Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Since the SPI flash chip mx25l3205d on this board has 4K-sector
capability, enable it for the envs.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Building sandbox_spl with CONFIG_DEBUG leads to errors due to missing
symbols:
/usr/bin/ld: common/spl/spl_fit.o: in function `spl_fit_upload_fpga':
common/spl/spl_fit.c:595: undefined reference to `fpga_load'
/usr/bin/ld: test/test-main.o: in function `dm_test_post_run':
test/test-main.c:124: undefined reference to `crc8'
/usr/bin/ld: test/test-main.o: in function `dm_test_pre_run':
test/test-main.c:95: undefined reference to `crc8'
collect2: error: ld returned 1 exit status
This is due to -Og not eliminating unused functions.
Add FPGA and CRC8 support to the defconfig. Sandbox tests for
SPL_FPGA and CRC8 should be created. So enabling these setting
is advised anyway.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmP+97wcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyExpB/wLQVjeBM+sEcABzT52
c7qtAvtgl/UbPedYyMz2YorL5BcHsdmBbGfSzBISEc8kLdtAVMTKAaqvN7msaJFX
MwPIZAXWd8cPM0EA7wSyjYDGOvcEzGWF7oxSbeq+j7M2kibvsQLGW7iaY5cjFIzx
QPQ19T2tyX3jrsy8dxCsPivB70vB/3lqiEmCZX2UddsjxrL6Vt2H3k6O+/Ler5wS
/nJIzKLDPc+aDZSv+aevDlJZi1eGkpTHldNaHXqdYILzvnXIQmA6kP0mWPZ9g6wZ
s6ed1N5VeiS4j6oH5Woj3nDKny7P3AKSd9+c/eXfbtdia2D0yBHtiHQauIwNPCd3
wAcH
=/Vn2
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.04 cycle:
This fixes set include one clock index fix for sama7g5 and two board
configuration alignments for pm9g45.
RK3588 has two memory gaps when using 16 GiB DRAM size:
[0x3fc000000 , 0x3fc500000]
and
[0x3fff00000 , 0x3ffffffff]
If the kernel is agnostic to these gaps, accessing the area causes
a SError panic.
Hence, add reserved memory areas in kernel's DTB before booting.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
=> usb start
starting USB...
Bus usb@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fd800000: USB EHCI 1.00
scanning bus usb@fd000000 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus usb@fd800000 for devices... 4 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 04019c9b2e1a58f24ee318c3c123aa5
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
| USB 2.0 Hub
|
+-3 Mass Storage (480 Mb/s, 500mA)
| JetFlash Mass Storage Device 19M7I4ZQFTSC08SU
|
+-4 Human Interface (12 Mb/s, 98mA)
Logitech USB Receiver
Co-developed-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Radxa ROCK 3 Model A support. sync rk3308-rock-pi-s.dts from
Linux 6.2.0-rc7.
ROCK Pi S is RK3308 based SBC from radxa.com. ROCK Pi S has a,
- 256MB/512MB DDR3 RAM
- SD, NAND flash (optional on board 1/2/4/8Gb)
- 100MB ethernet, PoE (optional)
- Onboard 802.11 b/g/n wifi + Bluetooth 4.0 Module
- USB2.0 Type-A HOST x1
- USB3.0 Type-C OTG x1
- 26-pin expansion header
- USB Type-C DC 5V Power Supply
Linux commit commit for the same,
<2e04c25b1320> ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Radxa ROCK 3 Model A support. sync rk3568-rock-3a.dts from Linux 6.2.0-rc7
Board Specifications
- Rockchip RK3568
- 2/4/8GB LPDDR4 3200MT/s
- eMMC socket, SD card slot
- GbE LAN
- PCIe 3.0/2.0
- M.2 Connector
- 3.5mm Audio jack with mic
- HDMI 2.0, MIPI DSI/CSI
- USB 3.0 Host/OTG, USB 2.0 Host
- 40-pin GPIO expansion ports
- USB Type C PD 2.0, 9V/2A, 12V/2A, 15V/2A, 20V/2A
Refer Linux commit <22a442e6586c>
("arm64: dts: rockchip: add basic dts for the radxa rock3 model a")
Signed-off-by: Akash Gajjar <gajjar04akash@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
An external TPL binary is now expected to be provided using ROCKCHIP_TPL
when building RK3568 targets.
