Add a command to load SEAMA (Seattle Image), a NAND flash
on-flash storage format.
This type of flash image is found in some D-Link routers such
as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and
DCH-M225, as well as in WD and NEC routers on the ath79
(MIPS), Broadcom BCM53xx, and RAMIPS platforms.
This U-Boot command will read and decode a SEAMA image from
raw NAND flash on any platform. As it is always using big endian
format for the data decoding is always necessary on platforms
such as ARM.
The command is needed to read a SEAMA-encoded boot image on the
D-Link DIR-890L router for boot from NAND flash in an upcoming
port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx)
architecture.
A basic test and documentation is added as well. The test must
be run on a target with NAND flash support and at least one
resident SEAMA image in flash.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the issue in commit 46c9016 ("env: mcc: Drop unnecessary #ifdefs")
If CONFIG_SYS_REDUNDAND_ENVIRONMENT is not defined, the offset value
becomes undetermined, so write env to unexpected offset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If image file is stored on flash partition then it contains padding, which
is not part of the image itself. Image data size is stored in the image
header. So use image size from the header instead of expecting that total
image file size is size of the header plus size of the image data. This
allows dumpimage to parse image files with padding (e.g. dumped from flash
partition).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before reading image header, verify that image size is at least size of
the image header.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpimage type requires only that two first 32-bit words of data file are
non-zero. So basically every random data file can be guessed and verified
as gpimage. So completely skip gpimage type from image autodetection code
to prevent lot of false positive results. Data file with gpimage type can
be still verified and parsed by explicitly specifying -T gpimage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop use of the distro scripts and use standard boot instead.
Enable BOOTDEV_FULL just for convenience, although this does add quite a
bit to the size.
Signed-off-by: Simon Glass <sjg@chromium.org>
This supports reading a kernel and ramdisk from qfw, then loading it with
either the booti or bootz commands.
For now this uses the existing booti and bootz commands, rather than
trying to call that functionality directly (e.g. do_bootm_states()). It
does not require the HUSH parser though, which helps a little with size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a bootdev device for qfw so that it can be used with standard boot.
This simply checks for the correct method and then does the read. Most of
the other logic is handed in a new bootmeth driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is currently in the cmd/ file but we want to call it from a driver.
Move it into a common place. Tidy up the header-file order while we are
here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses casts all over the place. Use the correct type so that these
can be avoided, as is done with other commands. Also simplify a few
conditionals.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to support a basic set of filesystems for booting to work in most
cases. Add these in via a new option, letting the board disable them
individually (for space reasons) if desired.
This enables the filesystem commands as well as the actual functionality,
even though bootstd is quite happy to use ext4 without the ext4 command.
Further work would be needed to disintangle this and reduce code size.
Add several other options as well, providing sensible defaults.
We cannot enable this by default, since it expands the size of many
boards quite a lot.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present virtio tries to attach QEMU services to a bootdev device, which
cannot work. Add a check for this.
Also use bootdev_setup_sibling_blk() to create the bootdev device, since
it allows the correct name to be used and bootdev_get_sibling_blk() to
work as expected.
The bootdev is not created on sandbox since it does have a real virtio
device and it is not possible to read blocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a60f7a3e35 ("bootstd: Add a virtio bootdev")
Reported-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In some cases the block device is obtained but is not probed, since it
is a sibling of the bootdev. Make sure it is probed, so it can be used
without any trouble.
This fixes a bug with virtio, where the device is accessed before it has
been set up by the virtio uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 201417d700 ("bootstd: Add the bootdev uclass")
Reported-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is sometimes useful to have one without the other, e.g. on a device
without a display, since at present the expo feature requires CONFIG_VIDEO
to be enabled.
Update the Makefile and bootflow command to support this, as well as the
EXPO dependency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to log things related to filesystems. Add a new
category and place it at the top of one of the FAT files.
Signed-off-by: Simon Glass <sjg@chromium.org>
am335x_evm_defconfig is used for BeagleBone Black, popular single board
computer with wide extension support. Enable CONFIG_CMD_EXTENSION by default
since extension detection is already implemented for am335x.
Also run make savedefconfig for am335x_evm_defconfig
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
This family of platforms typically has a USB port, and so attempting to
boot from it, and making it first, will provide a better overall user
experience.
Signed-off-by: Tom Rini <trini@konsulko.com>
we need to set initrd_high to get fitimage booting.
Without, U-Boot drops when booting fitimage:
ERROR: Failed to allocate 0x59a0b6 bytes below 0x800000.
ramdisk - allocation error
bootm - boot application image from memory
Signed-off-by: Heiko Schocher <hs@denx.de>
setup MTD partitioning through mtdparts variable
and set it to:
mtdparts=fe0000000.nor:13312k(system1),13312k(system2),5120k(data),128k(env),128k(env-red),768k(u-boot)
and pass this to linux per kernel commandline.
