of reset and held
in spinloops. Setting the "mp_holdoff" environment variable to 'yes'
or '1' will cause U-Boot to leave secondary cores in their default
state.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When DDR controller interleaving is eabled and less than all bank (chip-select)
interleaving is seletected, the unused chip-select should be disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The memory test is performed after DDR initialization when U-boot stills runs
in flash and cache. On recent mpc85xx platforms, the total memory can be more
than 2GB. To cover whole memory, it needs be mapped 2GB at a time using a
sliding TLB window. After the testing, DDR is remapped with up to 2GB memory
from the lowest address as normal.
If memory test fails, DDR DIMM SPD and DDR controller registers are dumped for
further debugging.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A worker function setup_ddr_tlbs_phys() is introduced to implement more
control on physical address mapping.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The fixup routine must not fixup NULL pointers.
Problem can be seen by
char *testfun(void) __attribute__((weak));
char *(*myfun)(void) = testfun;
Then add
printf("myfun:%p, &myfun:%p\n", myfun, &myfun);
before relocation and after relocation.
myfun should be NULL in both cases but it is not.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.
Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
pumping line-rate traffic though a p4080 rev.2, which
is configured to encrypt packets prior to forwarding through
an IPsec tunnel, gets this error:
of_platform ffe302000.jq: DECO: desc idx 22: LIODN error. DECO was trying
to share from itself or from another DECO but the two Non-SEQ LIODN
values didn't match or the "shared from" DECO's Descriptor required that
the SEQ LIODNs be the same and they aren't.
Since high traffic rates cause DECOs to begin to start sharing
shared descriptors amongst themselves, and DECOs inherit job queue
LIODNs when accessing shared descriptors, and a recently discovered
rev.2 h/w erratum requires all sharing job queues in a partition
have same liodn assignment, reassign the first job queue's liodn
assignment to the rest.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
APM821XX is a new line of SoCs which are derivatives of
PPC44X family of processors. This patch adds support of CPU, cache,
tlb, 32k ocm, bootstraps, PLB and AHB bus.
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 800eb0964 "POST cleanup." removed file
arch/powerpc/cpu/mpc512x/common.c but failed to remove the reference
to it from arch/powerpc/cpu/mpc512x/Makefile which causes somewhat
obscure build errors:
make[1]: *** No rule to make target `/work/wd/tmp-ppc/arch/powerpc/cpu/mpc512x/.depend', needed by `_depend'. Stop.
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Move common code to the fsl_diu_fb.c file and remove obsolete
code from board files (aria, mpc8610hpcd and pdm360ng).
Move fsl_diu_fb.h file to the include directory.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This change lays the groundwork for the BOOTFLAG_* flags being removed.
This change has the small affect of delaying 100ms on PCI initialization
after a warm boot as opposed to the optimal 1ms on some boards.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
included the mpc8308_p1m board.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Configuring for MPC8308RDB board...
pcie.c: In function 'mpc83xx_pcie_register_hose':
pcie.c:143: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for setting PCIE clocks in cpu_init.c by
providing CONFIG_SYS_SCCR_PCIEXP{1,2} in configuration.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8308 has only one PCIE host controller so we want it to compile
without CONFIG_SYS_PCIE2_CFG_{BASE,SIZE} defined.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
By default the trace broadcast is enabled on 44x systems.
To reduce power consumption when instruction tracing is
not needed, disable trace broadcast.
Check External Debug Mode (EDM) bit to detect if it should be
disabled or not.
Resetting system via a debugger will set the DBCR0[EDM] bit.
Resetting via u-boot or OS will not.
Signed-off-by: Victor Gallardo <vgallardo@apm.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch cleans the PVR detection code in check_cpu() up a bit.
Basically the strings are better seperated, resulting in an easier
to understand and maintain code version.
The #ifdef's couldn't be removed easily because of two reasons:
- Some SoC revisions have the same PVR, so need a way to differentiate
between those two SoC's.
- In some case statements registers only available in this SoC variant
are referenced.
Instead I moved the CONFIG_440 #ifdef a bit, so that 405 platforms don't
add this 440 detection code and vice versa. Resulting in this U-Boot
image size change:
405EX (Kilauea): 408 bytes less
440EPx (Sequoia): 604 bytes less
460EX (Canyonlands): 564 bytes less
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
This patch removes the PPC4xx UART driver. Instead the common NS16550
driver is used, since all PPC4xx SoC's use this peripheral device.
The file 4xx_uart.c now only implements the UART clock calculation
function which also sets the SoC internal UART divisors.
All PPC4xx board config headers are changed to use this common NS16550
driver now.
