All rockchip platforms support TPL or SPL-based bootloader
in mainline with U-Boot proper as final stage. For each
stage we need to burn the image on to flash with respective
offsets.
This patch creates a single boot image component using
- binman, for arm32 rockchip platforms
- pad_cat, for arm64 rockchip platforms.
This would help users to get rid of burning different
boot stage images.
The new image called 'u-boot-rockchip.bin'
which can burn into flash like:
₹ sudo dd if=u-boot-rockchip.bin of=/dev/sda seek=64
This would support all rockchip platforms, except rk3128
since it doesn't support for SPL yet.
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootcount support for Rockchip rk3399.
The bootcount value is preserved in PMU_SYS_REG0 register,
this would help to support redundent boot.
Once the redundant boot triggers, the altboot command
will look for extlinux-rollback.conf on particular
bootable partition which supposed to be a recovery
partition where redundant boot required.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
rk3399 do support SPI flash as well, so there is
a possibility of using flash environment for those
usecases.
So define env device for MMC only when it is used
by specific configuration.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable support for DFU over USB. This requires to enable USB gadget,
DWC2 UDC OTG driver and DFU command. DFU entities are defined for the
following firmware objects: u-boot.bin, uboot.env, config.txt, and
zImage/Image.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This fixes the default boot command for the SD-card boot case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The linux kernel Image is growing quite quickly,
if kernel Image size grow beyond 36 MB then
kernel Image at load address 0x81000000
overlaps with the reserved memory region
at 0x83400000.
Adjust kernel load address(kernel_addr_r) from
0x81000000 to 0x96000000 to avoid kernel Image
overlapping with reserved memory region.
This change fixes the below U-Boot error while
booting uncompressed kernel Image through booti command,
ERROR: reserving fdt memory region failed (addr=83400000 size=c00000)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
FIT image contents can be larger than default bootm limit 8M
with initrd. Raise limit to 64MB which is commonly used
elsewhere.
Signed-off-by: Dhananjay Phadke <dphadke@linux.microsoft.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This board is similar to SUV31, but the FPGA is reset concept is quite
different.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch moves the qrio and i2c deblocking code to
keymile/common as it will also be used by the upcoming CENT2 board.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
When using fitImage in AARCH64, the fdt is only 4 byte aligned.
According to linux kernel -> Documentation/arm64/booting.txt, the
fdt *must* be 8 byte aligned. Therefore, it is somewhat random,
if you build a kernel that the fdt is 4 or 8 byte aligned.
Removing fdt_high (or changing it to a valid 8 byte aligned
address) solves this issue.
Signed-off-by: Matthias Schoepfer <matthias.schoepfer@ithinx.io>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Use MMC0 for eMMC and MMC2 for SD-card as other Exynos-based boards do.
This allows to use common code to get MMC device id based on the XOM[7:5]
pins.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable USB keyboard to be used as input device at U-Boot prompt. Both
serial and USB keyboard will be active inputs simultaneously.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add env variables that set up dfu_alt_info for MMC/EMMC/OSPI. This
is required to allow update of firmware on these media.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Both 'loadfit' and 'mmcloados' start with a call to 'args_mmc' so this
can be factored out to before eithers only call site. This also allows us
to remove that call from 'loadfit', which should not have been calling it
anyway as that command should not be MMC specific. Without the call to
'args_mmc' the command 'loadfit' becomes just a call to 'run_fit' so
remove the indirection and call 'run_fit' directly, this removes the need
for 'loadfit' command (which was misnamed anyway). Drop it.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some of the environment configuration in AM65x is not available in
J721e due to additions on one but not the other. These two platforms
are similar enough these common definitions should be factored out
to a common area, prepare for this by synchronizing them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Commit 8502fe84a4 ("configs: am57xx_evm: define
CONFIG_SPL_LOAD_FIT_ADDRESS for SPL-DFU") implements incorrect ifdef
logic, which leads to DFU variables absence in non-SPL environment. Fix
that in order to bring back DFU variables, by reflecting the logic in
include/configs/dra7xx_evm.h.
