The total FIFO size of some SoCs may be different from the existen, this
patch supports fifo size setting from platform data.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far, Rockchip SoCs have two kinds of USB2.0 phy, such as Synopsys and
Innosilicon. This patch applys dwc2 usb driver framework to implement
phy_init() and phy_off() methods for Synopsys phy on Rockchip platform.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
It conflicts with the generic_timer.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for rockchip rk33 series Soc like rk3368 and rk3399
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
In preparation for RK3368 and RK3399, which need to select ARM64, don't
select CPU_V7 at the ARCH_ROCKCHIP level but at the SoC level instead.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Simon Glass <sjg@chromium.org>
The 'evb_rk3036' and 'kylin' is not a vendor name, let's replace them
to 'rockchip' which is a real _vendor_ name, and meet the architecure
'board/<vendor>/<board-name>/'.
More boards from rockchip like evb_rk3288, evb_rk3399 will comes later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.kernel@gmail.com>
evb-3288 board RK3288-based development board with 2 USB ports, HDMI,
VGA, micro-SD card, audio, WiFi and Gigabit Ethernet. It also includes
on-board 8G eMMC and 2GB of SDRAM. Expansion connector provide access to
display pins, I2C, SPI, UART and GPIOs. This add some basic files
required to allow the board to output serial messaged and can run
command(mmc info etc).
evb-rk3288 also supports booting from eMMC or SD card, the default is eMMC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we would like to boot from SD card, we have to implement mmc driver
in SPL stage, and get a slightly large SPL binary. Rockchip SoC's
bootrom code has the ability to load spl and u-boot, then boot.
If CONFIG_ROCKCHIP_SPL_BACK_TO_BROM is enabled, the spl will return to
bootrom in board_init_f(), then bootrom loads u-boot binary.
Loading sequence after rework:
bootrom ==> spl ==> bootrom ==> u-boot
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed up spelling of U-Boot, boorom, opinion->option, Rochchip:
Signed-off-by: Simon Glass <sjg@chromium.org>
Most users of CONFIG_I2C_EEPROM were migrated to defconfig a while ago,
but sandbox was skipped. Leave it off for sandbox_spl where it does not
build, but does not need to be either.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
ARM64 is correctly select'ed in arch/arm/Kconfig, so this line in
the defconfig is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This code does not match the fdt version in fdt.py. When dtoc is unable to
use the Python libfdt library, it uses the fallback version, which does not
widen arrays correctly.
Fix this to avoid a warning 'excess elements in array initialize' in
dt-platdata.c which happens on some platforms.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com>
This fixes a mismatch between the %zu format and the type used on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This fixes a mismatch between the %zu format and the type used on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With sandbox on 32-bit the size_t type can be a little inconsistent. Use
the same type as the caller expects to avoid a compiler warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sandbox is built with 64-bit ints by default. This doesn't work properly on
32-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[NOTE: I took v1 of these patches in, and then v2 came out, this commit
is squashing the minor deltas from v1 -> v2 of updates to c236ebd and
2b9ec76 into this commit - trini]
- Added an additional NULL check, as suggested by Simon Glass to
fit_image_process_sig
- Re-formatted the comment blocks
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
[For merging the chnages from v2 back onto v1]
Signed-off-by: Tom Rini <trini@konsulko.com>
A couple of commits have modified the am33xx/am437x ddr2/ddr3
initialization path to fix certain issues, but have had the side effect
of causing L3 noc errors during initialization. The two commits are:
69b918 "am33xx,ddr3: fix ddr3 sdram configuration"
fc46ba "arm: am437x: Enable hardware leveling for EMIF"
The EMIF_REG_INITREF_DIS_MASK bit still needs to be set for all
platforms. This delays initialization and refresh until a later stage.
The 500us timer can be programmed for platforms that require it
and for platforms that don't require it. It is currently hardcoded
for 400MHz systems. For systems with a higher memory frequency
this needs to be a larger value, and for systems with a lower
memory frequency this can be a lower value. This can be
considered a separate issue and corrected in a later commit.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The delay needs to be before the write to ref_ctrl register
which initiates refreshes. An improper initialization sequence
generates an L3 noc error.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When loading an efi image, we pass it the location it was loaded from.
On file system backends, there are no relative paths, so we should always
pass in absolute ones. For network paths, we may be relative.
This fixes distro booting with grub2 for me when it fetches the grub2 config
file from the loader partition.
Reported-by: york sun <york.sun@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
In certain circumstances it comes in handy to be able to boot into a second
U-Boot. But as of now it is not possible to boot a U-Boot binary that is inside
a FIT image, which is problematic for projects that e.g. need to guarantee a
unbroken chain of trust from SOC all the way into the OS, since the FIT signing
mechanism cannot be used.
This patch adds the capability to load such FIT images.
An example .its snippet (utilizing signature verification) might look
like the following:
images {
firmware@1 {
description = "2nd stage U-Boot image";
data = /incbin/("u-boot-dtb.img.gz");
type = "firmware";
arch = "arm";
os = "u-boot";
compression = "gzip";
load = <0x8FFFC0>;
entry = <0x900000>;
signature@1 {
algo = "sha256,rsa4096";
key-name-hint = "key";
};
};
};
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Tom Rini <trini@konsulko.com>
commit 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid
left under a macro KS2_MSMC_SEGMENT_QM_PDSP which is no longer valid.