Tested on these boards:
acadia, canyonlands, katmai, kilauea, sequoia, zeus
Signed-off-by: Stefan Roese <sr@denx.de>
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
As a part from this cleanup, the GPIO definitions for PPC405EP are
corrected. The high and low parts of the registers (for example
CONFIG_SYS_GPIO0_OSRL vs. CONFIG_SYS_GPIO0_OSRH) have been defined in
the wrong order. This patch now fixes this issue by switching these
xxxH and xxxL values. This brings the GPIO 405EP port in sync with all
other PPC4xx ports.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch starts a bit PPC4xx header cleanup. First patch mostly
touches PPC440 files. A later patch will touch the PPC405 files as well.
This cleanup is done by creating header files for all SoC versions and
moving the SoC specific defines into these special headers. This way the
common header ppc405.h and ppc440.h can be cleaned up finally.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the behaviour of the fdt_fixup_nor_flash_node()
function. Now it doesn't patch the size of the "reg" property with the
chip-select size, but with the size returned from the new function
flash_get_bank_size(). This function will return per weak default the
flash size of the bank (bank = chip-select numer) detected by the flash
driver. If this does not fit your needs, this function may be overridden
by a board specific one.
For this the parameters needed to be changed. So I intentionally squashed
the PPC4xx stuff using this routine into this patch. Otherwise it would
not be git-bisectable anymore.
The board specific function for the AMCC/APM Ebony eval board is now
included in this patch version.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Detlev Zundel <dzu@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Cc: Wolfgang Denk <wd@denx.de>
The Freescale MPC8610 and MPC5121 DIU code had re-implement two features that already
existed in U-Boot: bitmap drawing and top-of-screen logo (CONFIG_VIDEO_LOGO).
So delete the 8610-specific code and use the built-in features instead.
Signed-off-by: Timur Tabi <timur@freescale.com>
- Revives POST for blackfin arch;
- Removes redundant code:
arch/blackfin/lib/post.c
arch/powerpc/cpu/ppc4xx/commproc.c
arch/powerpc/cpu/mpc512x/common.c
- fixes up the post_word_{load|store} usage.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
List of the maintainers of the affected by patch boards:
Cc: Stephan Linz <linz@li-pro.net>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Cc: Larry Johnson <lrj@acm.org>
Cc: Feng Kan <fkan@amcc.com>
commit 47e26b1b "cmd_usage(): simplify return code handling" caused
the following compile warnings:
bedbug_860.c: In function 'bedbug860_do_break':
bedbug_860.c:73: warning: 'return' with a value, in function returning void
bedbug_860.c:121: warning: 'return' with a value, in function returning void
Fix the return type.
Actually these files could need some cleanup - commands should
return proper error codes, and there are coding style issues.
=> To be fixed later.
Signed-off-by: Wolfgang Denk <wd@denx.de>
We need to invalidate the data cache after it has been used as init-ram.
This problem was detected on the lwmon5 update.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a bug in reconfigure_pll(), where the detection of
the current bootstrap option is wrong. The ICS bits where incorrectly
shifted. This bug was found on the lwmon5 board, which uses bootstrap
option H (I2C bootstrap EEPROM).
Additionally a bit of code was moved into the if statement, since its
only used after later on. No need to run this code all the time.
Also, a few empty lines are added to make the code better readable.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rupjyoti Sarmah <rsarmah@amcc.com>
Cc: Victor Gallardo <vgallardo@appliedmicro.com>
We currently do not add a cpu-release-addr for core 0, this is needed
when we want to reset core 0 and later restart it from Linux
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Official docs call it the Job Ring not Job Queue for the p4080 security
block. Match the docs to reduce confusion.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fixes breakeage introduced by commit
a37c36f4e7 "powerpc/8xxx: query
feature reporting register for num cores on unknown cpus"
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver name does not need to be writable, so constify it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function. This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).
Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.
To avoid confusion, rename into getenv_f() [as "running from flash"]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
doing so helps avant garde users, such as those using simulators that
allow users to configure the number of cores, so as to not have to
manually adjust u-boot sources. h/w should also be reliably setting
FRR NCPU in the future.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enabled registered DIMMs using data from SPD. RDIMMs have registers
which need to be configured before using. The register configuration
words are stored in SPD byte 60~116 (JEDEC standard No.21-C). Software
should read those RCWs and put into DDR controller before initialization.
Signed-off-by: York Sun <yorksun@freescale.com>
Previous code presumes each DIMM has up to two rank (chip select). Newer
DDR controller supports up to four chip select on one DIMM.
Signed-off-by: York Sun <yorksun@freescale.com>
Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual
rank with 512MB each rank.
