This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
It is possible to flag MAC addresses as locally administred. In this
case they don't need to be unique. This is only allowed for interfaces
which have no connection to the outside. For the TEGR1 board we use
this feature.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
If we rebrand the IVM and ethaddr was set previously we need to change
ethaddr. Otherwise we end up with a wrong MAC adress for the ethernet
interface.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
The 82xx board mgcoge3ne was removed from the codebase, so this is dead
code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board uses the same CPU (8309) as VECT1. The memory however is
different since it has NAND Flash, the NOR Flash partitioning is
different and of course the FPGAs as well.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
Setting dip_switch 3 and 4 also will run bootloader in COGE3 and COGE6
It is required remove local mgmt IP address, when DIP Switch PIN3 is
enabled. DIP Switch 4 also enabled to avoid u-boot update in future
for DIP switch enhancements.
Signed-off-by: Bagavathiannan Palanisamy <Bagavathiannan.Palanisamy@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
commit 0a4f88b98 removed the usage of our setports function, but the
function itself were not removed. So toss it it's dead code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
We use CONFIG_OF_LIBFDT and CONFIG_OF_BOARD_SETUP on all our powerpc
targets, so there is no need to check these defines within our C code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
On mgcoge3ne we also want to start the test application if the testpin
is asserted. But we don't have a full POST test support yet. So simply
add a function to read the testpin value.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The get_pin and set_pin funciton was only used for pins on Port D and
therefore the value was hard coded in the function. Enhance this with a
parameter, that we are able to use this functions for other ports too.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This board is similar to TUXX1, but it has differend FPGAs.
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Search for the kernel and DTBs in a folder named PRODUCTNAME (found in the IVM)
at the TFTP server instead of the u-boot boardname.
Signed-off-by: Tobias Müller <Tobias.Mueller@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When loading the dtb file via tftp we should load the one which matches
boardId and hwKey and not a common one for the boardname. We have boards
were different hwKeys are used and then we may load an incorrect dtb
file. If no fdt_bid_kwkey.dtb file is not a fallback to boardname.dtb is used.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Tobias Müller <Tobias.Mueller@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
There was a small typo for KM_COGE5UN that resulted in the dip switch
not to behave as expected.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Similar to kmcoge5un we need to check the dip switch at startup
connected to the kirkwood at MPP43. If it's set we need to set the
actual_bank to zero to boot from SW bank zero. Additional to kmcoge5un
we need to check also the pin in misc_init to decide wether we wait for
the ne to start or not. If the dip_switch is set we don't wait and
continue immediately.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Configure PHY LED register for Marvell 88E1118R PHY used on PIGGY3 to
match with printed descriptions on PCB
Signed-off-by: Tobias Müller <Tobias.Mueller@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[trini: Fix typo, CRTL_PAGE -> CTRL_PAGE]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is not used anymore since the procedure was split into a simple
read function and a later alaysis.
The ivm_read_eeprom name is now used for the previous
ivm_simple_read_eeprom function.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.
Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.
Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.
Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.
Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This allows to first read the IVM content (earlier in the boot sequence)
and define the ethaddr env variable thanks to the ivm_read_eepromi().
Later, the IVM content can be parsed and used to define some hush
variables, when the hush subsystem is available thanks to
ivm_analyze_eeprom().
To avoid the HW read to happen twice, the buffer passed to
ivm_read_eeprom() has to be reused by ivm_analyze_eeprom (and thus
allocated before calling ivm_read_eeprom()).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.
This makes is possible to use those gpio functions from other MVEBU SoC's
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This makes is possible to use those gpio functions from other MVEBU SoC's as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.
Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
There is the requirement on the chassis's backplane that when the clocks
have been enabled, they then should not disappear.
Resetting the Zarlink clocking chips at unit reset violates this
requirement because the backplane clocks are not supplied during the
reset time.
To avoid this side effect, both the Zarlink clocking chips are reset
only at power up.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch configures the qrio to trigger a core reset on
a CPU reset request.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To acheive this, the qrio_uprstreq() function that sets the UPRSTREQN
flag in the qrio RESCNF reg is added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check the core timer status register (TSR) for watchdog reset,
and and set the QRIO's reset reason flag REASON1[0] accordingly.
