Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
While at this enable the DM and TIFS UARTs for programming pinmux
since they are marked reserved by board.dts
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
k3-am62* SoC dtsi files now provide the following:
bootph-all: dmss secure_proxy_main dmsc k3_pds k3_clks k3_reset
main_pmx0 main_timer0 mcu_pmx0 wkup_conf chipid
bootph-pre-ram: secure_proxy_sa3 main_esm mcu_esm
Drop these from board r5 and u-boot.dtsi files as these are duplicate in
them now.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
either the definitions from main.dtsi OR duplication from u-boot.dtsi
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add OSPI Support such that this device can boot up using OSPI Flash.
Also can use the flash for other purposes if required from uboot.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