This, in effect disabled DMA coherency for QM PDSP.
Given that msmc_k2hkle_common_setup is valid for all K2H/K/L/E SoCs,
the #ifdef should been removed in the first place. Do the same.
Fixes: 1f807a9f32 ("ARM: keystone2: Refactor MSMC macros to avoid #ifdeffery")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A feasible way to communicate certain errors for devices that have no
other way of signalling besides LEDs is to flash these LEDs. For errors
in U-Boot, a script that utilizes the led and sleep commands would be a
practicable way, but currently the sleep command can only delay for an
integral amount of seconds, which is too slow to create an easily
noticeable pattern for flashing LEDs.
Therefore, this patch adds support for fractions (down to .001 seconds)
to the sleep command.
The parsing is kept minimal, simplistic and as robust as possible: After
converting the passed string using simple_strtoul and multiplying it
with 1000, we search for the first dot, convert the three characters
after that into a number (if they are not numbers, we ignore the
fractional part and just use the delay we got from simple_strtoul), and
add this number to the delay.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
nand_do_write_ops() determines if it is writing a partial page with the
formula:
part_pagewr = (column || writelen < (mtd->writesize - 1))
When 'writelen' is exactly 1 byte less than the NAND page size the formula
equates to zero, so the code doesn't process it as a partial write, although
it should.
As a consequence the function remains in the while(1) loop with 'writelen'
becoming 0xffffffff and iterating until the watchdog timeout triggers.
To reproduce the issue on a NAND with 2K page (0x800):
=> nand erase.part <partition>
=> nand write $loadaddr <partition> 7ff
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Enable the NAND controller in the sun5i-r8-chip.dts.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
On some sunxi boards we have NANDs exposing 1664 OOB bytes per page.
Define the CONFIG_SYS_NAND_MAX_ECCPOS value accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NANDs are now exposing 1664 OOB bytes per page. Adjust the
NAND_MAX_OOBSIZE value accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add a full-id entry for the H27QCG8T2E5R‐BCF NAND.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add the NAND controller definition to sun5i.dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We already have an SPL driver for the sunxi NAND controller, now add
the normal/standard one.
The source has been copied from Linux 4.6 with a few changes to make
it work in u-boot.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
The original commit has been slightly reworked to use the fdtdec_xxx()
helpers (instead of the of_xxxx() ones).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
We need some macros to manipulate the NAND controller clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Modern NANDs do not guarantee that data written in raw mode will not
contain bitflips just after writing them. This is fine since the number
of bitflips should be rather low and thus fixable by the ECC engine,
but since we are reading data in raw mode to verify if they match the
input data we cannot prevent failures if some bits are flipped.
The option of using standard mode to verify the data is not acceptable
either, since one of the usage of raw mode is to allow flashing images
that do not respect the standard NAND page layout or the default ECC
config (this is the case on Allwinner platforms, where the ROM code
tests several hardcoded configs, which are not necessarily matching the
NAND characteristics).
Add an extension to the nand write.raw command allowing one to disable
the verification step.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Deassert resets and enable clock signals of xHCI blocks if the
corresponding CONFIG is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to add more board attributes, so the "flags" member will be
handier than separate boolean ones.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sync register macros with Linux code. This will be helpful to
develop the counterpart of Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.
[ Linux commit: 2a4a2aadbaad9dffdb564a2895348f3d8e825416 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Getting this error:
Zynq> sb load hostfs - 100
/home/monstr/data/disk/u-boot/build-zynq_zc706/test.fit
Unknown command 'sb' - try 'help'
because sb command is present only for Sandbox
obj-$(CONFIG_SANDBOX) += host.o
that's why mark this test to be run only at Sandbox
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Commit 17c2987 introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM57xx and DRA7xx high-security (HS) devices that
causes the build to break when that option is not active. Fix this issue
by only building the u-boot_HS.img target when building U-Boot into an
actual FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit e29878f introduces an undesired dependency on CONFIG_SPL_LOAD_FIT
when building U-Boot for AM43xx high-security (HS) devices that causes the
build to break when that option is not active. Fix this issue by only
building the u-boot_HS.img target when building U-Boot into an actual
FIT image.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In raw mode a full sector is to be read even if image covers part of
a sector. Number of sectors are calculated as ROUND_UP(size)/sec_size by FIT
framework. This calculation assumes that image is at the 0th offset of a sector,
which is not true always in FIT case. So, include the image offset while
calculating number of sectors.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When signing images, we repeatedly call fit_add_file_data() with
successively increasing size values to include the keys in the DTB.
Unfortunately, if large keys are used (such as 4096 bit RSA keys), this
process fails sometimes, and mkimage needs to be called repeatedly to
integrate the keys into the DTB.
This is because fit_add_file_data actually returns the wrong error
code, and the loop terminates prematurely, instead of trying again with
a larger size value.
This patch corrects the return value by fixing the return value of
fdt_add_bignum, fixes a case where an error is masked by a unconditional
setting of a return value variable, and also removes a error message,
which is misleading, since we actually allow the function to fail. A
(hopefully helpful) comment is also added to explain the lack of error
message.
This is probably related to 1152a05 ("tools: Correct error handling in
fit_image_process_hash()") and the corresponding error reported here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg217417.html
Signed-off-by: Mario Six <mario.six@gdsys.cc>