This allows the appliction SW to identify the cpu watchdog as a
reset reason, by setting the REASON1[0] flag in the QRIO.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To achieve this, the qrio_cpuwd_flag() function that sets the CPU watchdog
flag in the REASON1 reg is added.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Clang interpretes an if condition like "if ((a = b) == NULL)
as it tries to assign a value in a statement. Hence if you do
"if ((something)) it warns you that you might be confused.
Hence drop the double braces for plane if statements.
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This should prevent the problems that the CCF can deadlock with certain
traffic patterns.
This also fixes the workaround for A-006559 that was not correctly
implemented before.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Fix the IRQ/GPIO settings: all the muxed GPIO/external IRQs that are
used as internal interrupts are defined as GPIOs to avoid confusion
between the internal/external interrupts.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This adds the reset support for the following devices that was until
then not implemented:
- BFTIC4
- QSFPs
This also fixes the configuration of the prst behaviour for the other
resets: Only the u-boot and kernel relevant subsystems are taken out of
reset (pcie, ZL30158, and front eth phy).
Most of the prst config move to misc_init_f(), except for the PCIe
related ones that are in pci_init_board and the bftic and ZL30158 ones
that should be done as soon as possible.
Only the behavior of the Hooper reset is changed according to the
documentation as the application is not able to not configure the switch
when it is not reset.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
a script by setting the active bank to testbank
The post_hotkeys_pressed return the state of the SELFTEST pin.
The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.
Finally, the unused #defines for the not so relevant mtest command are
removed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Add readout of dip-switch to revert to factory settings.
If one or more dip-switch are set, launch bank 0 that contains the
bootloader to do the required action.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The unit LEDs are managed by the QRIO CPLD. This patch adds support for
accessing these LEDs in the QRIO.
The LEDs then are set to a correct boot state:
- UNIT-LED is red
- BOOT-LED is on.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Cc: Valentin Longchamp <valenting.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.
We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available
For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.
Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".
Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt" [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]
This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.
The machid was left unchanged, this should keep compatibility with both
older and newer kernels.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
CONFIG_BOOTCOUNT_LIMIT is used on all boards from this board series. So
remove this unneeded define.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The PEXHC PCIe configuration mechanism ensures that the FPGA get
configured at power-up. Since all the PCIe devices should be configured
when the kernel start, u-boot has to take care that the FPGA gets
configured also in other reset scenarios, mostly because of possible
configuration change.
The used mechanism is taken from the km_kirkwood design and adapted to
the kmp204x case (slightly different HW and PCIe configuration).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On the previous HW revision (now unsupported), there was a need for
external DMA signals and thus the I2C3/4 signals were used
DMA1_DONE/ACK/REQ.
These signals now are configured as GPIO[16:19].
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to the errata, some bits of an undocumented register in the
DCSR must be set for every core in order to avoid a possible data or
instruction corruption.
This is required for the 2.0 revision of the P2041 that should be used
as soon as available in our design.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The QRIO GPIO functions can be of general interest. They are thus added
to a qrio.c and their prototype are available from kmp204x.h. The QRIO
prst function are also included in this file, as well as the functions
required for the I2C deblocking support (open-drain).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c]
Signed-off-by: York Sun <yorksun@freescale.com>
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
This patch introduces the support for Keymile's kmp204x reference
design. This design is based on Freescale's P2040/P2041 SoC.
The peripherals used by this design are:
- DDR3 RAM with SPD support
- SPI NOR Flash as boot medium
- NAND Flash
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
FPGA
- 2 HW I2C busses
- last but not least, the mandatory serial port
The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb
support and was changed according to our design (that means essentially
removing what is not present on the designs and a few adaptations).
There is currently only one prototype board that is based on this design
and this patch also introduces it. The board is called kmlion1.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
kmp204x: update the ENV #define
The comments had to be refined as well as the total size
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix ddr.c]
Acked-by: York Sun <yorksun@freescale.com>
This must be defined by a board support file that want to use the
keymile common.c board_eth_init function that requires ethernet_present
to be defined.
