Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save and use the FDT address provided by TF-A in r2 at boot time
(it is NT_FW_CONFIG = Non Trusted Firmware configuration file)
Address is saved in save_boot_params(), called by start.S
and the used DTB is gd->fdt_blob = board_fdt_blob_setup().
If dtb is not provided or invalid, U-Boot use as fallback
the builtin DTB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add weak implementation of board_early_init_f() hook into the
STM32MP1 SPL. This can be used to read out e.g. configuration
straps before initializing the DRAM.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
This function is only relevant to the MMC driver so calling it
spl_boot_partition() might be confusing. Rename it to
spl_mmc_boot_partition() to make its purpose more clear (and bring
it in line with spl_mmc_boot_mode()).
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The function's name is misleading as one might think it is used
generally to select the boot-mode when in reality it is only used by the
MMC driver to find out in what way it should try reading U-Boot Proper
from a device (either using a filesystem, a raw sector/partition, or an
eMMC boot partition).
Rename it to spl_mmc_boot_mode() to make it more obvious what this
function is about.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts the workaround introduced by the
commit 16fec9b0bc ("stm32mp1: remove the imply BOOTSTAGE")
As the bootstage alignment issue is now solved.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Define FMC2 base address, for use in board files, until there is an
actual FMC2 bus driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This path allows to set the cntfrq register of targeted cpu.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update the kernel device tree for STM32MP15x product lines according
the used soc and its part number, when CONFIG_OF_SYSTEM_SETUP is activated:
- STM32MP15XA hasn't Crypto (cryp1/2)
- STM32M151 and STM32M153 hasn't 3D GPU and DSI host
- STM32M151 hasn't CAN FD and has single A7
For example:
FDT: cpu 1 node remove for STM32MP151AAA Rev.B
FDT: can@4400e000 node disabled for STM32MP151AAA Rev.B
FDT: gpu@59000000 node disabled for STM32MP151AAA Rev.B
FDT: dsi@5a000000 node disabled for STM32MP151AAA Rev.B
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_soc_name to get a string with the full name
of the SOC "STM32MP15xxx Rev.x"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add the SMC code and operation for trace on errors.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove the test offs < 0 , as offs is unsigned.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
In function ‘stm32mp_bsec_read’:
arch/arm/mach-stm32mp/bsec.c:368:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
368 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
In function ‘stm32mp_bsec_write’:
arch/arm/mach-stm32mp/bsec.c:405:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
405 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Correct the dependency for STM32 ETZPC protection, linked to SOC
STM32MP identified by CONFIG_STM32MP15x and not linked to
CONFIG_TARGET_STM32MP1 (no more existing).
This patch fix an issue introduced by commit 846254888e ("stm32mp1:
split board and SOC support for STM32MP15x family").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Rev.Z of STM32MP15x cpu.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Let board code override setup_mac_address(), which is useful e.g. if the
board derives the MAC address from another source, like an I2C EEPROM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The main prompt for this (defined in /Kconfig) is visible at all times,
which means there's no reason to have an additional, machine-specific
prompt to set the same option.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reset ResourceTableAddress and CoprocessorState at cold boot, preserve
these values at standby wakeup.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the backup register #17 as coprocessor resource table address and
backup register #18 as coprocessor state.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch is only a temporarily workaround for crash introduced by
commit ac9cd4805c ("bootstage: Correct relocation algorithm").
The crash occurs because the bootstage struct is not correctly aligned
when BOOTSTAGE feature is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate by default the command CLS (clear screen);
this command used in pxe or sysboot command (DISTRO support)
when the "menu background" keyword is present.
This patch avoid the warning "Unknown command 'cls'"
with extlinux.conf:
# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
MENU BACKGROUND /splash.bmp
TIMEOUT 20
DEFAULT stm32mp157c-ev1-emmc
LABEL stm32mp157c-ev1-emmc
KERNEL /uImage
FDT /stm32mp157c-ev1.dtb
APPEND root=/dev/mmcblk1p4 rootwait rw console=ttySTM0,115200
...
