There are different parts from one SoC. Take i.MX6ULL for example,
some part might not have ENET, some might have; some might not have
USB, some might have. The information could be got from OCOTP,
to make one image support the different parts, we need runtime
disable linux kernel dts node and uboot driver probe if the
corresponding module not exists in the part.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add REVC informaiton.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the new flags DCACHE_DEFAULT_OPTION to define the default
option to use according the compilation flags
CONFIG_SYS_ARM_CACHE_*.
This new compilation flag allows to simplify dram_bank_mmu_setup()
and can be used as third parameter (option=dcache option to select)
of mmu_set_region_dcache_behaviour function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move CONFIG_SYS_ARM_CACHE_WRITETHROUGH and
CONFIG_SYS_ARM_CACHE_WRITEALLOC into Kconfig done by moveconfig.py.
Kconfig uses a choice between the 3 values supported in U-Boot,
including the new configuration CONFIG_SYS_ARM_CACHE_WRITEBACK
(the default configuration).
The patch also avoids to select simultaneously 2 configurations.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the latest SCFW API with below commit
6dcd0242ae7a53ac ("SCF-105: Revert accidental change") to add
interfaces for PM resource reset and read/write SNVS security
violation and tamper DGO registers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The fracpll decoding is using the bit definitions for int pll. Most of
them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK
for fracpll and correct all bit definitions in fracpll decoding.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For ARM core clock, there are two input branches, and can select via mux:
one from ARM PLL directly, second from CCM A53 clock root.
Currently we are using second branch. But IC confirmed the CCM A53 root
signoff timing is 1Ghz, so we should switch to input from ARM PLL directly.
This patch fixes the CORE SEL slice configuration and switch ARM clock
to ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update clock root table to let it be easy to configure clock at
very early stage. Also the core_sel mux parent should be A53 CLK
root and ARM PLL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update is_imx6ull helper to include i.MX6ULZ SoC. i.MX6ULZ could
share same macro, then we no need to add is_imx6ulz in various drivers.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MP use 0x182 as its ID, so 0xff is not valid to get the cpu type,
extend it to 0x1ff.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
As a preparation for turning reserve_mmu into an arch-specific variant,
introduce arm_reserve_mmu on ARM. It implements the default routine for
reserving memory for MMU TLB and needs to be weakly defined in order to allow
for machines to override it.
Without this decoupling, after introducing arch_reserve_mmu, there would be two
weak definitions for it, one in common/board_f.c and one in
arch/arm/lib/cache.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The i.MX6DP and i.MX6QP incorporate NoC interconnect logic
which needs to be configured in order to use external DDR memory.
This patch enables the SPL to configure the necessary registers
in accordance with the NXP engineering bulletin EB828.
Co-developed-by: Filip Brozović <fbrozovic@gmail.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This commit removes the programming sequence that enables PLLE and UPHY
PLL hardware power sequencers. Per TRM, boot software should enable PLLE
and UPHY PLLs in software controlled power-on state and should power
down PLL before jumping into kernel or the next stage boot software.
Adds call to board_cleanup_before_linux to facilitate this.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
VOP display endpoint pipeline configuration differs
between rk3288 vs rk3399.
These VOP pipeline configuration depends on how the
different display interfaces connected in sequence to
IN and OUT ports like for,
RK3288:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_hdmi: endpoint@1 {
reg = <1>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_lvds: endpoint@2 {
reg = <2>;
remote-endpoint = <&lvds_in_vopb>;
};
vopb_out_mipi: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi_in_vopb>;
};
};
RK3399:
vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_mipi: endpoint@1 {
reg = <1>;
remote-endpoint = <&mipi_in_vopb>;
};
vopb_out_hdmi: endpoint@2 {
reg = <2>;
remote-endpoint = <&hdmi_in_vopb>;
};
vopb_out_mipi1: endpoint@3 {
reg = <3>;
remote-endpoint = <&mipi1_in_vopb>;
};
vopb_out_dp: endpoint@4 {
reg = <4>;
remote-endpoint = <&dp_in_vopb>;
};
};
here, HDMI interface has endpoint 1 in rk3288 and 2 in rk3399.
The rockchip vop driver often depends on this determined endpoint
number and stored in vop_mode. So based on this vop_mode the bpp
and pin polarity would configure on detected display interface.