Signed-off-by: Heiko Schocher <hs@denx.de>
convert socrates board to use MPC85XX_HAVE_RESET_VECTOR and
disable CONFIG_OF_BOARD and use common u-boot.dtsi for
creating u-boot-dtb.bin.
Signed-off-by: Heiko Schocher <hs@denx.de>
U-Boot build process for socrates board produces final U-Boot binary in
file u-boot-socrates.bin (by binman) And as a bonus it produces two
unusable broken binaries u-boot-dtb.bin and u-boot.bin (by Makefile).
Clean this up, so final U-Boot binary is in u-boot-dtb.bin
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
current mainline does not work on socrates board. To
get it back up working, there are some updates needed
in socrates_defconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixes: 94633c36f9 ("net: Make DM_ETH be selected by NETDEVICE")
Fixes: 2f8a6db5d8 ("Finish conversion of CONFIG_SYS_CLK_FREQ to Kconfig")
This was added by mistake and renders the function useless. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 33c60a38bb ("trace: Use notrace for short")
Reported-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
As MDIO driver does not support Driver Model, the
pinctrl settings in the MDIO node will not
be applied resulting in PHY not being detected.
To workaround this we add the MDIO pinctrl in
the CPSW3G node in the -u-boot.dtsi file.
Add the missing MDIO and RGMII pinctrl nodes in
k3-am642-r5-evm.dts
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are no differences for the different 832x targets we have in
the header defined with SYS_CONFIG_NAME. So we can join the five
headers to a single file.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Next step to get rid of the header files in icnlude/configs. Move
most of the defines to km83xx.c directly. Some remaining defines
which should go to Kconfig are moved to km-mpc83xx.h for now.
Also remove some unused defines and move one define to powerpc.env
as we only need it there.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
Set splash screen related env variables. Default splash source is
set to mmc where user is expected to keep bmp in compressed format
with name ti.gz on first partition of mmc.
Splash file will be uncompressed to DDR at address 0x82000000 and
splash position is set to middle of screen.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Use .env file for setting board related environment variables,
in place of am62x_evm.h file. Except for BOOTENV settings, as
config_distro_boot.env file doesn't exist.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This test will block compilation of the entire test suite
on platforms without USB support. Make the extern
"usb_started" conditional on USB host or gadget and
define a dummy flag if neither is enabled.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Required as Elf_Sym in tools/prelink-riscv.inc. I assume people have
been using an OS-supplied elf.h, but macOS doesn't have that.
Taken from
https://github.com/torvalds/linux/blob/v6.1/include/uapi/linux/elf.h
Signed-off-by: KaDiWa <kalle.wachsmuth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix shell error:
/bin/sh: line 0: [: too many arguments
for the darwin major/minor version check.
It seems for os_x_before for some reason DARWIN_MAJOR_VERSION and
DARWIN_MINOR_VERSION are empty. To fix this set DARWIN_MAJOR_VERSION
and DARWIN_MINOR_VERSION to be evaluated once so the value is retained.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When adding reserved memory areas from the EFI memory map set the NOMAP
flag when applicable. When this isn't done adding "no-map" flagged entries
from the fdt after receiving the same from the EFI memory map fails due
to non-matching flags.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
The LMB code allows for picking a hard limit on the number of regions it
can know of, or to dynamically allocate these regions. The reason for
this choice is to allow for the compiler to perform a size optimization
in the common case. This optimization however, is very small, ranging
from 196 bytes to 15 bytes saved, or in some cases, being larger. Now
that we also have more regions covered by LMB (in order to protect
various parts of our self at run time), the default of 8 is also much
easier to hit and leads to non-obvious error messages (which imply that
an area is protected, not that we're out of areas to add to the list).
Switch to the dynamic use as the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
- make simple panel independent of backlight
- add ofnode panel timing decode functions with test
- add TIDSS video driver and AM62x splash screen
- add TI logo
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY96rpQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXBXnAJ9hs98w0Azf1VpfhfGnV0IETCzu7ACfSA8X2qck
oldzKOBwb247sPVc2X0=
=0jSk
-----END PGP SIGNATURE-----
Merge tag 'video-20230204' of https://source.denx.de/u-boot/custodians/u-boot-video
- restore TI AM335x LCDC driver with DM support
- make simple panel independent of backlight
- add ofnode panel timing decode functions with test
- add TIDSS video driver and AM62x splash screen
- add TI logo
The default splashfile name saved is ti.gz. User can use these
logo files and use it to test splash screen.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