Retrieving file: /mmc0_stm32mp157c-ev1_extlinux/extlinux.conf
614 bytes read in 36 ms (16.6 KiB/s)
Retrieving file: /splash.bmp
46180 bytes read in 40 ms (1.1 MiB/s)
Unknown command 'cls' - try 'help'
Select the boot mode
1: stm32mp157c-ev1-sdcard
...
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since the commit 8729b1ae2c ("misc: Update read() and
write() methods to return bytes xfered"); The misc bsec driver
need to be adapted to reflect the number of transferred bytes.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the boot for NOR, SPL load U-Boot.img at offset
CONFIG_SYS_SPI_U_BOOT_OFFS = 0x80000.
It is the start address of mtd partition ssbl in nor.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Depending on backup register value, we maintain the debug unit
powered-on for debugging purpose.
Only BUCK1 is required for powering the debug unit, so revert
the setting for all the other power lanes, except BUCK3 that
has to be always on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This is a generic implementation. Add CONFIG_SYSRESET_CMD_POWEROFF
to signal when we need it. Enable it from the STPMIC1 config and in
sandbox.
The config flag is transitionary, that is it can be removed after all
poweroff implementations use sysreset, and just have CMD_POWEROFF depend
on sysreset.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
It seems that SYSRESET_POWER_OFF was added recently, and all previous code
used SYSRESET_POWER for poweroff. SYSRESET_POWER is supposed to be a
PMIC-level power cycle, not a poweroff.
(Comment by Simon Glass)
SYSRESET_POWER means to do a power reset (removing and reinstating all power)
SYSRESET_POWER_OFF means to turn the device off and leave it off
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
(Update comment to help understand the patch)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch solves the following warnings:
arch/arm/mach-stm32mp/psci.c:
warning: no previous prototype for ‘psci_set_state’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_arch_cpu_entry’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_features’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_version’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_affinity_info’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_migrate_info_type’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_on’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_cpu_off’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_reset’ [-Wmissing-prototypes]
warning: no previous prototype for ‘psci_system_off’ [-Wmissing-prototypes]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/bsec.c: In function 'stm32mp_bsec_read':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (offset >= STM32_BSEC_OTP_OFFSET) {
^~
arch/arm/mach-stm32mp/bsec.c: In function 'stm32mp_bsec_write':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (offset >= STM32_BSEC_OTP_OFFSET) {
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/cpu.c:378:16: warning: comparison between signed
and unsigned integer expressions [-Wsign-compare]
if (instance > ARRAY_SIZE(serial_addr))
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
U-Boot should disable nodes in device tree if needed according
ETZPC status in ft_system_setup().
ETZPC itself use an array on addresses to do the match between the status
bits and the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Without newline, the error message appears for non prgrammed OTP boards
looks messsy. Hence add it to look more clean.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the needed configurations for bootstage and
activate bootstage command.
BOOTSTAGE_REPORT is not activated by default.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use SGI0 interruption and TAMP_BACKUP_MAGIC_NUMBER
to synchronize the core1 boot sequence requested by
core0 in psci_cpu_on():
- a initial interruption is needed in ROM code after
RCC_MP_GRSTCSETR_MPUP1RST (psci_cpu_off)
- the ROM code set to 0 the 2 registers
+ TAMP_BACKUP_BRANCH_ADDRESS
+ TAMP_BACKUP_MAGIC_NUMBER
when magic is not egual to
BOOT_API_A7_CORE0_MAGIC_NUMBER
This patch solve issue for cpu1 restart in kernel.