Fixes: 8502fe84a4 ("configs: am57xx_evm: define CONFIG_SPL_LOAD_F...")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
These are necessities for beaglebone ai boot. There is the addition of
CONFIG_SUPPORT_EMMC_CONFIG to the Kconfig file. This is present upstream
but not in 19.01 yet.
Signed-off-by: Jason Kridner <jdk@ti.com>
Signed-off-by: Caleb Robey <c-robey@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since CONFIG_LOADADDR is not set, the default value of $loadaddr
variable is not set in the environment either. Set the default
load address to 32 MiB from the start of DRAM (same value than
kernel_addr_r).
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Not all systems have all the boot devices enabled, e.g. not all systems
have MTD devices and thus do not enable UBI. Make all the boot devices
in the distro bootcmd conditional to avoid failures.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
SoC base addresses should better go into a common SoC file instead
of repeating the definition in each board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As we use the driver model for ESDHC there is no need
for defining CONFIG_SYS_FSL_USDHC_NUM and CONFIG_SYS_FSL_ESDHC_ADDR,
so simply remove them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This adds a general board file based on MT7622 SoCs from MediaTek.
This commit is adding the basic boot support for the MT7622 rfb.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
The below patch added eSDHC periperhal clock code initially.
2d9ca2c mmc: fsl_esdhc: Add peripheral clock support
The purpose was to fix up device tree properties "peripheral-frequency"
so that linux could get the periperhal clock by it.
However the implementation on both u-boot and linux was only
for a Freescale SDK release. The linux part implementation had never
been upstreamed. These code should not have been exist on u-boot
mainline.
Let's remove the powerpc part changes but keep the changes in
fsl_esdhc driver. The changes in fsl_esdhc driver could be utilized
to support SD UHS and eMMC HS200/HS400 speed modes for current
Layerscape ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Follow i.MX, Sunxi, RISC-V and Rockchip to generate u-boot.itb which
includes U-Boot proper, ATF and DTBs in FIT format. ZynqMP supports FIT for
quite a long time but with using out of tree solution. The patch is filling
this gap.
Tested on zcu102, zcu104 and zcu100/Ultra96.
zcu100/Ultra96 v2.2 ATF build by:
make DEBUG=0 ZYNQMP_CONSOLE=cadence1 RESET_TO_BL31=1 PLAT=zynqmp bl31
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript
file in DDR and execute it first incase of jtag bootmode.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This target is out of maintenance and can be removed.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Stefan Roese <sr@denx.de>
CC: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Reviewed-by: Stefan Roese <sr@denx.de>
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
As previous CONFIG_SYS_UBOOT_START is now set by default to
CONFIG_SYS_TEXT_BASE when not defined, CONFIG_SYS_UBOOT_START
can be removed from include/configs board files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This complements commit 068789773d which did the conversion for
mpc85xx.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Mario Six <mario.six@gdsys.cc>
Enable GIC support for G12A/G12B platform.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This fixes a merge error that accidentally left CONFIG_MTD_DEVICE
active by removing it from the config file.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add build support for Agilex SoC.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Move Stratix10 and Agilex common CONFIGs to socfpga_soc64_common.h.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Now all the fec related phy properties are now accessible
via dts. So drop the explicit config items from common
config file, imx6-engicam.h
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Adjust the environment for booting a mainline kernel by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We switch from custom boot commands relying on uEnv.txt to distro boot.