Also check dimm size and rank size for memory controller interleaving
Signed-off-by: York Sun <yorksun@freescale.com>
Replace environmental variables memctl_intlv_ctl and ba_intlv_ctl with
hwconfig parameters. The syntax is
setenv hwconfig "fsl_ddr:ctlr_intlv=<mode>,bank_intlv=<mode>"
The mode values for memory controller interleaving are
cacheline
page
bank
superbank
The mode values for bank interleaving are
cs0_cs1
cs2_cs3
cs0_cs1_and_cs2_cs3
cs0_cs1_cs2_cs3
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for initializing the SERDES blocks on CoreNet style QoriQ
devices and the p4080 specific SERDES tables to know which actual
componetns are enabled.
Additionally, split out the Frame Manger (FMAN) into its specific ethernet
ports instead of gross level of the full FMAN.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the new QorIQ/CoreNet based platforms we need to initialize the
"portals" as access into the Data Path subystem as well as Logical IO
Device Numbers (LIODN) that are used for the IOMMU (PAMU).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CoreNet style platforms can have a L3 cache that fronts the memory
controllers. Enable that cache as well as add information into the
device tree about it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If 36-bit physical address is used, move the INIT_RAM_ADDR to higher
address. This frees the low 4GB address space for better use.
Signed-off-by: York Sun <yorksun@freescale.com>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds the "ecctest" command to test and simulate ECC errors
(single bit and/or double bit) while running from SDRAM. Currently only
the IBM DDR2 controller is supported (405EX, 440SP(e), 460EX/GT).
This is done by copying and calling functions, modifying the SDRAM
controller operation mode, in internal SRAM/OCM.
For correctable ECC errors (single bit) only the status will be printed
since the DDR2 controller doesn't provide the faulting address:
=> ecctest 1000000 1
Using address 01000000 for 1 bit ECC error injection
ECC: Correctable error
Uncorrectable ECC errors (double bit) will also display the faulting
address:
=> ecctest 1000000 2
Using address 01000000 for 2 bit ECC error injection
ECC: Uncorrectable error at 0x0001000000
To enable this "ecctest" function you need to define CONFIG_CMD_ECCTEST
in the board config header.
Tested on katmai and t3corp.
Signed-off-by: Stefan Roese <sr@denx.de>
Use the correct macro instead of the hardcoded 0x4c to clear the ECC
status in the 440/460 DDR(2) error status register after ECC
initialization.
Also the non-440 parts (405EX(r) right now) and the IBM DDR PPC variants
(440GX) use a different registers to clear this error status. Use the
correct ones.
Signed-off-by: Stefan Roese <sr@denx.de>
Using this define, a board can define an opimized RFDC value and use
the auto calibration code to "tune" the remaining DDR2 controller
calibration register.
Signed-off-by: Stefan Roese <sr@denx.de>
Move serdes init until after we are in ram so we can keep track of a
global static protocal map for the particular serdes config we are in.
This makes is_serdes_configured() much simplier and not constantly
reading registers to determine if a given device is enabled based on the
protocol.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move serdes init until after we are in ram so we can keep track of a
global static protocal map for the particular serdes config we are in.
This makes is_serdes_configured() much simplier and not constantly
reading registers to determine if a given device is enabled based on the
protocol.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user manual refers to FMAN1 and FMAN2 not 0 and 1.
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On QorIQ CoreNet based devices we have a global clocking block. We want
to keep track of SYSCLK frequency as it is what is used to derive all
other frequencies in the SoC
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using fdt_node_offset_by_compat_reg to find the node offsets we
want to update instead of using aliases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The board maintainer states:
The GTH board is obsolete and has not been manufactured for
several years.
To my knowledge, no recent U-Boot build has been tested on that
card.
So drop support for this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Acked-by: Thomas Lange<thomas@corelatus.se>
The code to map SERDES configs to slot names is board specific and not
chip specific. Thus it should live in board/freescale/p1022ds/ and not
in arch/powerpc/cpu/.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 'errata' command to report what errata we workaround. Report
workaround for erratum SATA-A001 on P1022/P1013.
Also sorted the CONFIG_CMD_* list.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifics:
1) 36-bit only
2) Booting from NOR flash only
3) Environment stored in NOR flash only
4) No SPI support
5) No DIU support
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Each platform had its own version of the upmconfig, despite the
init process being identical. Now that we have a spot for common
lbc code, create a common upmconfig() there.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new command dumps the TLBCAM, the LAWs, and the BR/OR regs.
Add CONFIG_CMD_REGINFO to the config for all MPC85xx parts.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This dumps out the contents of TLB1 on 85xx-based systems.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extract the operation to read a tlb into a function - we will need
this later to print out the tlbs, and there's no point in duplicating
the code. Create a TSIZE_TO_BYTES macro to deal with the conversion
from the MAS field to an actual size instead of duplicating this in code.
