Use the `do_reset` implementation of `arch/arm/lib/reset.c` in SPL
instead. It is very close to what is done here, anyway, and plays
more nicely with the rest of U-Boot than adding a custom `do_reset`
implementation into board files.
`do_reset` from `arch/arm/lib/reset.c` calls `reset_cpu` with 0 as the
addr parameter while the boards are passing WDOG1_BASE_ADDR. This is
ok because the `reset_cpu` implementation uses WDOG1_BASE_ADDR by
default if 0 is passed in.
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.
The module also adds some commands:
- snvs_cfg: Configure the SNVS HP and LP registers
- snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
- tamper_pin_cfg: Change the configuration of the tamper pins
- snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
status bits
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
mux changes in board file to enable lpuart1 and macro
define for lpuart1 used for mux changes in board configuation
register 13
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for
DPAA2 Ethernet devices. Compile out any unnecessary setup when
CONFIG_DM_ETH is activated.
Also, force the PCI devices to be enumerated at probe time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move GIC redistributor tables initialization to CPU setup function.
This patch introduces a GIC redistributor tables init function, and
moves the function of reserving memory for GIC redistributor tables
to soc.c and adds a argument for the memory size to reserve, BTW
rename the function so that it is more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
As the lower 16bit of the redistributor pending table is reserved
for describing the memory attributes, we must give a 64KB aligned
address to the GIC LPI initialization function.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Program the GIC redistributor tables only when succeeded to reserve memory
for them, otherwise kernel will lose the chance to program them using
allocated memory.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The WRLVL_START values are optimized for old DDR MTA18ASF1G72AZ.
Update DDR struct to set new WRLVL_START values so that the new DIMM
MTA18ADF2G72AZ get optimized and the old DIMM still works.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on t208xqds: remove board specific fixups
on t208xqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on lx2160aqds: remove board specific fixups
on lx2160aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for backplane kr on ls1046aqds: remove board specific fixups
on ls1046aqds for ethernet interfaces specified in device tree as
supported backplane modes.
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If the board is configured without CONFIG_GIC_V3_ITS, an error occurs:
board/freescale/lx2160a/lx2160a.c: In function ‘ft_board_setup’:
board/freescale/lx2160a/lx2160a.c:673:6: error: unused variable
‘gic_lpi_base’ [-Werror=unused-variable]
673 | u64 gic_lpi_base;
| ^~~~~~~~~~~~
Let's define the variable as __maybe_unused.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After triggering a "reboot" command in Linux the following
hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because the CMD_ERR bit is set in the IRQ status
register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
mx6ul_evk uses DM_ETH, so there is no need to have board code
to setup the FEC IOMUX and to register the network ports via the
old board_eth_init() method.
Remove these FEC related pieces of code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update reference in files detected by
scripts/documentation-file-ref-check
doc/README.<board> => board/<board>/README
Files moved in board directory in
commit 702e6014f1 ("doc: cleanup - move board
READMEs into respective board directories")'
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imx8image => imx/mkimage/imx8image.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update reference in many files detected by
scripts/documentation-file-ref-check
README.imximage => imx/mkimage/imximage.txt
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add config to enable the PFE and ETH support.
Also change the pfe secure boot header address.
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The SDHC1_DAT4 signal could be routes to SDHC1_VS or SDHC1
adapter slot for SDHC1 usage. When SDHC1 is selected in RCW,
do not force to route it to SDHC1 adapter slot if find it
has already been configued for SDHC1_VS.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Set VID to 800 mV for Rev1 and set VID as per switch settings
for Rev2.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program GIC LPI configuration table:
1. Redistributor PROCBASER configuration table (which
is common for all redistributors)
2. Redistributor pending table (PENDBASER), for all the
available redistributors.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update "board_fix_fdt" with correct counter value "i".
This will fix the issue while fetching the "reg_names"
resource from fdt after fixup.
Signed-off-by: Vikas Singh <vikas.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As there is only one mx31pdk config file and with upcoming updates to
the Kconfig parsing logic, rather than have an entry in
board/freescale/mx31pdk/Kconfig, move this single setting to the
defconfig file.
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This should help keeping the screen black when booting the kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd PCI to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_PCI Please update
the board to use CONFIG_DM_PCI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
After the conversion the following commands were used for testing:
=> pci enum
PCI: Failed autoconfig bar 10
PCI: Failed autoconfig bar 10
=> pci 1
Scanning PCI devices on bus 1
BusDevFun VendorId DeviceId Device Class Sub-Class
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently there are two targets for the i.MX6SX SabreSD board:
mx6sxsabresd_defconfig and mx6sxsabresd_spl_defconfig.
This brings additional maintainance effort without a clear
advantage.
Keep only the mx6sxsabresd_defconfig one and remove
mx6sxsabresd_spl_defconfig to keep it simpler.
Also remove the SPL related code from the board file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Inside Kconfig we must not use the CONFIG_ prefix with the imply statement.
Fixes: 28e3c39e53 ("board: freescale: ls1012a2g5rdb: enable network
support on ls1012a2g5rdb")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1021A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support of "qixis_reset emmc" command for lx2160a based platforms
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix loop in board_fix_fdt that erroneously increments the counter
in all cases whereas the counter should be incremented only if a
matching string has been found.
Fixes: 5d535aa40b ("board: fsl: lx2160a: implement board_fix_fdt")
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The dts node of the DSPI controller in kernel is spi instead of dspi,
it is not correct if use "/soc/dspi@" to fix up the status of the dts
in kernel, so, modify it to "/soc/spi@".
The DSPI2 and I2C5 are muxed, and the status of DSPI2 node in kernel dts
default value is okay, So set the status of DSPI2 node in kernel dts to
disabled if it is muxed as I2C5.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:115:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:102:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:116:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:129:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Functions spl_dram_init() and power_init_board() are used only in
the scope of this file, so make them static to fix the following sparse
warnings:
board/freescale/imx8mm_evk/spl.c:40:6: warning: no previous prototype
for ‘spl_dram_init’ [-Wmissing-prototypes]
board/freescale/imx8mm_evk/spl.c:85:5: warning: no previous prototype
for ‘power_init_board’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add sys_proto.h header file to fix the following sparse warning:
board/freescale/imx8mm_evk/imx8mm_evk.c:59:5: warning: no previous
prototype for ‘board_mmc_get_env_dev’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The imx8mm doesn't require the hdmi firmware.
Update also the fw version.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With commit 0d52bab462 ("mx7dsabre: Enable DM_ETH")
Device Tree has been update and change pfuze3000 node
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently the following SPL hang is observed:
U-Boot SPL 2020.01-rc5-00079-g797eee36a1 (Jan 06 2020 - 11:24:09 -0300)
Trying to boot from MMC1
Card did not respond to voltage select!
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Fix it by moving the eSDHC2 initialization to SPL.
While at it, since this board uses DM_MMC all the esdhc board
code can be removed to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
All platforms currently use the "MCFTMR" DMA timer rather than the PIT
timer, so drop the MCFPIT code.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@sysam.it>
Add board_mmc_get_env_dev, otherwise,
Loading Environment from MMC...
MMC Device 0 not found
*** Warning - No MMC card found, using default environment
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The DDR firmware binaries are not part of the U-Boot source code, so
we should look for them in the build directory, where they need to be
copied to before building U-Boot.
The ATF binary is already fetched from the build directory, but the
README files for the i.MX8M EVKs claim that it needs to be copied to
the source directory (which is still true for in-tree builds, but not
in general). Therefore we also fix the READMEs to use the build
directory as the correct location for all additional binary files.
Sined-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
