While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.
All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.
These results have been confirmed with tools/moveconfig.py.
Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some options like TPL_SYS_THUMB_BUILD, TPL_USE_ARCH_MEMCPY
and TPL_USE_ARCH_MEMCPY are needed for TPL build in 32bit arm.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add platform code and DTs for Renesas RZ/A1 R7S72100 SoC.
Distinguishing feature of this SoC is that it has up to
10 MiB of on-SoC static RAM (SRAM).
The DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Select the PL310 UCLASS_CACHE driver for SoCFPGA.
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----
iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlzDBtoPHHNiYWJpY0Bk
ZW54LmRlAAoJECjE2NMq1et3UpQL/ipaUejQOOr00oOgUBQqt3JCPZ7KNu8ruih/
nIFUDrI8nP+4psaOhRp1sEPFJUxUjdIqODeAZD8zrlEi1pXNAgPWYrFRfbz54bzw
jLsqqMz1/djQseLydQTcqZTSz8Ys7o+8OfKH64fdsZn+y9no9tHBN5hz5qWdXexN
kbyykkg8TJC3eUyRZqKuULOqzDV9BAdASOXu7UTa04sEekLdVvS2+zkUdB6UVZTN
LOAzm+7xY8Tey1BZxLuZUJDpHzFEMvPvlbbQRrxeDn/feZJwNgIP6hGcMeVOwOIf
KEwFn/m/HI2JWS4taXb5aT+v3xmiQvyCC3jNW0XTf5rq02pbfgyPsVhGQIGyU2yY
Fj7zIN7hVCLJNBpctvXyuAd1MjOlGEPIrHNjRnIZjtr7/iA1AIRn7Hg4cGNCHw6V
5gdza3B/xFODN+Ts6O+UVIukI61MJ6mGGdNCueOnWDviNROOL82D7Jh02KfNNNxR
q+yPsHSpo6rC1MGXv4SOReZtgpng/w==
=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
K3 devices have High Security (HS) variants along with the non-HS already
supported. Like the previous generation devices (OMAP/Keystone2) K3
supports boot chain-of-trust by authenticating and optionally decrypting
images as they are unpacked from FIT images. Add support for this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Activate the command poweroff by default for STM32MP1:
- with PCSI from TF-A for trusted boot
- with PMIC sysreset request for basic boot (SYSRESET_POWER)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
remove SCSI and SCSI_AHCI configs for ls1043ardb due to no sata interface
support.
this changed is to fixed the ls1043ardb compile warning as fallows:
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the
v2019.07 release. Failure to update by the deadline may
result in board removal.See doc/driver-model/MIGRATION.txt
for more info.
====================================================
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[PK: reword the patch subject]
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This add the initial support of the broadcom reference
board bcm963158 with a bcm63158 SoC.
This board has 1 GB of ram, 512 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm63158 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CLK and DM_RESET drivers are now available for all of
the Allwinner platforms, so enable them in arch/arm/Kconfig
Enabling CLK will select DM_RESET by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For a small SPL, it should be possible to build without SPI(-flash) drivers
or wihout MMC drivers.
For this to work, we have to change from 'select'ing options to 'imply'ing
them.
With this change, I can have SPL trimmed to my hard-wired starting method
(SPI-NOR or MMC) while still including all drivers in U-Boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Set environment variable 'platform' containing the CPU type.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BSS section was all the time separated for SPL but this symbol wasn't
enabled. It is necessary to have it enabled for OF_SEPARATE
configuration where DTB is appended to u-boot with DTB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds a Kconfig file in the board directory, so that some
board-specific options can be specified there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable modern fitImage format on sunxi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