There are a few misc other minor cleanups.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We may have cpu-handles pointing to the cpu nodes we delete. If so we
should delete the handles as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_FSL_SEC_COMPAT is set to 2 for the SEC 2.x and SEC 3.x.
Parts with newer SEC h/w versions will increment the number to
accomodate incompatible code changes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds basic support for Freescale MPC8308 CPU. Serial ports,
NOR flash and integrated Ethernet controllers are supported.
PCI Express is also supported. eSDHC, NAND and USB may work but aren't
tested (using ULPI PHY requires additional patch).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Background Info:
Some PPC440/460 boards have caches enabled in the Boot/FLASH TLB (via
init.S) to speed up the boot process. In relocate_code (start.S) the
cache inhibit attribute for this TLB is set to disable cache. This is
needed for the CFI FLASH driver.
This patch now cleans this code up:
- CONFIG_SYS_TLB_FOR_BOOT_FLASH is defined to 0 (default TLB) if not
defined in the top of this file. This way, we can remove an ugly
#ifdef in this code.
- Replace complex "#if defined(CONFIG_440EP) || defined(CONFIG_GR)..."
statement with "#if defined(CONFIG_440)".
- Remove unnecessary cache invalidate calls resulting in faster bootup.
Signed-off-by: Stefan Roese <sr@denx.de>
As described in item #10 of the SDRAM initialization (chapter 22.2.9
of the PPC460EX/EXr/GT users manual), RDSS may need to be adjusted. The
code for this is now factored out and executed for non-SPD based boards
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch makes it possible to overwrite the default auto-calibration
scan window (SDRAM_WRDTR.[WDTR], SDRAM_CLKTR.[CKTR] values) with
board specific values. The parameters of the weak default function are
corrected as well. This way we don't need the casts any more.
This feature will be used by an upcoming PPC460GT board port.
Signed-off-by: Stefan Roese <sr@denx.de>
By not defining CONFIG_SYS_PCI_MASTER_INIT and CONFIG_SYS_PCI_TARGET_INIT,
PCI support (host and adapter) will not be enabled. But it's still
possible to use the U-Boot PCI infrastructure for the PCIe ports.
This configuration option is needed for a new 460GT board, which uses
PCIe but has PCI disabled.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables booting with option E on the PPC460EX/EXr/GT.
When booting with Option E, the PLL is in bypass, CPR0_PLLC[ENG]=0.
The Software Boot Configuration Procedure is needed to engage the
PLL and perform a chip reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 460c2ce3 "MPC5200: workaround data corruption for unaligned
local bus accesses" fixed the problem for MPC5200 only, but MPC512x is
affected as well, so apply the same fix here, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
The MPC5200 has a nasty problem that will cause silent data corruption
when performing unaligned 16 or 32 byte accesses when reading from the
local bus - typically this affects reading from flash. The problem can
be easily shown:
=> md fc0c0000 10
fc0c0000: 323e4337 01626f6f 74636d64 3d72756e 2>C7.bootcmd=run
fc0c0010: 206e6574 5f6e6673 00626f6f 7464656c net_nfs.bootdel
fc0c0020: 61793d35 00626175 64726174 653d3131 ay=5.baudrate=11
fc0c0030: 35323030 00707265 626f6f74 3d656368 5200.preboot=ech
=> md fc0c0001 10
fc0c0001: 65636801 00000074 0000003d 00000020 ech....t...=...
fc0c0011: 0000005f 00000000 00000074 00000061 ..._.......t...a
fc0c0021: 00000000 00000064 00000065 00000035 .......d...e...5
fc0c0031: 00000000 00000062 0000003d 0000006f .......b...=...o
=> md.w fc0c0001 10
fc0c0001: 0000 3701 0000 6f74 0000 643d 0000 6e20 ..7...ot..d=..n
fc0c0011: 0000 745f 0000 7300 0000 6f74 0000 6c61 ..t_..s...ot..la
This commit implements a workaround at least for the most blatant
problem: using memcpy() from NOR flash. We rename the assembler
routine into __memcpy() and provide a wrapper, which will use a
byte-wise copy loop for unaligned source or target addresses when
reading from NOR flash, and branch to the optimized __memcpy()
in all other cases, thus minimizing the performance impact.
Tested on lite5200b and TQM5200S.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Do not enforce drivers to provide empty video_set_lut()
if they do not implement indexed color (8 bpp) frame
buffer support. Add default function to the cfb_console
driver and remove empty video_set_lut() functions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