Since, the existing driver using rk3288 vop mode settings enabling
the same will result wrong display interface configuration for rk3399.
Add the patch for fixing these vop modes for rk3399.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Cortina CAxxxx GPIO driver maintains DM_GPIO support
across different CPU ISA in the CAxxxx Soc Family; Not just ARM.
Therefore, it is not desirable to split out and maintain separete
gpio header file for each CPU architecture.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add cpu reset cause in common cpu-info file.
This would help to print the reset cause for
various resets.
Right now it support rk3288, rk3399. rest of rockchip
platforms doesn't have reset cause support ye but this
code is more feasible to extend the same.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Few of the rockchip family SoC atleast rk3288,
rk3399 are sharing some cru register bits so
adding common code between these SoC families
would require to include both cru include files
that indeed resulting function declarations error.
So, create a common cru include as cru.h then
include the rk3399 arch cru include file and move
the common cru register bit definitions into it.
The rest of rockchip cru files will add it in future.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Subsystems such as USB expect dma_map_single() and dma_unmap_single() to
do dcache flush/invalidate operations as required. For example, see
see drivers/usb/gadget/udc/udc-core.c::usb_gadget_map_request().
Currently drivers do this locally, (see drivers/usb/dwc3/ep0.c,
drivers/mtd/nand/raw/denali.c etc..)
Update arch specific dma_map_single() and dma_unmap_single() APIs to do
cache flush/invalidate operations, so that drivers need not implement
them locally.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add an arch-specific handoff header so that we can use the HANDOFF feature
on arm devices.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Exports the serdes configuration as an environment variable for LS gen 3
SoCs, so it can be used in u-boot command line. It should particularly
be useful for applying Linux DT overlays for the given serdes
configuration.
This code is called from arch_misc_init and not from the existing
serdes_init function because it depends on U-Boot environment being set
up.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm68360.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function is only used on ARM devices so does not belong in the global
common header file. Move it to an ARM header.
Signed-off-by: Simon Glass <sjg@chromium.org>
SoC base addresses should better go into a common SoC file instead
of repeating the definition in each board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The QorIQ eSDHC controller supports two reference clocks. They are
platform clock and periperhal clock. The global variable sdhc_clk
has already been used for platform clock.
This patch is to add another global variable sdhc_per_clk for
periperhal clock, which provides higher frequency and is required
to be used for SD UHS and eMMC HS200/HS400 speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Current U-Boot has only support for psci reset.
Adding support for arm psci reset2 allows passing of reset level
and other platform sepcific parameters like strap settings
to lowlevel psci implementation.
Signed-off-by: Rajesh Ravi <rajesh.ravi@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Programs the following:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
i.MX8MP has similar architecture as i.MX8MN, but it has different
clk root and index, so add that to make i.MX8MP could use
the non-dm clock driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
I tried clearing a bit by writing to hw_clkctrl_gpmi_clr, then
busy-waiting for it to actually clear. My board hung. The data sheet
agrees, these registers do not have _set, _clr, _tog, so fix up the
definitions. git grep -E 'clkctrl_(gpmi|ssp[0-9])_' says that nobody
uses those non-existing ops registers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.
Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Currently imx-specific bootaux command doesn't support ELF format
firmware for Cortex-M4 core.
This patches introduces a PoC implementation of handling elf firmware
(load_elf_image_phdr() was copy-pasted from elf.c just for PoC).
ELF64 binaries isn't supported yet.
This has the advantage that the user does not need to know to which
address the binary has been linked to. However, in order to handle
and load the elf sections to the right address, we need to translate the
Cortex-M4 core memory addresses to primary/host CPU memory
addresses (Cortex A7/A9 cores).
This allows to boot firmwares from any location with just using
bootaux, e.g.:
> tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}
Similar translation table can be found in the Linux remoteproc
driver [1].
[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Enable AHB support for Flexspi controller interface meaning
memory can be accessed via md command using absolute addresses
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hardware comes out of reset with implicit values, but these are outside
the accepted range for Layerscape gen 3 chassis spec used on LS1028A.