This removes the automatic fpga bitstream loading in favor of loading
bitstreams via custom bootscripts (boot.scr) or after booting the
kernel.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Enable driver model for SPI and SPI_FLASH to remove the following
compile warning on CM-FX6 SOM:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
====================================================
This change introduced SPL build error as shown:
In file included from include/common.h:47:0,
from drivers/mtd/spi/sf_probe.c:10:
drivers/mtd/spi/sf_probe.c: In function 'spi_flash_std_probe':
drivers/mtd/spi/sf_probe.c:149:54: error: dereferencing pointer to incomplete type 'struct dm_spi_slave_platdata'
scripts/Makefile.build:278: recipe for target 'spl/drivers/mtd/spi/sf_probe.o' failed
make[3]: *** [spl/drivers/mtd/spi/sf_probe.o] Error 1
scripts/Makefile.build:432: recipe for target 'spl/drivers/mtd/spi' failed
make[2]: *** [spl/drivers/mtd/spi] Error 2
Disabling DM for SPI support(SPI and SF) in SPL resolves the issue.
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
The SPL does not have DM enabled and therefor still needs to use the
hardware watchdog interface provided by the imx-watchdog driver.
Fixes: broken reset command after f2929d11a6 ("watchdog: imx: Use
immediate reset bits for expire_now")
Signed-off-by: Claudius Heine <ch@denx.de>
Make first step in DT/DM migration. Enable OF_CONTROL only for the main
U-Boot image for now.
Remove mmc_init_main() because board_mmc_init() is not called when
DM_MMC is enabled.
DM_MMC requires DM_GPIO for card-detect to work. That in turn makes gpio
request mandatory. Add code to request/free gpios in platform code.
MMC devices are now numbered according to DT. The SD card is 1, and eMMC
is 2. Account for that in board_mmc_get_env_dev(), BOOT_TARGET_DEVICES,
and has_emmc().
DM_MMC requires BLK. However, the (BLK && !DM_USB) combination disables
USB_STORAGE. Enable DM_USB to preserve USB functionality. Add also
DM_REGULATORS for the USB power controller. This allows us to drop
board_ehci_hcd_init() and setup_usb().
Runtime selection of DT is necessary because of the i.MX6QD vs i.MX6SDL
incompatibility. DT selection does not rely on GPIOs, since DM_GPIO
depends on DT. Instead, we take one "fully featured" DT of each variant.
That should be enough to boot from both SD card and eMMC.
Since we don't select the exact DT, override the generic
show_board_info() that shows the selected DT 'model' field.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pass rtc_status via the device tree, instead of on kernel command line.
Additionally, the 2038 mitigation is reported, if applied successfully.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
DM for PCI pulls DM for ethernet that also needs other changes described
below to build u-boot and keep existing functionality - ability to update
MAC addresses of FEC ethernet adapter and I210 adapter connected to the
Marvell switch.
- fec_mxc driver with DM needs PHYLIB;
- configuration items are moved from ge_bx50v3.h to ge_bx50v3_defconfig;
- FEC is marked as eth0 because it is always present, so indices changed:
I210 are still probed in the same order;
- board_eth_init() was used by legacy ethernet, setup for enet iomux and
pcie is moved to the board_late_init();
- pci_init() is called from the board_late_init() to initiate PCI bus
probing, so I210 devices are propagated to the device tree;
Signed-off-by: Denis Zalevskiy <denis.zalevskiy@ge.com>
[Describe PHY reset in device tree]
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Use vidconsole for output to the LCD, now that DM_VIDEO is used. Write
white text on a black background, like before migrating to DM_VIDEO.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb) by using OF_PLATDATA.
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet@800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
sync defaut Envoronment with customer changes.
Unfortunately they are not changeable, as already
board is in production mode.
Get rid of the big bootcommand and set bootcommand
through Kconfig option.
Signed-off-by: Heiko Schocher <hs@denx.de>
add DM_VIDEO support and remove now unneeded board
code. As we show a bmp logo on boot, call now
bmp_display() from board code and do not use
cfb_console anymore.
Signed-off-by: Heiko Schocher <hs@denx.de>
enable CONFIG_DM_SPI and CONFIG_DM_SPI_FLASH
and get rid of build removal warnings.
define CONFIG_GPIO_ENABLE_SPI_FLASH is not longer
needed, so remove it from config_whitelist.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
remove aristainetos-v2.c file, as we now want to
switch to DM/DTS support and have all board specific
code in one file. Goal is to setup differences
through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
