Adding timer init function in timer-uclass driver to create and
initialize the timer device on platforms where u-boot,dm-pre-reloc
is not used. Since there will be multiple timer devices in the
system, adding a tick-timer node in chosen node to know which
timer device to be used as tick timer in u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
This patch adds code which sets up 2-level page tables on ARM64 thus
extending available VA space. CPUs implementing 64k translation
granule are able to use direct PA-VA mapping of the whole 48 bit
address space.
It also adds the ability to reset the SCTRL register at the very beginning
of execution to avoid interference from stale mappings set up by early
firmware/loaders/etc.
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Document the usage of 'qfw' command
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c
writes/reads the tail of each NOR flash bank to check if the device
really resides there.
If CS1_SPLIT were enabled, the support card would always require two
NOR flash devices to be inserted for the correct NOR detection.
This is not probably what we want.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Various updates did not make it through to this board. Also the instructions
for building a SPI image are no-longer correct. Fix these so that Jerry can
boot to a prompt again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check for bmode before reading the boot device
to check if a serial downloader is started,
and returns UART if the serial downloader is set,
letting SPL to wait for an image if
CONFIG_SPL_YMODEM_SUPPORT is set.
This allows to load again a SPL based board
with imx_usb_loader together with a tool
such as kermit.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Tested-by: Eric Nelson <eric@nelint.com>
These boards are similar enough to be supported in a single defconfig
file. Distinguish one from another by "DEVICE_TREE" from the command
line. The how-to-build in doc/README.uniphier should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These two are similar enough to be merged into a single
defconfig file. Distinguish one from another by "DEVICE_TREE"
from the command line. The how-to-build in doc/README.uniphier
should be also updated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since both altera_jtag_uart and altera_uart are converted to driver
model, remove them from the list of drivers remaining to convert.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Chin Liang See <clsee@altera.com>
We now using imagename to select rockchip's spl hdr & spl size.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
show how to packet rk3036 uboot image and boot from SD
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Series-to: u-boot
Series-version: 8
Series-cc: Lin Huang <hl@rock-chips.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
The optional parameter bootable is added in gpt command to set the
partition attribute flag "Legacy BIOS bootable"
This flag is used in extlinux and so in with distro to select
the boot partition where is located the configuration file
(please check out doc/README.distro for details).
With this parameter, U-Boot can be used to create the boot partition
needed for device using distro.
example of use:
setenv partitions "name=u-boot,size=60MiB;name=boot,size=60Mib,bootable;\
name=rootfs,size=0"
> gpt write mmc 0 $partitions
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x0001e021 "u-boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: cceb0b18-39cb-d547-9db7-03b405fa77d4
2 0x0001e022 0x0003c021 "boot"
attrs: 0x0000000000000004
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: d4981a2b-0478-544e-9607-7fd3c651068d
3 0x0003c022 0x003a9fde "rootfs"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
guid: 6d6c9a36-e919-264d-a9ee-bd00379686c7
> part list mmc 0 -bootable devplist
> printenv devplist
devplist=2
Then the distro scripts will search extlinux in partition 2
and not in the first partition.
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
./doc/README.gpt entry has been updated to explain usage of "gpt verify"
command.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a README with a brief guide to porting serial drivers over to use
driver model.
Add a timeline also. All serial drivers should be converted by the end
of January 2016.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for loading splash image from an SD card formatted with
a filesystem. Update boards to maintain original behavior where needed.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
short strings can be used in type parameter of gpt command
to replace the guid string for the types known by u-boot
partitions = name=boot,size=0x6bc00,type=data; \
name=root,size=0x7538ba00,type=linux;
gpt write mmc 0 $partitions
and they are also used to display the type of partition
in "part list" command
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x0000037f "boot"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: d117f98e-6f2c-d04b-a5b2-331a19f91cb2
2 0x00000380 0x003a9fdc "root"
attrs: 0x0000000000000000
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 25718777-d0ad-7443-9e60-02cb591c9737
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
code under flag CONFIG_PARTITION_TYPE_GUID
add parameter "type" to select partition type guid
example of use with gpt command :
partitions = uuid_disk=${uuid_gpt_disk}; \
name=boot,size=0x6bc00,uuid=${uuid_gpt_boot}; \
name=root,size=0x7538ba00,uuid=${uuid_gpt_root}, \
type=0fc63daf-8483-4772-8e79-3d69d8477de4;
gpt write mmc 0 $partitions
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Previously, Linux used the same GUID for the data partitions as Windows
(Basic data partition: EBD0A0A2-B9E5-4433-87C0-68B6B72699C7).
This created problems when dual-booting Linux and Windows in UEFI-GPT
Setup, so a new GUID (Linux filesystem data:
0FC63DAF-8483-4772-8E79-3D69D8477DE4) was defined jointly by GPT fdisk
and GNU Parted developers.