echo 0 > /sys/devices/system/cpu/cpu1/online
echo 1 > /sys/devices/system/cpu/cpu1/online
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig as it is already done for zynq arch in
commit 01aa5b8f05 ("Kconfig: Move config
SYS_MALLOC_LEN to Kconfig for zynq")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cosmetic cleanup in mach-stm32mp Kconfig
- remove duplicated SPL_DRIVERS_MISC_SUPPORT
- update help for TARGET_STM32MP1
- set value for NR_DRAM_BANKS
- remove one comment as DEBUG_UART is deactivated by default
- include board Kconfig at the end of the file
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- export the function get_bootmode() and reused it in spl code
- manage uart instance by alias (prepare v4.19 binding)
- solve issue on nand instance
- restore console for uart boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As BSEC is secure aware, all register access need to be done
by TF-A for TRUSTED boot chain, when U-Boot is executed in
normal world.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update generation of spl binaries
- continue to generate all SPL files in spl sub-directory
- copy in root folder the needed file for user (YOCTO, buildroot):
u-boot-spl.stm32
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Deploy u-boot-spl.stm32 binary in u-boot root folder like
the rest of the boards.
This makes it more streamlined when building in Yocto, Buildroot etc..
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
In some STM32 SoC packages, GPIO bank has not always 16 gpios.
Several cases can occur, gpio hole can be located at the beginning,
middle or end of the gpio bank or a combination of these 3
configurations.
For that, gpio bindings offer the gpio-ranges DT property which
described the gpio bank mapping.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET, so can use
CONFIG_IS_ENABLED(DM_RESET) checking in reset.h later.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use OTP57 and 58 for MAC address
- OTP57 = MAC address bits [31:0]
- OTP58 = MAC address bit [47:32] stored in OTP LSB's
Use manufacture information in OTP13 to OTP15 to build unique
chip id saved in env variable "serial#"
(used for USB device enumeration)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add a MISC driver with read and write access to BSEC IP
(Boot and Security and OTP control)
- offset 0: shadowed values
- offset 0x80000000: OTP fuse box values (SAFMEM)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The register TAMP_BOOT_CONTEXT is already updated in
get_bootmode() in cpu.c and no need to be done
twice.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add the needed information to enable the debug uart
to have printf before the serial driver probe
(so before probe for clock, pincontrol and reset drivers)
To enable the debug on uart 4 (default console):
+ CONFIG_DEBUG_UART=y
+ CONFIG_DEBUG_UART_STM32=y
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This driver binds and manages the following regulator of
SoC's PWR block :
- reg11
- reg18
- usb33
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add PSCI v1.0 support for Linux and manage PSCI state
for each CPU (affinity 0 level) with all mandatory functions:
- PSCI_VERSION
- CPU_SUSPEND
- CPU_OFF
- CPU_ON
- AFFINITY_INFO
- SYSTEM_OFF
- SYSTEM_RESET
- PSCI_FEATURES
and 1 optional to avoid Linux warning
- MIGRATE_INFO_TYPE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: CITOOLS <smet-aci-reviews@lists.codex.cro.st.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Bootrom loads SPL from SDCARD or eMMC
according BootPin selection.
Then SPL loads U-Boot on the same mmc device
with the following predefined GPT partitioning:
on SDCARD: gpt partitioning
1: SPL
2: SPL#2
3: U-Boot
4: bootable partition
on eMMC:
The 2 boot partitions are used for SPL (2 copy)
boot1: SPL
boot2: SPL#2
The user partition use gpt partitioning
1: U-Boot
2: bootable partition
This patch select the correct SPL partition
(3 for SDCARD on mmc0 and 1 for eMMC on mmc1)
according the BootRom information saved in TAMP register
and based on configuration flasg:
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
=> for BOOT_DEVICE_MMC1 or mmc 0 in U-Boot
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2 (new)
=> for BOOT_DEVICE_MMC2 or mmc 1 in U-Boot
And the correct boot_targets is selected according the environment
variables boot_device and boot_instance, with preboot command,
to search the bootable partition with kernel on this device
(generic distro support).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
SPL copy BootRom boot mode information
in TAMP register 21.
This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
(DISTRO activated)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
