Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.
When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We use non-dm code to configure the clk settings in order to simplify
dm clk driver in future, so remove the duplicated code from clk driver
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To fused part, we need to disable nodes of dtb to let kernel boot.
To mfgtool, USB issue when using super-speed for mfgtool, temporally
work around the problem to use high-speed only.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To use one defconfig for all boot device, we have to runtime set
env offset and return env medium according to the boot device.
This patch overrides the env_get_offset and env_get_location to
implement the feature.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
iMX8MP has 6 fused parts in each qualification tier, with core, VPU,
ISP, NPU or DSP fused respectively.
The configuration tables for enabled modules:
MIMX8ML8DVNLZAA Quad Core, VPU, NPU, ISP, DSP
MIMX8ML7DVNLZAA Quad Core, NPU, ISP
MIMX8ML6DVNLZAA Quad Core, VPU, ISP
MIMX8ML5DVNLZAA Quad Core, VPU
MIMX8ML4DVNLZAA Quad Lite
MIMX8ML3DVNLZAA Dual Core, VPU, NPU, ISP, DSP
Add the support in U-Boot
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
ROM SError happens on two cases:
1. ERR050342, on iMX8MQ HDCP enabled parts ROM writes to GPV1 register, but
when ROM patch lock is fused, this write will cause SError.
2. ERR050350, on iMX8MQ/MM/MN, when the field return fuse is burned, HAB
is field return mode, but the last 4K of ROM is still protected and cause
SError.
Since ROM mask SError until ATF unmask it, so then ATF always meets the
exception. This patch works around the issue in SPL by enabling SPL
Exception vectors table and the SError exception, take the exception
to eret immediately to clear the SError.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add imx_eqos_txclk_set_rate/imx_get_eqos_csr_clk to override the
weak function in driver
Add set_clk_eqos to configure eQoS clk
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current DM CLK is a bit complicated, for simplity, let DM clk only
support enable/disable/get_rate. For the expected rate settings,
we use non-DM clk to do that. Then we could have simple DM clk for
i.MX and could also share between SPL/U-Boot proper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
A53 CCM root max support 1GHz, to support high freq, we need
to switch ARM clk sources from ARM PLL directly.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clocks for FEC and flexspi, and add set parent clock callback,
so DTS can assign clocks
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add USB relevant clocks to support usb clock settings for both
DM USB host and gadget drivers
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add set clock parent support.
Add ENET and flexspi related clocks to support assigned clocks
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The soc info without initialization value should be put into
data section. The driver could be used before relocation,
with it in BSS section could cause issue, since BSS section
is not initializated and it might overwrite other areas that
used by others, such as dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In uMCTL2 Databook, for LPDDR4, it is recommended to set
this register to 1. This can avoid ddr bandwidth is lower
after booting with running for a while.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. set SCHED.rdwr_idle_gap=0
2. set SCHED.pageclose=1
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The 'selfref_en' should be bit'0', so correct the setting to
enable the auto self-refresh.
Reviewed-by: Jian Li <jian.li@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no DDR_SS_GPR0 exits on i.MX8MN, so skip setting
this register on i.MX8MN.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that commit 3e57f879ee ("mtd: nand: raw: denali: Assert reset
before deassert") added the reset assertion, this code in the board
file is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixed delay 200us is not working in certain platforms. Change to
poll for reset completion status to have more reliable reset process.
Controller will set the rst_comp bit in intr_status register after
controller has completed its reset and initialization process.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Always put the controller in reset, then take it out of reset.
This is to make sure controller always in reset state in both SPL and
proper Uboot.
This is preparation for the next patch to poll for reset completion
(rst_comp) bit after reset.
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Radu Bacrau <radu.bacrau@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This UART controller is integrated with a FIFO. Enable it.
You can put the next character into the FIFO while the transmitter
is sending out the current character. This works slightly faster.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Ensure the transmitter is empty when chaining the baudrate or any
hardware settings. If a character is remaining in the transmitter,
the console will be garbled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
After all, I am not a big fan of using a structure to represent the
hardware register map.
You do not need to know the entire register map.
Add only necessary register macros.
Use FIELD_PREP() instead of maintaining a pair of shift and mask.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that this directory contains only uniphier_sbc_boot_is_swapped(),
move it to boot-device.c and delete the sbc/ directory entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 1517126fda ("ARM: uniphier: select DM_ETH"), DM-based
drivers/net/smc911x.c is compiled, but it is never probed because the
parent node lacks the DM-based driver.
I need a skeleton driver to populate child devices (but the next commit
will move more hardware settings to the this driver).
I put this to drivers/bus/uniphier-system-bus.c because this is the
same path as the driver in Linux kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I actually do not see this used these days because eMMC or NAND is used
for non-volatile devices. Dump the burden to maintain this crappy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This was used by the old sLD3 SoC, the support of which was removed
by commit 00aa453ebf ("ARM: uniphier: remove sLD3 SoC support").
There is no more user of this function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