This reverts commit 31500e7bcf.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_RAM_PX30_DDR4 got renamed to CONFIG_RAM_ROCKCHIP_DDR4 in commit
26f92be07e ("ram: rockchip: Add common ddr type configs"). Since both
patchsets were merged unbeknownst to the other, the conflict wasn't
detected while testing each patchset individually and could only be
observed after a merge to master branch.
Fixes: c925be73a0 ("rockchip: add support for PX30 Ringneck SoM on Haikou Devkit")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Provide human-readable manufacturer and product names for the
FriendlyELEC NanoPi R4S.
Enable CONFIG_SYSINFO and CONFIG_SYSINFO_SMBIOS by default.
Signed-off-by: Christian Kohlschütter <christian@kohlschutter.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
All Nvidia boards use the same manufacturer, vendor ID and product ID
for the gadgets. Make them the defaults to remove some boilerplate from
the defconfigs.
Inspired by commit e02687bda9 ("sunxi: provide default USB gadget
setup") which did the same for Allwinner boards.
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Signed-off-by: Tom <twarren@nvidia.com>
This file was missed during the conversion process. Add the symbol to
defconfig.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adjust the initial stack pointer address to 0x10000000(256M)
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Display information about CPU and board during start up.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Loading an image via TFTP is often interrupted when retrying more than
10 times, increase the number of retries so that it does not simply stop
the transfer.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
To reduce the code size, CONFIG_V5L2_CACHE was disabled since commit:
ca06444aac
Turing on does not significantly increase the size of u-boot-spl.bin,
so we enable it by default to improve performance.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Sheevaplug board has 512K CONFIG_BOARD_SIZE_LIMIT. Recently, DM_SERIAL has
pushed the image size a few hundred bytes over that limit. So explicitly
deselect some configs that are unrelated to this board
(and gain back a bit over 2K).
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Both U-boot and Linux kernel have grown over the last releases
and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image
on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel
look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define
CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults
to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
as Tom suggested get rid of CFG_EXTRA_ENV_SETTINGS and
enable CONFIG_ENV_SOURCE_FILE and use text file
board/socrates/socrates.env
which contains the default environment. While at it,
cleanup the default Environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As explained by Philippe Schenker, I was misinterpreting what happened
in the case where we do not set LMB_USE_MAX_REGIONS and so had
re-introduced the problem I was attempting to more widely resolve.
This reverts commit 007ae5d108.
Reported-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop use of the distro scripts and use standard boot instead.
Enable BOOTDEV_FULL just for convenience, although this does add quite a
bit to the size.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
am335x_evm_defconfig is used for BeagleBone Black, popular single board
computer with wide extension support. Enable CONFIG_CMD_EXTENSION by default
since extension detection is already implemented for am335x.
Also run make savedefconfig for am335x_evm_defconfig
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
setup MTD partitioning through mtdparts variable
and set it to:
mtdparts=fe0000000.nor:13312k(system1),13312k(system2),5120k(data),128k(env),128k(env-red),768k(u-boot)
and pass this to linux per kernel commandline.
Signed-off-by: Heiko Schocher <hs@denx.de>
convert socrates board to use MPC85XX_HAVE_RESET_VECTOR and
disable CONFIG_OF_BOARD and use common u-boot.dtsi for
creating u-boot-dtb.bin.
Signed-off-by: Heiko Schocher <hs@denx.de>
current mainline does not work on socrates board. To
get it back up working, there are some updates needed
in socrates_defconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixes: 94633c36f9 ("net: Make DM_ETH be selected by NETDEVICE")
Fixes: 2f8a6db5d8 ("Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig")