Currently all the km architectures use it but the kmp204x architecture
later supported in this series does use another board_eth_init function
and thus does not define it.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This must be defined for all the keymile boards that use the common
i2c_abort function that is used to "reset" the I2C bus. These are
currently km82xx and km_arm boards.
The km83xx boards use other functions and thus do not need this.
This patch removes the CONFIG_SYS_I2C_INIT_BOARD from keymile-common.h
and defines it for km_arm.h and km82xx.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
commit a5510058 powerpc/83xx/km: make local functions and structs static
removed the staticness also from this struct. But this struct is needed
in arch/powerpc/cpu/mpc83xx/cpu_init.c and declared as extern.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
as the keymile boards use now the new i2c multibus/multiadapter
framework, remove the EEprom_ivm Environmentvar, as not longer
needed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Replace uImage with ${uimage}.
If uimage is not set, default it to uImage.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
kmvect1 has a UEC2 connection to the piggy board and a UEC0 connection
to the switch MV88E6122. This switch has a connection to a frontport
ethernet interface. The ethernet port used for network booting is
automatically selected by u-boot. If a Piggy is plugged, the Piggy
port is selected (UEC2, eth1). If the Piggy isn't present, the
Frontport is selected (UEC0, eth0).
The switch reset is connected to a GPIO on the PRIO3 board FPGA (GPIO28)
and released at startup.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
For the the kmvect1 board we will also need a functionality to add an
offset to the IVMs MAC address, because these board will have two valid
ethernet ports for debugging purpose. So move the code to an own
function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
For kmvect1 we need a special solution and for km_arm boards we already
have. So move the common code to the architectur specific file.
Signed-off-by: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This saves stack and code memory for local copy, and
consumes initialized data memory. For 22 of the 29
kirkwood-based boards, this results in a global saving
of about 30 bytes. For 7 of them, it results in an
increase of 6 to 14 bytes.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch removes 2 small portions of board specific code that are
duplicated with common ARM code and thus unnecessary. These 2 portions
of code concern the mach id that is given by u-boot to the Linux kernel
to identify the system's MACH.
The first one was the possibility to change the MACH thanks to the
'mach_id' enviroment variable. This is possible thanks to the 'machid'
env variable (see arch/arm/lib/bootm.c:boot_jump_linux()).
The seconde one is the setting of the bi_arch_number. This is already
done in arch/arm/lib/board.c:board_init_f() since km_arm.h does #define
CONFIG_MACH_TYPE.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
On kmcoge5un we faced some serious problems with the memory during
temperature tests. Reason was that we overwrite some registers for
memory settings which have to leave untouched. These where registers
0x20148 , 0x2014c and 0x20154.
So writing these registers is prohibited and this patch removes them
from all km related config files. Even if the problem was only
seen on kmcoge5un.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The kmnusa board uses a mv88e6352 switch that is connected to the main
eth interface of the kirkwood. Therefore the switch must be configured
so that the kirkwood's egiga eth inferface can be used.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Some boards may differ only in the SDRAM size. This function allows to
fix the size accordingly and we can use the same u-boot binary for both
boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
For some reasons we had an own implementaion of dram_init and
dram_init_banksize. This is not needed anymore, use the standard
kirkwood functions instead.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
The fanless boards now have a 7-digit (XXXXX-F) board name. This
triggers a border condition when reading this string in the IVM although
this string is smaller than the currenly read string size, but only by 1
character.
This patch corrects this by changing the size check condition for string
length. It is the same change that was done in the platform for this
same bug.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Stefan Bigler <stefan.bigler@keymile.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch adds SDRAM detection feature to km82xx boards.
To enable this feature, define CONFIG_SYS_SDRAM_LIST as the initializer
for an array of struct sdram_conf_s.
These structs will expose the bitfields within registers PSDMR and OR1 which
have to be different between configurations; common bitfields will be
defined, as usual, within CONFIG_SYS_PSDMR and CONFIG_SYS_OR1.