Allocate different IDs and fix up Linux DT to use them.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
USB3.0 Receiver needs to enable fixed equalization
for each of PHY instances in an SOC. This is similar
to erratum A-009007, but this one is for LX2160A,
and the register value is different.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
struct sunxi_prcm_reg is naturally packed. There is no need to define it as
packed. Defining it as packed leads to compilation errors with GCC 9.2.1:
CC arch/arm/lib/reloc_arm_efi.o
arch/arm/cpu/armv7/sunxi/psci.c: In function ‘sunxi_cpu_set_power’:
:qarch/arm/cpu/armv7/sunxi/psci.c:163:21: error: taking address of packed
member of ‘struct sunxi_prcm_reg’ may result in an unaligned pointer value
[-Werror=address-of-packed-member]
163 | sunxi_power_switch(&prcm->cpu_pwr_clamp[cpu], &prcm->cpu_pwroff,
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Remove __packed attribute from struct sunxi_prcm_reg.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
-----BEGIN PGP SIGNATURE-----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=L2zo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191209' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.01
-----------------
- imx8qxp_mek: increase buffer sizes and args number
- Fixes for imx7ulp
- imx8mm: Fix the first root clock in imx8mm_ahb_sels[]
- colibri_imx7: reserve DDR memory for Cortex-M4
- vining2000: fixes and convert to ethernet DM
- imx8m: fix rom version check to unbreak some B0 chips
- tbs2910: Disable VxWorks image booting support
Make the PMU LDO configuration interface available to board code,
so that board code can reconfigure the internal LDOs of the SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Eric Nelson <eric@nelint.com>
i.MX 7's Cortex-M4 core can run from DDR and uses DDR memory for
the rpmsg communication. Both use cases need a fixed location of
memory reserved. For the rpmsg use case the reserved area needs
to be in sync with the kernel's hardcoded vring descriptor location.
Use the linux,usable-memory property to carve out 1MB of memory
in case the M4 core is running. Also make sure that the i.MX 7
specific rpmsg driver does not get loaded in case we do not carve
out memory.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.
The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.
The RK3288 keep the current functions.
RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some generic PX30 SoMs found in the wild use UART3 as their debug output
instead of UART2 (used for MMC) and UART5.
Make it possible to use UART3 as early debug output, with the associated
clock and pinmux configuration. Two sets of output pins are supported (M0/M1).
Future users should also note that the pinmux default in the dts is to use
the M1 pins while the Kconfig option takes M0 as a default.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
According to the PX30 TRM, the iomux registers come first, before the pull
and strength control registers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Although layerscape platforms reuse mxc_get_clock() of i.MX platforms,
eSDHC clock getting do not have to use it. It uses global data
gd->arch.sdhc_clk directly in fsl_esdhc driver. Even there are more
than one eSDHC controllers on SoC, they use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
RK3308 is a quad Cortex A35 based SOC with rich audio
interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which
designed for intelligent voice interaction and audio
input/output processing.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Common PLL setup function, compatible with different SOC.
Mainly for the subsequent new SOC use.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_reset_bind() already does the needed init for the reset
registers, only referenced the wrong cru structure.
So we can get rid of the open-coded reset init and just fix
the correct cru reference.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add core architecture code to support the px30 soc.
This includes a separate tpl board file due to very limited
sram size as well as a non-dm sdram driver, as this also has
to fit into the tiny sram.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 contains 2 separate clock controllers, pmucru and cru.
Add drivers for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add headers needed by the upcoming px30 support, including two
new dt-binding headers taken from the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the calculation of the stride to support all the DRAM case.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.
For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The noc register bit definition may be the same for different SoC while
the offset of the register may be different, add the struction
definition as common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_phy_px30.c is based on PX30 SoC, the functions are common
for phy, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_pctl_px30.c is based on PX30 SoC, the functions are common
for controller, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Since we have new DRAM type and to support different DRAM size in different
CS, we need more bits, so introduce sys_reg3 to record the info.
Note that the info in sys_reg3 is extension to sys_reg2 and the info in
sys_reg2 is the same as before. We define the DRAM_INFO with sys_reg3 as
VERSION2.
All the ENC macro are moved to sdram_common.h since the sdram.c only
need to do the info decode.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The sdram.h suppose to be helper file for sdram.c which including dram
size decode and some u-boot related dram init interface, and all
structure and function for dram driver move to sdram_common.h
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rename sdram_common.c in arch/arm/mach-rockchip to sdram.c;
so that we can use the file name sdram_common.c in dram driver for
better understand the code;
clean the related file who has use the header file at the same time.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The header file sdram.h is used for rk3288 and similar SoCs, rename it
to make it more understandable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