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
The 10m50 devboard becomes the new golden reference design of
Nios II Linux. So change README.nios2 to use 10m50 as template.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Add Altera Generic Quad SPI Controller support. The controller
converts SPI NOR flash to parallel flash interface. So it is
not like other SPI flash, but rather like CFI flash.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This commit adds:
- new uclass id: UCLASS_ADC
- new uclass driver: drivers/adc/adc-uclass.c
The new uclass's API allows for ADC operation on:
* single-channel with channel selection by a number
* multti-channel with channel selection by bit mask
ADC uclass's functions:
* single-channel:
- adc_start_channel() - start channel conversion
- adc_channel_data() - get conversion data
- adc_channel_single_shot() - start/get conversion data
* multi-channel:
- adc_start_channels() - start selected channels conversion
- adc_channels_data() - get conversion data
- adc_channels_single_shot() - start/get conversion data for channels
selected by bit mask
* general:
- adc_stop() - stop the conversion
- adc_vdd_value() - positive reference Voltage value with polarity [uV]
- adc_vss_value() - negative reference Voltage value with polarity [uV]
- adc_data_mask() - conversion data bit mask
The device tree can provide below constraints/properties:
- vdd-polarity-negative: if true: Vdd = vdd-microvolts * (-1)
- vss-polarity-negative: if true: Vss = vss-microvolts * (-1)
- vdd-supply: phandle to Vdd regulator's node
- vss-supply: phandle to Vss regulator's node
And optional, checked only if the above corresponding, doesn't exist:
- vdd-microvolts: positive reference Voltage [uV]
- vss-microvolts: negative reference Voltage [uV]
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This driver allows I/O operations on the Samsung S2MPS11 PMIC,
which provides lots of LDO/BUCK outputs.
To enable it, update defconfig with:
- CONFIG_PMIC_S2MPS11
and additional, if were not defined:
- CONFIG_CMD_PMIC
- CONFIG_ERRNO_STR
The binding info: doc/device-tree-bindings/pmic/s2mps11.txt
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CPU name for Exynos was concatenated with cpu id,
but for new Exynos platforms, like Chromebook Peach Pi
based on Exynos5800, the name of SoC variant does not
include the real SoC cpu id (0x5422).
For such case, the CPU name should be defined in device tree.
This commit introduces new device-tree property for Exynos:
- "cpu-model" - with cpu name string
If defined, then the cpu id is not printed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For most PPC platforms, they will call the first get_clocks() in
init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is
then defined to call the second get_clocks(), which should be
redundant for PPC.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: John Otken <jotken@softadvances.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added device-tree-binding information for zynq qspi controller
driver.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Export fdt_blob to the environment variable. So that we may
use it to boot Linux.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera sysid to driver model with misc uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert nios2 cpu to driver model. The cpu parameters are
extracted from device tree and saved to global data structure.
We will use them to replace the custom_fpga.h .
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_pio to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Convert altera_jtag_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many System on Chip(SoC) solutions are complex with multiple processors
on the same die dedicated to either general purpose of specialized
functions. Many examples do exist in today's SoCs from various vendors.
Typical examples are micro controllers such as an ARM M3/M0 doing a
offload of specific function such as event integration or power
management or controlling camera etc.
Traditionally, the responsibility of loading up such a processor with a
firmware and communication has been with a High Level Operating
System(HLOS) such as Linux. However, there exists classes of products
where Linux would need to expect services from such a processor or the
delay of Linux and operating system being able to load up such a
firmware is unacceptable.
To address these needs, we need some minimal capability to load such a
system and ensure it is started prior to an Operating System(Linux or
any other) is started up.
NOTE: This is NOT meant to be a solve-all solution, instead, it tries to
address certain class of SoCs and products that need such a solution.
A very simple model is introduced here as part of the initial support
that supports microcontrollers with internal memory (no MMU, no
execution from external memory, or specific image format needs). This
basic framework can then (hopefully) be extensible to other complex SoC
processor support as need be.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have added MRC cache for Intel FSP and BayTrail codes,
enable it for all BayTrail boards (Bayley Bay and Minnow Max).
Note it turns out that FSP for Intel Atom E6xx does not produce
the HOB for NV storage, so we don't have such functionality on
Intel Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce a new fsp command and make the existing hob command a
sub-command to fsp for future extension. Also move cmd_hob.c to
the dedicated fsp sub-directory in arch/x86/lib.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
System Management BIOS (SMBIOS) is a specification for how
motherboard and system vendors present management information
about their products in a standard format by extending the BIOS
interface on Intel architecture systems. As of today the latest
spec is 3.0 and can be downloaded from DMTF website. This commit
adds a simple and minimum required implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Current document about how to boot VxWorks is limited.
Add several chapters in README.vxworks to document this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 8fe11b8901.
I'll add support to lwmon5 in the next patch and will remove
support for the broken lcd4_lwmon5 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Desktop Management Interface (DMI) is not supported by U-Boot now.
Add it to the TODO list.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Document porting considerations for Intel Quark based board,
including MRC parameters and PCIe initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This board has not been converted to generic board by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
CONFIG_X86_OPTION_ROM_ADDR has been renamed to CONFIG_VGA_BIOS_ADDR.
Update the doc to refer to the new name.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Documentation file for DFU extension. With this functionality it is now
possible to transfer FIT images with firmware updates via TFTP and use
DFU backend for storing them.
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It is easier to paste these into the command line if they are a single
common. Use line continuation instead of separate lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
MMC support works now, so it can be dropped from the todo
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of creating a rockchip SPL SD card image with 32KB of zeros
which can be written to the start of an SD card, create the images with
only the useful data that should be written to an offset of 32KB on the
SD card.
The first 32 kilobytes aren't needed for bootup and only serve as
convenient way of accidentally obliterating your partition table.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The Radxa Rock pro board is rk3188 based and thus won't work with U-Boot
built for RK3288. Change the documentation to refer to the intended
board, the Radxa Rock 2, which is an RK3288-based design very similar to
the firefly
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files from Linux. Since mainline Linux is
somewhat behind, use the files from the Chromium tree. We can re-sync once
further code is acccepted upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Dan Malek <dan@embeddedalley.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Remove CONFIG_LWMON5 references.
(Also, remove undefined CONFIG_WD_MAX_RATE while I am here.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>