If CONFIG_SYS_SDRAM_LIST is not defined, then the usual behavior is retained.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
This code will also be used before reallocation and during this time we
are not allowed to do these printings.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Prafulla Wadaskar <Prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
Also drop a few files referring to no longer / not yet supported
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
These functions tried to access two static tables before relocation
(board_early_init_f is executed before relocation). But these static
tables lie in the bss section which is not valid before relocation.
These accesses then overwrote some parts of u-boot binary before it was
relocated. For the kmnusa build, this results in a corrupted important
env variable (bootcmd) but it may be that some other parts of the u-boot
binary are corrupted.
This patch solves this problem by moving all the kw_gpio_* calls to
board_init, which should be early enough in the boot sequence. The only
calls that could not be moved is the one for the SOFT (bitbang) I2C, and
they have been replaced by a direct access to the GPIO dataout Control
register to set the two GPIOs as output.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Add a function to read the dip_switch on kmcoge5un. If the
switch is set the actual_bank is set to 0 and this SW is
booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
The PCIe FPGAs now have to support 2 resets: one for the non traffic
affecting part (PCIe) and one for the traffic affecting part.
When the FPGA is not reconfigured, we only reset the PCIe part.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
In order to be able to perform board resets without interrupting the
traffic, the configuration of an already properly configured FPGA is
skipped.
This is because some PCIe FPGAs embed some other function that must
continue to work over reset.
It is then the responsibility of the application to trigger a
reconfiguration when needed. This is done by lowering the FPGA_INIT_B
pin for delaying the configuration to u-boot @ next reboot, and then
lower the FPGA_PROGRAM_B signal.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1
for the end of the FPGA configuration (with a timeout)
3) reset the FPGA
4) finally remove the access to its config EEPROM from the FPGA so that
the CPU can update the FPGA configuration when the kernel is running
The boards with a PCIe FPGA but without BOCO2 still are supported.
The config option name is CONFIG_KM_FPGA_CONFIG
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Use the generic header km_kirkwood.h and get rid of the
board specific header.
changes for v2: rebased because of changes in other patches
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween, this needs a new configuration for the mvgbe driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.
Some other details:
- IVM EEPROM is at adress: pca9547:70:9
- PCI is enabled
- PIGGY4 is connected via MV88E6352 simple switch. There is no phy
between the simple switch and the kirkwood.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
We overwrite these weak functions from the kirkwood spi code to
use our own method to be able to switch between the SPI NOR and
the NAND flash. This is needed e.g. to update the u-boot. The former
command do_spi_toggle can therefore be removed. And the usage of
this command is removed from the u-boot update command in the
u-boot environment.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
With the new second save argument introduced by the previous patch, all
the calls to the function had to be fixed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
If the testpin is asserted, first check if a test_bank
variable is defined before trying to boot this
test_bank.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On kmcoge5ne we have a dip switch present. If this switch
was switched on the actual_bank is set to 0 and this SW
will be booted.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
kmcoge5ne starts the post tests if the testpin on
the board was enabled. Currently it does simply a memory
test.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Enabled application buffers in uboot to allow application chipselect
access in uboot.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MAC address begins at offset 1.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This board is a MPC8360 board. Two flashes are present
a NOR flash were u-boot and the u-boot environment is stored
and a NAND flash for the application code. This board has 512MB
SDRAM.
Additionaly we introduce a common km8360.h file and convert kmeter1 to
use this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
If the ram size isn't locked to 2GiB, the get_ram_size() may hang up.
Signed-off-by: Christian Herzig <christian.herzig@keymile.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add a variable "toolchain" and configure the rootpath
for the nfsargs with this variable.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Configuring for kmeter1 board...
km83xx_i2c.c: In function 'i2c_make_abort':
km83xx_i2c.c:44:8: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
commit b11f53f3 (keymile: Fix Coding style issues for keymile boards)
introduces a bug according the SDRAM initialization for all
km83xx boards.
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
was replaced with
out_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
and this is wrong, because this overwrites the intial value
CONFIG_SYS_DDR_SDRAM_CFG.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The common code should be valid for more than one architecture.
Therefore this code was reorganized and moved to the new
file km83xx_i2c.c
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
